Setting The Electronic Shutter - Sony HXC-FB80 Operating Instructions Manual

For example, if one position is disabled, then that position is not
displayed and the button switches between the remaining three
positions.
4
Repeat steps 2 and 3 as required.
5
Assign the CC filter switching function (ELECTRICAL
CC) to a button on the <SWITCH ASSIGN1> page in the
OPERATION menu.
For the ASSIGN 1/2/3 buttons, select ASSIGNABLE 1/2/3 and
set to ELECTRICAL CC. For the COLOR TEMP. button,
select ASSIGN CTEMP and set to ELECTRICAL CC.
White balance memory
There are two white balance memories: A and B. When you execute
automatic white balance adjustment, the adjusted white balance
value is stored in the memory (A or B) selected with the WHITE
BAL switch.
The white balance values stored in memory are retained until the
white balance is adjusted again, including when power is turned off.
When power is turned on again, the white balance in memory
corresponding to the current WHITE BAL switch setting is loaded.

Setting the Electronic Shutter

Note
When connected to a camera control unit or external control device (for
example, RCP or RM), the electronic shutter settings are controlled from the
connected device. They are not controlled using the camera.
For details about operations on the external control device, refer to
the operating instructions or operation manual for the device.
Shutter modes
The shutter modes that can be used with the electronic shutter and
the shutter speeds that can be selected are listed below.
Standard mode
Select this mode for shooting fast-moving subjects with little
blurring.
System frequency Shutter speed (sec.)
• 59.94i 1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000
• 59.94P
• 50i 1/60, 1/125, 1/250, 1/500, 1/1000, 1/2000
• 50P
• 29.97PsF 1/40, 1/60, 1/100, 1/120, 1/125, 1/250, 1/500,
1/1000, 1/2000
• 25PsF 1/33, 1/50, 1/100, 1/125, 1/250, 1/500, 1/1000,
1/2000
• 23.98PsF 1/32, 1/48, 1/96, 1/100, 1/125, 1/250, 1/500,
1/1000, 1/2000
ECS (Extended Clear Scan) mode
Select this mode for obtaining images with no horizontal bands of
noise when shooting subjects such as monitor screens.
SYSTEM LINE System frequency
1080 59.94i
59.94P
50i
50P
29.97PsF
25PsF
23.98PsF
720 59.94P
50P
SLS (Slow Shutter) mode
Select this mode to shoot dimly lit subjects.
You can set the number of accumulated frames to 2, 3, 4, 5, 6, 7, or
8 frames.
Note
In SLS mode, the following limitations apply to automatic functions.
Function
AUTO WHITE
AUTO BLACK
AUTO WHITE SHADING
AUTO BLACK SHADING
AUTO LEVEL
AUTO HUE
AUTO IRIS
ATW
AUTO KNEE
FLARE
D.EXT
TLCS (AUTO SHUTTER)
Setting the shutter mode and shutter speed
Notes
• When automatic iris is used, the iris opens wider as the shutter speed
increases, reducing the depth of field.
• The selectable shutter speeds vary depending on the current system
frequency.
Setting the shutter mode and standard mode
shutter speed
Once the shutter speed is selected, it is retained even when the
camera power is turned off.
1
Push the SHUTTER switch from ON to SEL.
The current shutter setting indication appears in the viewfinder
for about three seconds.
Example: SHUTTER: 1/250
2
Before the shutter setting indication disappears, push the
SHUTTER switch to SEL again.
30
Shutter speed (Hz)
60.00 to 4300
59.96 to 4600
50.00 to 4700
50.03 to 4600
30.00 to 2700
25.00 to 2300
24.00 to 2200
59.96 to 4600
50.03 to 4600
Y: Available, N: Not available
Operation in SLS mode
2F 3F/4F/5F/6F/7F/8F
Y Y
Y 2F setting
N N
N N
N N
N N
Y Y
Y Y
Y Y
Y Y
Y Y
Last enabled function takes
precedence