Table of Contents
Advertisement
Quick Links
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
SANTA FE PELLET INSERT
APPLIANCE
MODEL: SANTAFEI-MBK
CAUTION
Check building codes prior to installation.
•
Installation MUST comply with local, regional, state
and national codes and regulations.
•
Consult local building, fire officials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
1
Installation Manual
Installation & Appliance Set-Up
NOTICE: DO NOT DISCARD THIS MANUAL
If the information in these instructions is
not followed exactly, a fire could result
causing property damage, personal injury,
or death.
•
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
•
Do not over fire - If appliance or chimney connector
glows, you are over firing. Over firing will void your
warranty.
•
Comply with all minimum clearances to combustibles
as specified. Failure to comply may cause house fire.
•
Do not touch glass until it is cooled
•
NEVER allow children to touch glass
•
Keep children away
•
CAREFULLY SUPERVISE children in same room as
fireplace.
•
Alert children and adults to hazards of high
temperatures
•
High temperatures may ignite clothing or other
flammable materials.
•
Keep clothing, furniture, draperies and other
flammable materials away.
Tested and approved for wood pellets and corn pellets.
Burning of any other type of fuel voids your warranty.
To obtain a French translation of this manual, please contact
your dealer or visit
Pour obtenir une traduction française de ce manuel, s'il vous
plaît contacter votre revendeur ou visitez
7019-230J
WARNING
WARNING
HOT SURFACES!
Glass and other surfaces are hot
during operation AND cool down.
Hot glass will cause burns.
CAUTION
NOTE
www.quadrafire.com
www.quadrafire.com
October 23, 2018
Advertisement
Table of Contents
Related Manuals for Quadra-Fire Santa Fe Pellet Insert
Summary of Contents for Quadra-Fire Santa Fe Pellet Insert
- Page 1 OWNER: Retain this manual for future reference. NOTICE: DO NOT DISCARD THIS MANUAL WARNING If the information in these instructions is SANTA FE PELLET INSERT not followed exactly, a fire could result causing property damage, personal injury, APPLIANCE or death.
-
Page 2: Table Of Contents
B. Accessory List ......29 Quadra-Fire is a registered trademark of Hearth & Home Technologies. -
Page 3: Important Safety Information
NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the ASTM E1509-2004, ULC S628-93, ULC/ORD-C-1482-M1990, (UM) 84-HUD The Quadra-Fire Santa Fe Pellet Insert meets the U.S. Environmental Protection Agency’s emission limits for pellet inserts sold after May 15, 2015. -
Page 4: Glass Specifications
SANTA FE PELLET INSERT C. Glass Specifications WARNING This appliance is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please Fire Risk. contact your dealer for replacement glass. Hearth & Home Technologies disclaims any D. Electrical Rating responsibility for, and the warranty will be 115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps... -
Page 5: Getting Started
SANTA FE PELLET INSERT Install Guide Getting Started A. Design, Installation & Location Considerations Since pellet exhaust can contain ash, soot or sparks, you must consider the location of: 1. Appliance Location • Windows • Air Intakes NOTICE: Check building codes prior to installation. -
Page 6: Thermostat Wall Control Location
SANTA FE PELLET INSERT B. Thermostat Wall Control Location WARNING The thermostat wall control’s location will have some affect on the appliance’s operation. Fire Risk. • Maximum wire length from appliance is 100 feet Damaged parts could impair safe operation. Do (30.48m) continuous non-spliced wire. -
Page 7: Install Checklist
SANTA FE PELLET INSERT E. Install Checklist ATTENTION INSTALLER: Follow this Standard Work Checklist This standard work checklist is to be used by the installer in conjuction with, not istead of, the instructions contained in this installation manual. _________________________________________________________________________________ Customer:... -
Page 8: Dimensions And Clearances
SANTA FE PELLET INSERT Dimensions and Clearances A. Appliance Dimensions 28-7/8 in [732mm] 23-5/8 in [600mm] 8 in [203mm] 23 in [584mm] 12-3/4 in 11-1/8 in 25-3/8 in 9-5/8 in [325mm] [283mm] [644mm] [246mm] 17-7/8 in [453mm] 9-1/2 in [243mm]... - Page 9 SANTA FE PELLET INSERT B. Clearance To Combustibles, UL and ULC 25 in.** 25 in.** (635mm) (635mm) 32-7/8 in. (835mm) 15-1/4 in.* Be sure to follow vent manufacturers clearance to (387mm) combustibles. *If interior of chase will be drywalled, add the thickness to this measurement.
