Notice - Taie FY400 Operation Manual

Digital temperature controller
Hide thumbs Also See for FY400:
Table of Contents

Advertisement

1. Notice

Warning
1. Beware of Electric Shock!
2. Once controller is activated, do not touch AC power wiring terminals to avoid electric shock!
3. First to confirm power is OFF, before working on the wiring of controller power supply!
4. Before using this product, please read through this operating manual thoroughly to understand the correct usage based on
the fundamentals of its conten.
5. This product can be used in industrial equipment, working terminal, measurement equipment, but not in life-saving-
related medical equipment.
6. In order to ensure safety even if the temperature controller fails, please set up another alarm system or safety redundancy.
Caution
1. Before the controller transmits power, make sure that the position of the AC power assembly leg is correct. Otherwise,
the controller may be seriously damaged after power transmission is initiated.
2. Before powering on, please confirm whether the power supply voltage is in accordance with the controller's specification
(AC 85~265V or DC 24V.) Otherwise, the controller may be seriously damaged after power transmission is initiated.
3. Check if the wiring is connected to the terminal for the correct terminals (Input, Output.)
4. Please use crimp terminals suitable for M3 screws, as shown below:
3.2mm
5. Do not install the controller in places subject to high-frequency interference, corrosive gases, and high temperature and
humidity (normal working environment: 0 ~ 50°C, 20 ~ 90% RH.)
6. To avoid noise interference, please keep the sensor wiring away from the power cord and the loading power cord.
7. When the thermocouple lead is extended, please use the compensation lead of the corresponding type to this thermocouple.
8. When the RTD lead wire is extended, please use those with lower resistance value. Please use the same wire between the
three Wires.
2. Order Information
Model
Output 1
NFY900(Red/Green light)
FY901(Blue/White light)
PFY900(Program)
FY/FU400
48x48mm
N
F
Y
6
0
0
9
x 6
4
8
m
m
FY700/FU72
72x72mm
FY800/ FU86
48x96mm
FY900/FU96
96x96mm
PFY400 / FU400
48x48mm
PFY600
96x48mm
PFY700 / FU72
72x72mm
PFY800 / FU86
48x96mm
PFY900 / FU96
96x96mm
Boxed-in items are optional functions, which shall incur extra charges.
FY/FU operation manual
3.2mm
Torque : 0.4 N.m (4kgf.cm)
Output 2
Alarm
1
0
1
0
None
0
None
0 None
1
Relay
1
Relay
1 1 Set
2
Voltage Pulse
2
Voltage Pulse
2
2 Sets
(SSR Drive)
(SSR Drive)
3
4~20mA
3
4~20mA
3
3 Sets
4
0~20mA
4
0~20mA
A
0~5V
A
0~5V
B
0~10V
B
0~10V
A
HBA
C
1~5V
C
1~5V
B
HBA+AL2
D
2~10V
D
2~10V
C
HBA+AL2+AL3
1 SCR zero cross control
5
3 SCR zero cross control
6
7
Motor valve control
1 SCR phase angle control
8
TRS
Remote
COMM
0
0
0
0 None
0 None
0 None
1
4~20mA
1
4~20mA
3
TTL
2
0~20mA
2
0~20mA
B
RS-485
A
0~5V
A
0~5V
B
0~10V
B
0~10V
C
1~5V
C
1~5V
D
2~10V
D
2~10V
M
Motor valve
control feedback
※ HBA : Heater Break Alarm(HBA must use AL1 as alarm relay)
Input type
Power
Accessories
0
1
A
N
See
input
A AC 85~265V
N None
Range
type
code
D
DC 24V
T
Terminal Cover
W
IP65
R
Terminal Cover
+IP65
Block means optional functions with additional charge
4

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Fy600Fy700Fu400Fy900Fu48Fu86 ... Show all

Table of Contents