Zte AC570 User Manual
  1. Manuals
  2. Brands
  3. Zte Manuals
  4. Modem
  5. AC570
  6. User manual
Zte AC570 User Manual

Zte AC570 User Manual

Evdo usb modem
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ZTE AC570
EVDO USB Modem
User Guide
1

Advertisement

Table of Contents
loading

Related Manuals for Zte AC570

Summary of Contents for Zte AC570

  • Page 1 ZTE AC570 EVDO USB Modem User Guide...

  • Page 2: Table Of Contents

    Contents 1 Modem Introduction............4 1.1 Introduction............4 1.2 Warning and Notice ........4 1.3 Applicability Scope ......... 6 1.4 System requirements ........6 1.5 Functions ............6 1.6 Specification............. 7 2 Installation ..............8 2.1 Outline and Part Introduction...... 8 2.2 Software Installation........8 2.3 Hardware Installation ........
  • Page 3 3.4 Phonebook ............26 3.5 Settings ............28 3.5.1 Network Settings...........29 3.5.2 Security Settings............31 3.5.3 Network Settings...........32 3.5.4 Messages Settings ..........33 3.5.5 Alert settings ............33 3.6 Call History............34 3.7 UTK ..............35 3.8 GPS ..............35 3.8.1 Get Position............35 3.8.2 User Settings ............37 3.8.3 Restore Default............37 4 FAQ &...

  • Page 4: Modem Introduction

    We reserve the right to update the technical specifications in this document at any time without prior notice. The ZTE CDMA2000 1X/EVDO USB Modem is a type modem suitable for CDMA network. It adopts USB interface which provides an easy insert to notebook PC.
  • Page 5 injury if used as a toy. Modem Please use original accessories or accessories that are authorized. Using any unauthorized accessories may affect your modem’s performance, and violate related national regulations about telecom terminals. Avoid using the modem near metallic structure device or establishment that can emit electromagnet wave.

  • Page 6: Applicability Scope

    communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.

  • Page 7: Specification

    1.6 Specification Networks CDMA 2000 1x / EVDO CDMA 800MHz Cellular (UL824~849,DL869~894) Frequency CDMA 1900MHz PCS (UL1850~1910,DL1930~1990) Band Dimension 90.4mm*35mm*12.3mm Weight About 35.2g Data Rate Up to 3.1Mbps Working 5V（Using the notebook PC power supply） Voltage...

  • Page 8: Installation

    2 Installation 2.1 Outline and Part Introduction 1. USB Interface 2. UIM Card Slot 3. Indicator 4. Antenna Indicator Light Status: Indicator Status Green/Lighting Normal. Abnormal/No network signal. Green/Blink An Incoming Call. Green/Blink three times A New Message. 2.2 Software Installation The system will automatically detect and recognize the new hardware and display the new icon in the desktop status bar, indicating that the computer and the USB Modem have been connected properly.
  • Page 9 If the notebook PC doesn’t support automatic installation, you can run the installation program in path of My Computer → ZTEMODEM → AutoRun.exe. The following installation interface will show how to start installation. Select PENDRIVE, use the modem as U-Disk. Select MODEM, go to next step.
  • Page 10 Read the agreement carefully. If you agree, choose “I agree to the terms of this license agreement”, and then click “Next”. Select the folder that you want to install the software. You can select a different path by pressing “Change”, and then click “Next”.
  • Page 11 Installation is in progress, after a while, there will be a tip as follows: Click “Finish” to finish the software installation. Note：If you have problems with installation after the upper operation, please...

  • Page 12: Hardware Installation

    After the installation, select “Start” menu → “Programs” and there will be a “ZTE Mobile Connection” program group listed in, which includes “ZTE Mobile Connection” and “ZTE Uninstall”, and a shortcut icon on the desktop is also created.

  • Page 13: Run The Application Software

    2.4 Run the Application Software After the modem is correctly connected, click the Start → Programs→ ZTE Mobile Connection → ZTE Mobile Connection menu on the PC to run the application software. Or double click the shortcut icon on the desktop to run the application software.

  • Page 14: Usb Disk Function

    Click “Yes” according to the indication, then the system begins to uninstall programs, wait a moment and the following screen will appear: Click “Finish” and complete the application software uninstall. 2.7 USB Disk Function You can use your modem as a removable USB disk. When you insert your modem into portable PC, the system will automatically detect and recognize the new hardware.
  • Page 15 Note: if the system doesn’t launch the window automatically, you can run My Computer > ZTEMODEM > AutoRun.exe. Select PENDRIVE icon. The system will install the driver automatically. After a few seconds, a removable disk will appear in My Computer, and then you can use it.

  • Page 16: Functions & Operation

    3 Functions & Operation 3.1 Interface introduction 3.1.1 Main Interface The diagrams drawing for the main interface of USB modem application software: Function Button Area System Information Area User Area The whole interface is divided into three parts, related functions can be executed by operation in the corresponding areas.
  • Page 17 SMS: Send SMS or read SMS Inbox. Phonebook: Save and view different information of the contact list. Settings: Set normal relative information for the modem. Call Records: View related information for all calls. UTK: Supported the service provided by service provider. GPS: Support the GPS service.

  • Page 18: Description Of Mini Icons

    3.1.2 Description of Mini Icons When click the mini button, the software will minimize as an icon on the system tray. If connected to the Internet, the minimized software won’t influence the download of data or receiving SMS. 1. Taskbar Icons’ Description Modem is in normal standby status.

  • Page 19: Connecting Internet

    Modem Offline/ Modem Online: Pause/reusing the working of the modem. If connected Internet, you need disconnect the Internet first, and then select the Modem Offline. Factory Settings: Restore the factory setting. Help: Enter Help interface. About: View the information of the application software and hardware versions. Exit: Close the application interface and stop using the modem.

