1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Monitor
  5. VRR P10
  6. Product manual

Samsung VRR P10 Product Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Product Manual
VRR P10
1 / 50

Advertisement

Table of Contents
loading

Related Manuals for Samsung VRR P10

Summary of Contents for Samsung VRR P10

  • Page 1 Product Manual VRR P10 1 / 50...

  • Page 2: Table Of Contents

    Chapter 6 VRR P10 Installation Process............12 6.1 Power Cable Connection..............12 6.2 Signal Cable Connection..............13 Chapter 7 VRR P10 Displaying Controller Set-up Steps........14 7.1 Nova Lct-Mars Control System Instruction........14 Appendix A Dimensional Drawing of Main Components........18 Appendix B VRR P10 Specification Table............

  • Page 3: Chapter 1 Vrr P10 Product Brief

    Dear users, you are welcome to use Samsung products. We are very pleased if this manual is helpful for you. This manual is intended to provide you with an installation instruction. If you encounter any problems during usage, or if you have any suggestions, please contact us according to the contact information in the manual, We will try our best to solve this problem.

  • Page 4: Chapter 2 Safety

    Before installing the VRR P10, please ensure that you understand and follow the safety guidelines, safety instructions and warnings in this section. In this manual, the “VRR P10” contains the following products from the company: Outdoor Use: VRR P10. 2.1 Safety Guidelines Personal Protection：...

  • Page 5: Safety Statement

    VRR P10; Please follow the assembly instructions when installing the cabinet. If you  encounter any problems during the installation, please contact Samsung in time. Product Care The cabinet should be kept dry and clean. It is recommended that users conduct ...

  • Page 6: Instructions For Use

    Since the display LED lamps of the VRR P10 are relatively fragile, do not collide  the surface with hard and sharp objects to prevent damage to the lamp body.
  • Page 7 The voltage and power of the power supply equipment of the VRR P10 must  meet the requirements. When the VRR P10 products are not used for a long time, please cut off the  power supply to avoid a safety accident.

  • Page 8: Chapter 3 Vrr P10 Product Installation Requirements

    Chapter 3 VRR P10 Product Installation Requirements This chapter introduces the basic requirements for the installation of the VRR P10, including structural requirements, electrical requirements, and computer system requirements. 3.1 Structure Requirements Ground requirements: The installation position of the display screen requires flat ...

  • Page 9: Chapter 4 Displaying System

    Chapter 4 Displaying System This chapter mainly introduces the displaying system connection diagram of the VRR P10 products, and introduces the main accessories of display screen. 4.1 Displaying System Connection Diagram 1. Sending box---send video data to the display; 2. USB serial cable---Communicate with computer, set the sending box parameters through software;...

  • Page 10: Chapter 5 Vrr P10 Installation

    Chapter 5 VRR P10 Installation This chapter mainly introduces the installation process of VRR P10 HD products and guides customers to install the products correctly. 5.1 Rotary Single Leg Introduction A. Single leg and Cabinet: 0 Degree B. Single leg and Cabinet: Rotating to 90 Degree...

  • Page 11: Cabinets Alignment

    C. Single leg and Cabinet: 90 Degree 5.2 Cabinets Alignment Align the two cabinets horizontally and lock the two latches with a hex driver to complete the splicing. 11 / 50...

  • Page 12: Chapter 6 Vrr P10 Installation Process

    The maximum current of the aviation head used on the VRR P10 product cabinet is 20A. To avoid the safety problems such as overheating and fire, the total current of the cascaded main power supply must be <20*0.8=16A, VRR P10 The display...

  • Page 13: Signal Cable Connection

    3. After the cabinet is installed, connect the signal wires according to the design drawings. Figure 6-2 shows the connection of signal lines in the arrangement of VRR P10 1*46. Each main network cable carries 128*96*46=565,248 pixels. In the figure: ①...

  • Page 14: Chapter 7 Vrr P10 Displaying Controller Set-Up Steps

    Drawing connections. Chapter 7 VRR P10 Displaying Controller Set-up Steps This chapter mainly introduces the setup steps of the VRR P10 product control software. 7.1 Nova LCT-Mars Control System Instruction 7.1.1 Load display profile...
  • Page 15 A password window pops up, as shown in Picture 7-2. Enter the password “666” to pop up the parameter setting window, as shown in Picture 7-2. Click the “Confirm” button on the Screen Config interface, as shown in Picture 7-2. Picture 7-2 Click the “load files”...
  • Page 16 Picture 7-4 Picture 7-5 Note: Do not modify any parameters after the non-professionals load the "*.rcfgx" file. If the parameters are inadvertently modified, the display screen will not display properly. The configuration file needs to be reloaded and sent to the receiving card. After sending and saving the configuration file, the display should display the same content in units of the cabinet.
  • Page 17 7.1.2 Screen connection file loading Click "Load from File" in the "Screen connection" interface of the software parameter settings. Load the “*.scr” file, then click the “Send to HW” button. After the display shows normal, click “Save”, as shown in Picture 7-6, Picture 7-7. Picture 7-6 Picture 7-7 Note: Do not modify any parameters after non-professionals load the "*.scr"...

