Denon DVP-602CI Service Manual page 25

Pin Pin Name Symbol
71 P21/AN21/A1 -
72 P20/AN20/A0 -
73 P17/INT5/D15 PROTECTION
74 P16/INT4/D14 ERESET
75 P15/INT3/D13 REMOTEDET
76 P14/D12 -
77 P13/D11 -
78 P12/D10 -
79 P11/D9 -
80 P10/D8 -
81 P07/AN07/D7 -
82 P06/AN06/D6 -
83 P05/AN05/D5 -
84 P04/AN04/D4 -
85 P03/AN03/D3 FL_CLK
86 P02/AN02/D2 FL_DATA
87 P01/AN01/D1 FL_CE1
88 P00/AN00/D0 FL_RST
89 P107/AN7/KI3 -
90 P106/AN6/KI2 GRNLED
91 P105/AN5/KI1 REDLED
92 P104/AN4/KI0 -
93 P103/AN3 KEY3
94 P102/AN2 KEY2
95 P101/AN1 KEY1
96 AVSS AVSS
97 P100/AN0 MODE
98 VREF MASTER5V
99 AVCC AVCC
100 P97/ADTRG/RXD4 RSTSUB
Note: Pin No. : Terminal number of microcomputer.
Port Name : The name entered in the data sheet of microcomputer.
Symbol : Symbolized interface function.
I/O : Input or out of part.
"I"
"O"
Type : Composition of port in case of output port.
"C"
"N"
"P"
Op : Pull up/Pull down selection information.
"Iu"
"Id"
"Eu"
"Ed"
Det : Indicates judging state of input port. Level detection is "LV"; Edge detection is "Ed"; Detection by both shifting is "E&L";
Serial data detection is "S" (Serial data output is also "S").
Res : State at reset.
"H"
"L"
"Z"
STBY : State of port when STANDBY mode.
"O/L" = Output port and "L"
"I"
Stop : State of port when Stop mode.
"O/L" = Output port and "L"
"I"
I/O Type Det
O C −
O C −
I C Lv
O − −
I − E ↓ &H
I − −
I − −
I C −
I C −
I C −
I C −
I − −
I C −
I C −
O C −
O C −
O C −
O C −
I − −
O − −
O C −
I C E ↓ &H
I − Lv
I − Lv
I − Lv
− − −
I − Lv
− − −
− − −
O − −
= Input port
= Output port
= CMOS output
= NMOS open drain output
= PMOS open drain output
= Inner microcomputer pull up
= Inner microcomputer pull down
= External microcomputer pull up
= External microcomputer pull down
= Outputs High Level at reset
= Outputs Low Level at reset
= Becomes High impedance mode at reset
= Input port
= Input port
DVP-602CI
VCC Op(Ext.) Res STBY stop
− Ed Z O/L O/L
− Ed Z O/L O/L
5V Eu Z I I
3.3V Ed Z O/L O/L
5V − Z I I
− Ed Z O/L O/L
− Ed Z O/L O/L
− Ed Z O/L O/L
− Ed Z O/L O/L
− Ed Z O/L O/L
− Ed Z O/L O/L
− Ed Z O/L O/L
− Ed Z O/L O/L
− Ed Z O/L O/L
5V − Z O/L O/L
5V − Z O/L O/L
5V − Z O/L O/L
5V − Z O/L O/L
− Ed Z O/L O/L
5V Ed Z O/L O/H
5V Ed Z O/L O/H
5V Eu Z I I
5V Eu Z O/L O/L
5V Eu Z O/L O/L
5V Eu Z O/L O/L
− − − − −
5V − Z I O/L
5V − − − −
− − − − −
5V Ed Z O/L O/L
25
Function
−
−
PROTECTION detect pin
ETHERNET comm. control pin
ROOM TO ROOM Signal detect pin (Detected : H)
−
−
−
−
−
−
−
−
−
FL DRIVER control pin
FL DRIVER control pin
FL DRIVER control pin
FL DRIVER control pin
−
POWER/STANDBY LED control pin (ON : H)
POWER/STANDBY LED control pin (ON : H)
−
Button input3
Button input2
Button input1
AVSS
Destination switching input
Ref. power supply input +5V
AVCC
SUB-μcom reset output