Summary of Contents for MULTIQUIP DuoScreed LightWeight DSGPULW
Page 1
OPERATION AND PARTS MANUAL MODEL DSGPULW DuoScreed LightWeight (HONDA GX35SAT GASOLINE ENGINE) Revision #7 (09/19/18) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
DSGPULW DUOSCREED — SILICOSSIS WARNING WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give other materials can generate dust, mists and fumes off dust or mists containing crystalline silica.
, 2006 Order via Internet (Dealers Only) Best Deal! If you have an MQ Account, to obtain a Username Order parts on-line using Multiquip’s SmartEquip website! and Password, E-mail us at: parts@multiquip. ■ View Parts Diagrams com. ■ Order Parts To obtain an MQ Account, contact your ■...
Page 6
This gas is colorless and instructions for the safe and odorless, and can cause death if inhaled. NOTE efficient operation of the Multiquip NEVER operate this equipment in a confined Model DSGPULW LightWeight area or enclosed structure that does not (LW) DuoScreed Refer to the provide ample free flow air.
Page 7
DSGPULW DUOSCREED — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard ALWAYS place the engine ON/OFF switch in the OFF position when the DuoScreed is not ALWAYS wear approved respiratory in use. protection. Equipment Damage Messages Sight and Hearing hazard Other important messages are provided throughout this manual to help prevent damage to your DuoScreed, other property, or the surrounding environment.
An explosion or fire could result causing severe bodily harm or even death. recommended by Multiquip for this equipment. Damage ■ Topping-off to filler port is dangerous, as it tends to spill fuel. to the equipment and/or injury to user may result.
Page 9
■ NEVER use accessories or attachments, which are not ■ ALWAYS have easy access to the phone recommended by Multiquip for this equipment. Damage to numbers of the nearest Ambulance , Doctor the equipment and/or injury to user may result.
DSGPULW DUOSCREED — OPERATION AND SAFETY DECALS Machine Safety Decals The DUOSCREED is equipped with a number of safety decals. These decals (Figure 1) are provided for operator safety and maintenance information. The illustrations below shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
DSGPULW DUOSCREED — GENERAL INFORMATION Introduction Engine The Multiquip DuoScreed is a hand held vibratory screed The Multiquip DuoScreed is equipped with a Honda Model designed to strike-off and consolidate concrete slabs. It is GX35SAT, 1.6 HP, mini 4-cycle gasoline engine. This engine is comprised of two major components, the power unit (gasoline lightweight and requires no fuel mixing.
DSGPULW DUOSCREED — COMPONENTS Figure 2. DuoScreed Components Figure 1 shows the location of the components of the DuoScreed. 12. Shock Mounts – Used to absorb the vibration generated The function of each component is described below: by the DuoScreed. These shock mounts minimize the transfer of vibration to the operator.
DSGPULW DUOSCREED — ASSEMBLY INSTRUCTIONS Assembly Instructions Determine whether you will be using the DuoScreed on forms or as a wet screed . This will decide how the power This section will explain how to assemble the DuoScreed. unit will be mounted . If the DuoScreed will be used as a wet screed the wing nuts should be located above the smooth It is recommended that you familiarize edge of the blade.
Page 16
DSGPULW DUOSCREED — ASSEMBLY INSTRUCTIONS Figure 4. Blade Mounting Diagram Two handle bar adjustment knobs (Figure 5) are located at Place the front of the power unit over the blade (Figure 3) the base of the steering handle bar. Loosen these two knobs until the front of the clamp is seated within the front blade to adjust the height of the steering handle bar to a suitable collar.
Page 17
DSGPULW DUOSCREED — ASSEMBLY INSTRUCTIONS Eccentric Weight Adjustment These weights determine the amount of vibration that will travel down the blade. Depending on the type of blade that is used, will There are two eccentric weights (Figure 6) that are supplied determine the position of the two eccentric weights.
DSGPULW DUOSCREED — STARTING Engine Pre-Check 2. Press the priming bulb (Figure 11) repeatedly until fuel can be seen inside the clear plastic bulb. 1. Fill the fuel tank (Figure 8 ) with unleaded gasoline. DO NOT over fill. Topping-off to filler port is dangerous, as it tends to spill fuel.
DSGPULW DUOSCREED — APPLICATION/OPERATION Application/Operation 1. Before placing the DuoScreed in concrete for screeding, 4. Once all the grade pins have been placed correctly and it is a good idea to apply form oil to the blade and all are dead on grade, concrete can then be poured on top frame parts that may come in contact with the concrete.
Page 20
DSGPULW DUOSCREED — APPLICATION/OPERATION 13. Repeat steps 9 through 12 pulling the DuoScreed from the edge of the grid's top right corner, horizontally toward the center. 14. Remember to build the bases in long parallel strips across the pins and on the hand floated edges and against plumbing or other outs, leaving the long unfin- ished areas about 8 or 9 feet wide.
Page 21
DSGPULW DUOSCREED — APPLICATION/OPERATION 12-18 INCH 12-18 INCH BASE BASE TOP LEFT TOP RIGHT CORNER OF CORNER OF GRID GRID STEP 7 DUOSCREED BLADE STEP 7 HORIZONTAL HORIZONTAL DIRECTION DIRECTION VERTICAL STEP 1 DIRECTION PLACE # 5 REBAR GRADE PINS STEP 7 AND FORM RECTANGULAR GRID.
Page 22
DSGPULW DUOSCREED — APPLICATION/OPERATION ■ When screeding make sure the blade is kept straight. DO Important Tips to Remember NOT let blade turn. ■ Do not allow the engine to run out of fuel as this may cause ■ DO NOT run the DuoScreed with one part of the blade on problems with starting.