  • Page 18: Appendix A Dimensional Drawing Of Main Components

    Appendix A Dimensional Drawing of Main Components A.1 VRR P10 Cabinet Size A.2 Dolly (5 in 1) 18 / 50...
  • Page 19 A.3 Flight Case(2 in 1) 19 / 50...

  • Page 20: Appendix B Vrr P10 Specification Table

    Appendix B VRR P10 Specification Table Product Name VRR P10 Physical Pitch 10 mm LED Vendor Nationstar LED Package Name RS-3535MWAR Size of LED color bin combination R:5nm, G:3nm, B:3nm No. of LED Bin for 1 project Single Bin D-IC Vendor...
  • Page 21 Packaging Weight 90.5 kg/pcs Packaging Method (Flight Case) 2 in 1 Packaging Dimensions (W × H × D) 1380x1198x461mm Packaging Weight Brightness (after Cal.) ≥ 6,000 nits Refresh Rate 3,840 Hz Horizontal Viewing Angle 160° Vertical Viewing Angle 120° Color temperature Optical/ Video - Default...
  • Page 22 Accessory List Items Specs Remark Module 202100000055R Module 320*320MM 320*320MM Receiver card 205020200018R Receiver MRV410 card MRV410 Power supply 115309258006R Power AP196A AP196A 204100000039B HUB board-L board-L 204100000040B HUB board-R board-R Power signal 214030000029R Power cable A 0.38m signal cable A 0.38m Power signal 214030000030R...
  • Page 23 Power jumper 208030200230R Power cable 0.85M cable 0.85M (SEETRONIC (SEETRONIC outdoor) outdoor) Power jumper 208030200231R Power cable 1.25M cable 1.25M (SEETRONIC (SEETRONIC outdoor) outdoor) Signal jumper 209020200049R Signal cable 0.9M cable 0.9M (SEETRONIC (SEETRONIC outdoor) outdoor) Main power cable 208030100103R Main (SEETRONIC power...
  • Page 24 Master IC NXP 110902H24521R Master IC 74HC245PW NXP 74HC245PW Screw 120300604004R Screw PA1.7*8 PA1.7*8 Power 120500207012R Power aviation female aviation female head head SAC3FX SAC3FX Power 120500207013R Power aviation male aviation male head head SAC3MX SAC3MX Signal aviation 120500407026R Signal head aviation head SE8MC-05 SE8MC-05...

  • Page 25: Appendix C Tools To Be Prepared

    Appendix C Tools to be prepared C.1 Adjustable Wrench (conventional) C.2 Screwdriver (medium size) C.3 Allen key (M3 is used to open the power cabinet, M8 is used to fix the connecting piece) C.4 Rotating key 25 / 50...

  • Page 26: Appendix D Common Troubleshooting Methods

    Appendix D common troubleshooting methods A. The whole screen does not light or flash: 1. Check if the power is energized. As shown in Figure D-1 below: Picture 1 2. Check if the DVI cable the signal cable are in good contact or not. As shown in Picture 2 below 3.
  • Page 27 B. Module Failure： 1. The single lamp has no light, and the LED itself is damaged, resulting in a dead lamp. As shown in Picture 4: Picture 4 2. A string of lamps are not lit or constantly lit: one of the 16-bit pins of the constant current IC is damaged or in pseudo soldering.
  • Page 28 4. If a module is not lit, the socket of the module may be too loose to be powered. (As shown in Picture 7) cture 7 5. If one or several lines of the module are not lit, the tube may be damaged. 6.