  • Page 20: Dialing/Answering A Call

    through network. During the course of connecting, when the “Connect” 'button becomes “Disconnect” button, you can cancel the connecting. At the same time, an icon on taskbar appears indicating network connection. Then you can access Internet and receive email etc. via network. 2.
  • Page 21 1. Making a call： Click the number button in the right interface, or enter the phone number by typing the keyboard of computer. Press to erase input character. Press to send and press to end. For international long distance phone call, quick press twice to input international prefix “+”, phone number, quick press in three times to...

  • Page 22: Sms

    4. Redialing： In standby status，press to switch to the dialed calls list, select the number and press and click “Dial” button. 5. Emergency call： Even without UIM card inserting, you still can dial up emergency calls. 6. Dialing up when surfing on the Internet： When surf on Internet, you also can dial up if network supports.

  • Page 23: Read Sms

    InBox: Save the received SMS. OutBox: Save the successfully sent SMS. Draft box: Save the editing SMS, which haven’t been sent. The drafts can only be saved in PC side. For example: “Message in InBox PC :1 Item(s) UIM Card 4 Item(s)” means: The PC side has 1 short message and there are 4 short messages in the Inbox of the UIM card , “UIM Card capability”...

  • Page 24: Create New Message

    3.4.2 Create new message Click “New Message” button to input the recipient’s number and content. The recipient’s number can be input directly or entering the phonebook by pressing The recipient’s amount can be one or more. Please use “;” to separate recipients.
  • Page 25 Select Yes, the SMS will be send, select No, you will go back to previous step to edit the information. After sent successfully, the SMS will be saved into outbox automatically. If send fails, it will be saved to the draft box automatically. Send SMS when browsing the web: When surfing the Internet, if your network supports, you can send short messages.

  • Page 26: The Sms Box Operating Guide

    3.4.3 The SMS box Operating Guide Enter any of Inbox/Outbox/Draftbox to execute the following functions: Read: Read all the information of short messages. (The content of short messages, sender’s phone number, sending time and date) Reply: Reply short messages to the sender (Can’t be executed in OutBox / DraftBox).
  • Page 27 1. New Contact Click “Add” →”New Contact”, input the content, then select “OK” to finish adding a new contact. 2. New Group You can add new groups at the PC side. But you cannot add new groups at the UIM side. Click the “Add”...

  • Page 28: Settings

    3. Other buttons Description If any contact or group is selected, you can carry out the following steps: View: View the information of selected contact. New: Add the new contact. Delete: Delete the selected contacts. SMS: Send messages to the mobile phone numbers in the records. Save As: Save the contacts in PC.

  • Page 29: Network Settings

    3.5.1 Network Settings To ensure that the modem can connect the Internet properly, you should configure the user configuration information first. You can save the different supplier’s network configurations as different files. 1. Button Description Add: Add new configuration files. Delete: Delete the selected configuration files.
  • Page 30 2. Config File The user configuration information includes: Config filename, Dial Number,User name, Password, PDP Type, Authentication Mode, DNS, and PDP address. If network supports “Obtain server address automatically”, the modem can obtain the assigned IP information automatically. If network does not support it, you should input the proper address manually.

  • Page 31: Security Settings

    3.5.2 Security Settings The interface shows as the following picture： 1. Enable the PIN Code When “PIN enable” item is selected, please enter PIN code to use the modem and you can click “Revise PIN” to modify the number. Note: This function need network support. 2.

  • Page 32: Network Settings

    3.5.3 Network Settings Select Mode preference, EVDO+CDMA 1x, CDMA 1X Only, or EVDO Only. For detail information, please consult with your service provider.

  • Page 33: Messages Settings

    3.5.4 Messages Settings Validity period: Set the time limit for saving SMS in the network side. (This function needs network supports.)In option：an hour/12 hours/A day/A week/The longest period. Delivery Report: Set as “Turn On” or “Turn Off”. When it is set as “Turn On”, the network will inform you when you sent messages successfully.

  • Page 34: Call History

    3.6 Call History There are Missed Calls, Received Calls and Dialed Calls in Call History. Select one to enter, you can see the details information. Select one Calls, you can...

  • Page 35: Utk

    Dial: Call the number. SMS: Send messages to the number. Edit: Edit the information of selected number. Delete: Delete the selected number. Clear: Clear all numbers. 3.7 UTK Click UTK icon, switch to the UTK interface. This function needs network support by service provider.
  • Page 36 The modem will make the position and show the results. After finish the position, you can press the Show Map to show the map of your position from Google.

  • Page 37: User Settings

    3.8.2 User Settings Operation Mode Network only: get position results directly via CDMA network and PDE sever. MS-based: firstly get basic position data via CDMA network and PDE sever firstly, then the modem make the calculation and get the position results. Standalone: get the position results not via CDMA network.

  • Page 39: Faq & Answers

    The driver program can the driver program be found in the properly. installation address, e.g. C:\Program Files\ZTE Mobile Connection\drivers After the modem The system Please open the UI is plugged in, the UI configuration is not program manually.
  • Page 40 2．You are in the place 2. Move to the place that where no CDMA has good signal. network covered , such as underground parking lot, tunnel etc. When the USB 1. You have not installed 1. Run the installation modem has been the USB modem program first, then insert plugged in, computer...
  • Page 41 2. The network at this 2. Try later. time in this place is busy now. 3. The modem data is 3. It is perhaps the error. CDMA network problem and please contact with the local supplier timely. Connected to the 1.
  • Page 42 problems.) No warning tone No audio card is fixed in Check the audio card computer or the volume and adjust the volume is too small. properly.

Table of Contents