-
Page 10: Minimum Opening For Masonry & Zero Clearance
SANTA FE PELLET INSERT C. Minimum Opening for Masonry & Zero Clearance Fireplaces TOP TRIM 26-3/4 in 20-3/4 in (679mm) (527mm) 29-3/4 in (1010mm) 16 in HEARTH (406mm) EXTENSION Figure 10.3 Figure 10.1 NOTE: If trim measurement is over 3/4 in (19mm) in depth... -
Page 11: Installation Into A Factory-Built Fireplace
SANTA FE PELLET INSERT F. Installation into a Factory-Built Fireplace The following is only one example as there are many different models of factory-built fireplaces. The following modifications are permissible: • Removal of damper or locked in open position NOTE: This example is for reference only. Any •... -
Page 12: Installation Into A Masonry Fireplace
SANTA FE PELLET INSERT G. Installation into a Masonry Fireplace WARNING All modifications that can be made to a Factory Built Fireplace can be made to a Masonry Fireplace. Risk of Fire! Follow venting manufacturer’s clearances and In addition DO NOT remove any brick or mortar from the instructions when installing venting system. -
Page 13: Vent Information
SANTA FE PELLET INSERT Vent Information A. Venting Termination Minimum Requirements Electrical Service Inside Corner FIXED FIXED OPEN CLOSED CLOSED OPEN J or K Figure 13.1 Termination Cap Air Supply Inlet Restricted Area Gas Meter All minimum clearances are listed with an Outside Air Kit (OAK) installed, unless otherwise noted in table below. -
Page 14: Avoiding Smoke And Odors
SANTA FE PELLET INSERT B. Avoiding Smoke and Odors • Power outages during operation will cause the appliance to immediately turn off and may create Negative Pressure, Shut-Down and Electrical Power conditions where smoke will back draft into the house. -
Page 15: Draft
3 to 6 inch (76-152mm) Top Vent Offset Adapter, • Location of the vent termination must not obstruct use Listed double wall flue connector. A Quadra-Fire or interfere with access to the electrical service. Outside Air Kit must be used with manufactured home installations. -
Page 16: Equivalent Feet Of Pipe
SANTA FE PELLET INSERT G. Equivalent Feet of Pipe WARNING The table below can help you calculate the equivalent feet of pipe which is a method used to determine pellet vent Vent surfaces get HOT, can cause burns size (Figure 15.1). -
Page 17: Venting Systems
SANTA FE PELLET INSERT Venting Systems A. Full Reline With Outside Air - Horizontal CAUTION WARNING Fire Risk. Never draw outside combustion air from: • Wall, floor or ceiling cavity Inspection of Chimney: • Enclosed space such as an attic or garage •... -
Page 18: Full Reline With Outside Air - Vertical
SANTA FE PELLET INSERT B. Full Reline With Outside Air - Vertical NOTE: Check clearances carefully for this type of installation to ensure adequate room for outside 12” (305mm) min. above air venting. 12” (305mm) min. below CAUTION Check building codes prior to installation. -
Page 19: Appliance Set-Up
SANTA FE PELLET INSERT Appliance Set-Up A. Leveling System B. Outside Air Kit Instructions The leveling bolts are located at the rear of the appliance. Parts Included in Kit: 1 piece of 2 inch x 3 ft. flex hose, To access the bolts, remove the front access panels. -
Page 20: Optional Grille Removal And Installation
SANTA FE PELLET INSERT C. Optional Grille Removal and Installation 5. The upper grille has 2 separate parts. Install the 3 grilles attached together first. Angle the grilles Included in Kit: (4) lower grilles; (3) upper grilles, (1) downward and insert the heat exchanger cleaning rods upper grille;... -
Page 21: Adjustable Hearth Support
SANTA FE PELLET INSERT F. Adjustable Hearth Support Size: 9”d x 45”w, 2” to 10” Height Adjustment EXPLODED VIEW OF SCISSORS Included in Kit: (1) trim top, (1) trim front, (2) trim sides, double-sided tape (already installed) Tools Needed: Phillips head screwdriver, sheet metal... -
Page 22: Panel And Trim Set
SANTA FE PELLET INSERT G. Panel and Trim Set Open Hopper Lid for 1. Lay panel top and legs face down on protective Easier Placement of covering to prevent scratching. Panel Set 2. Attach the panel legs to the top panel using a Phillips Magnet head screwdriver. -
Page 23: Thermostat Installation
SANTA FE PELLET INSERT H. Thermostat Installation 1. Separate the body of the thermostat from the mounting plate by gently pulling the two pieces apart (Figure The kit comes with a programmable wall thermostat and 23.1) 25’ of thermostat wire. If you need to run more than 25’... -
Page 24: Optional Log Set Placement
SANTA FE PELLET INSERT CONNECT THERMOSTAT WIRES TO APPLIANCE: I. Optional Log Set Placement There is a 4 screw terminal block located on the back lower Two Piece Log Set Installation left corner of the stove directly above the power cord inlet. -
Page 25: Mobile Home Installation
SANTA FE PELLET INSERT Mobile Home Installation You must use a Quadra-Fire Outside Air Kit for CAUTION installation in a mobile home. THE STRUCTURAL INTEGRITY OF THE MOBILE 1. An outside air inlet must be provided for the HOME FLOOR, WALL AND CEILING/ROOF MUST BE... -
Page 26: Reference Materials
SANTA FE PELLET INSERT Reference Materials A. Service & Maintenance List Date of Service Performed By Description of Service 7019-230J October 23, 2018... - Page 27 SANTA FE PELLET INSERT Date of Service Performed By Description of Service October 23, 2018 7019-230J...
-
Page 28: Accessory List
SANTAFEI-MBK Service Parts Beginning Manufacturing Date: Dec. 2009 SANTA FE PELLET INSERT Ending Manufacturing Date: Active B. Accessory List IMPORTANT: THIS IS DATED INFORMATION . Parts must be ordered from a dealer or SANTAFEI-MBK Hearth and Home Technologies does not sell directly to consumers Service Parts distributor. - Page 29 SANTA FE PELLET INSERT SANTAFEI-MBK Service Parts Beginning Manufacturing Date: Dec. 2009 Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION . Parts must be ordered from a dealer or Hearth and Home Technologies does not sell directly to consumers distributor.
- Page 30 Hearth & Home Technologies 352 Mountain House Road Halifax, PA 17032 Division of HNI INDUSTRIES Please contact your Quadra-Fire dealer with any questions or concerns. For the number of your nearest Quadra-Fire dealer log onto www.quadrafire.com CAUTION DO NOT DISCARD THIS MANUAL...