  • Page 29: Appendix E Common Maintenance And Disassembly Methods

    Appendix E Common Maintenance and Disassembly Methods 1.1 Removal of the front maintenance module A. Insert the front maintenance tool into the front maintenance maintenance mounting hole of the four modules as shown in the figure, see Figure E-1 below, and then rotate °...
  • Page 30 Pic E-2 B.Pull out the module, see Pic E-3 Pic E-3 The principle of the Pic is as follows: first insert the module front maintenance tool into the rotary lock cylinder in the module, as shown below Pic E-4, then rotate the front maintenance tool 90 °...
  • Page 31 Pic E-4 Pic E-5 1.2 Module maintenance and maintenance: A. Insert the M3 Allen key into the four rear maintenance tool holes on the back of the module and rotate it 90° to the right. See Pic E-6 Pic E-6 B.
  • Page 32 （Turn Left） （Pull out） Pic E-7 1.3 Dis-assembly of the power supply box A. Remove the power box, first loosen the lock under the power box, see Pic E-8 Pic E-8 B. Lift the power supply box up and remove it later to remove the power supply box. See Pic E-9 steps.
  • Page 33 Step Pic (from left to right) 33 / 50...
  • Page 34 1.4 Disassembly and maintenance of power supply and receiving card First step, repair receiving card: A After removing the power supply box, loosen the screws on the cover. See Pic E-10 Pic E-10 B First remove the receiving card cable and the current sharing cable, and remove the power cable.
  • Page 35 Pic E-12 35 / 50...
  • Page 36 The second step is to repair the power supply: C Remove the four screws on the power back plane. See Pic E-13 Pic E-13 D Remove the line above the power supply, see step Pic E-14 36 / 50...
  • Page 37 Pic E-14 1.5 Left and right connection board maintenance A first remove the 2+9 air socket fixing nut on the power box with a wrench, see step Pic E-15 (1. First loosen the fixing nut) （2. Remove the retaining ring） 3.
  • Page 38 5. Remove the screws that secure the wire Pic E-15 1.6 LCD panel maintenance A first remove the cable and screws next to it, see step Pic E-16 （First remove the network cable） Remove the fixed screws 38 / 50...
  • Page 39 Remove the LCD cover directly and remove the internal screws Direct replacement Pic E-16 1.7 Empty open box internal maintenance (the same way as the power supply box is removed from the cabinet) A first remove the screws on the empty box, see Pic E-17 39 / 50...
  • Page 40 Pic E-17 B leakage switch maintenance, first remove the screws for fixing on the empty open box, see Pic E-18 Pic E-18 C First remove the screws at both ends of the upper cover of the leakage switch, and then remove the screws that fix the wire on the switch. See step Pic E-19 40 / 50...
  • Page 41 Pic E-19 For D terminal block maintenance, first remove the screws that fix the cover, and then remove the screws on the fixed and empty open boxes. Finally remove the wire screws. See step Pic E-20 Pic E-20 41 / 50...

  • Page 42: Appendix F Stadium Screen Packaging Transportation

    Appendix F Stadium Screen Packaging Transportation 1. The composition of the stadium screen transport bracket, see Pic F-1 Top Cover*1 Left & Right Support Frame*2 Base*1 Pic F-1（5 in 1） 2 Remove the top cover and left and right supports of the trailer: 2-a.
  • Page 43 Pic F-2 Pic F-3 43 / 50...
  • Page 44 Pic F-4 Pic F-5 Pic F-6（Left and right support frame and base hinge joint） 3 Install the stadium screen cabinet into the trailer: 3-a. Rotate the bottom of the stadium screen by 90° to receive the bottom of the cabinet, see Pic F-7; 44 / 50...
  • Page 45 3-b. Match the module surface with the direction of the arrow of the trailer. See Pic F-8. Lift the cabinet into the middle of the trailer through the handles on both sides of the cabinet, and locate the positioning hole and trailer of the cabinet. Pin, put on the trailer, see Pic F-9;...
  • Page 46 Front Lamp Surface Trailer silk screen Pic F-8 Cabinet Location Hole Dolly Location Pin 46 / 50...
  • Page 47 Pic F-9 4 Assembly trailer left and right support: 4-a. Align the left and right supports with the pin holes of the base, see Pic F-10, and force the left and right supports in the direction to make the hinge holes fit tightly, see Pic F-11;...
  • Page 48 Pic F-12 Pic F-13 Pic F-14 5 Assemble the top cover of the trailer: 5-a. The direction of the upper cover silk screen should be consistent with the direction on the trailer, see Pic F-15; 5-b. Align the positioning pin of the upper cover with the positioning hole on the left and right supports, see Pic F-16;...
  • Page 49 Direction Indicator Direction Indicator Pic F-15 Pic F-16 6 After pushing the trailer to the destination and stepping on the diagonal brake, you can move smoothly. If you want the tow wheel to rotate, you can step on 49 / 50...
  • Page 50 the other side of the brake, see Pic F-17; Pic F-17 50 / 50...

Table of Contents