DSGPULW DUOSCREED — MAINTENANCE Use a low pressure water hose, soft brush, wiping cloth Maintenance and a mild cleaning detergent and remove all concrete from the DuoScreed. Be careful not to get excessive amounts CAUTION - Pressure Washer of water in the engine compartment. DO NOT clean the DuoScreed with a pressure washer .
Page 24
DSGPULW DUOSCREED — MAINTENANCE Air Cleaner 3. Remove the spark plug with 5/8-inch wrench. 1. The air cleaner element should be cleaned because a Inspect the spark plug. Replace it if the electrodes are worn, clogged air cleaner can cause poor engine starting, lack of or if the insulator is cracked or chipped.
A blank entry generally indicates that the item is not sold assembly/kit that can be purchased, or is not available separately or is not sold by Multiquip. Other entries will for sale through Multiquip. be clarified in the “Remarks” Column.
DSGPULW DUOSCREED — NAME PLATE AND DECALS NAME PLATE AND DECALS. NAMEPLATE BLADE LENGTH ECCENTRIC WEIGHT POSITION FEET METERS 12.3 3.75 13.9 4.25 16.4 5.00 18.0 5.00 19.6 6.00 PAGE 30 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV. #7 (09/19/18)
Page 31
DSGPULW DUOSCREED — NAME PLATE AND DECALS NAME PLATE AND DECALS. PART NO PART NAME QTY. REMARKS DCL121 DECAL, PRESSURE HOSE DCL122 DECAL, SAFETY PLATE, SERIAL NO......1 .... CONTACT MQ PARTS DEPT. W/MODEL & S/N DCL140 DECAL, ALIGNMENT ARROWS ..2 DCL141 DECAL, ECCENTRIC WT.
DSGPULW DUOSCREED — MAIN ASSY. DUO SCREED MAIN ASSY. OLD STYLE CENTRIFUGAL HOUSING NEW STYLE CENTRIFUGAL HOUSING REFERENCE ONLY NOTES OLD STYLE CENTRIFUGAL HOUSING ASSEMBLY NO LONGER AVAILABLE. IF REPLACEMENT OF ITEM 5A IS REQUIRED, ORDER NEW STYLE HOUSING ASSEMBLY, ITEM 86. PAGE 32 —...
Page 33
DSGPULW DUOSCREED — MAIN ASSY. DUO SCREED MAIN ASSY. NO. PART NO. PART NAME QTY. REMARKS BF2648 HANDLE GRIP BF2647 THROTTLE HANDLE BF2633LW UPPER OPERATING HANDLE 2640A35 ENGINE HONDA GX-35SAT CENTRIFUGAL CLUTCH HOUSING CP ... 1 ..NO LONGER AVAILABLE ..................
Page 34
DSGPULW DUOSCREED — MAIN ASSY. DUO SCREED MAIN ASSY. OLD STYLE CENTRIFUGAL HOUSING NEW STYLE CENTRIFUGAL HOUSING REFERENCE ONLY NOTES OLD STYLE CENTRIFUGAL HOUSING ASSEMBLY NO LONGER AVAILABLE. IF REPLACEMENT OF ITEM 5A IS REQUIRED, ORDER NEW STYLE HOUSING ASSEMBLY, ITEM 86. PAGE 34 —...
Page 35
DSGPULW DUOSCREED — MAIN ASSY. DUO SCREED MAIN ASSY. PART NO. PART NAME QTY. REMARKS BF0175 RETAINING RING M12 BF2615A ECCENTRIC PLATE (SMALL) BF2615B ECCENTRIC PLATE (BIG) BF0207 COUNTERSUNK HEADSCREW 8.8 M8X25 BF2617 PLASTIC PROTECTION CAP M12 BF2607 COMPRESSION SPRING FOR CLAMPING STRIP BF2605LW ALUMINUM CLAMPING STRIP BF0176...
HONDA GX35SAT ENGINE — FAN COVER AND CLUTCH ASSY. FAN COVER AND CLUTCH ASSY. PAGE 48 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV. #7 (09/19/18)
Page 49
HONDA GX35SAT ENGINE — FAN COVER AND CLUTCH ASSY. FAN COVER AND CLUTCH ASSY. PART NO. PART NAME QTY. REMARKS 19611Z0Z000 COVER, FAN 22000ZM5003 CLUTCH ASSY. 22253ZM5003 BOLT, CLUTCH 8MM 22254ZM5003 WASHER, CLUTCH 8X17 90009Z0H003 BOLT, SOCKET 5X20 DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV. # 7 (09/19/18) — PAGE 49...
HONDA GX35SAT ENGINE — FUEL TANK ASSY. FUEL TANK ASSY. PAGE 54 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV. #7 (09/19/18)
Page 55
HONDA GX35SAT ENGINE — FUEL TANK ASSY. FUEL TANK ASSY. PART NO. PART NAME QTY. REMARKS 17504ZM3003 GROMMET FUEL TUBE 17511Z0Z003 TANK, FUEL 17533Z0H000 RUBBER, TANK MOUNTING 17555Z0Z000 GUARD, TANK ........1... INCLUDES ITEMS W/ 17620ZM3043 CAP ASSY., FUEL TANK 17672ZM3003 FILTER, FUEL 17701Z0Z000...
HONDA GX35SAT ENGINE — ENGINE TOP COVER ASSY. ENGINE TOP COVER ASSY. PAGE 58 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV. #7 (09/19/18)
Page 59
HONDA GX35SAT ENGINE — ENGINE TOP COVER ASSY. ENGINE TOP COVER ASSY. PART NO. PART NAME QTY. REMARKS 19720Z0Z000ZA COVER, TOP *R280* POWER RED 90015Z0H003 BOLT, TOP COVER DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV. # 7 (09/19/18) — PAGE 59...