Table of Contents Introduction ................................3 Know Your Device..............................3 System Requirements ............................4 Technical Specifications ............................. 5 Installation Guide For Windows ........................5 Activation ..............................9 Using The Interface ..........................10 Un-install ..............................18 Troubleshooting ..............................19...
Thank you for choosing AC8720 CDMA2000 1X Wireless USB Modem (hereinafter referred to as USB Modem) of ZTE Corporation The USB Modem equips with a standard USB interface and supports CDMA2000 1X network. In the area where there is signal, it allows you to go surf the Internet, send &...
2. Operation guide of Data Cable Generally, the USB Modem could be directly connected with USB port. You could also connect the USB Modem with PC by using the accompanying data cable, as shown in the following figure. Connect Interface with USB Modem, and interface with PC's USB port. If the power supply from USB port is insufficient, connect both interface and with USB port together.
Technical Standard: CDMA2000 1X USB Interface Standard: USB 2.0 Full Speed Data Rate: 153.6kbps Frequency Band: 800 MHz Dimensions: 91 x 25 x 11 mm Weight: 25g Please connect USB Modem to PC through USB interface. You could use the data cable to ...
Page 6
Select Start Menu folder, and then click “Next”. When you see the window below, please click “Install”. ...
Page 7
Please wait for installation. Please insert the USB Modem into USB interface if the system prompts you to insert the hardware. (If it has been inserted, please unplug it and insert again.) The system shall find the new hardware and install the driver automatically. This may a few minutes.
Page 8
The driver is installed successfully. Pleas click “OK”. Click “Finish” to close the last screen of the wizard. Now you can start running USB Modem application. Note: Please connect the USB Modem and PC with USB extension cable under weak signal to obtain the optimal performance.
After the application is installed successfully, the application icon will appear on your desktop. In order to access internet, please activate the USB modem first. Please click on the icon to activate the modem. The following screen appears. Depending on the choice of service type, choose Prepaid/Postpaid.
After the application is installed successfully, the application icon will appear on your desktop. Double-click this icon or select from Start -> Programs ->(Appropriate Application). Run the application to display the user interface. The icons on the interface are used to access the function, which indicate as below: Open URL Service Voice Call...
Page 11
Click button to directly connect the URL you set in “Settings”. For details on the URL settings, please refer to Chapter “Settings”. Click icon to enter the value-added services such as Google searching. (If this feature is not supported by your USB Modem, please skip over this chapter.) Click to enter Voice Call interface.
Page 12
Please firstly apply for this service from your local telecom operator. During a call, if there is a new incoming call, a pop-up window will prompt you that you have the second incoming call. If you select to answer, please click “Accept waiting call” button. The previous call won’t be ended, but temporarily paused.
Page 13
Statistic Click button to clear the talk duration. (If this feature is not supported by your USB Modem, please skip over this chapter.) Click icon to enter SMS interface. Send a Message 1.Input the text and the recipient’s number. 2.Input the recipient’s number or click button to select the recipient from phonebook.
Page 14
Delete Click to delete your selected records. Clear Click to delete all the records in the inbox. Copy Click to copy your selected record into PC. Copy All Click to copy all the records from the USB Modem to PC. Connect 1.
Page 15
Note:The relevant information contained in connection records are just for user’s reference rather than the charging basis. Delete Connection Records Click button to delete the records you have selected on the interface. Clear Connection Records Click button to delete all the records. (If this feature is not supported by your USB Modem, please skip over this chapter.) Click to view the Phonebook.
Page 16
Copy Click to copy your selected contacts to other storage location. Copy All Click to copy all contacts to other storage location. Import the phonebook Click to import the phonebook (*.txt format) in PC to the terminal. Export the phonebook Click to export the phonebook (*.txt format) in the terminal to PC.
Page 17
If your USB Modem does not support some following functions, please neglect relevant description. Other Settings Click “Options” to switch the interface, and you could set URL and language, etc. If you want to use conference call, please select “Show 3 way call button during calling”; After the setting, click “Apply”...
After the setting, click “Apply” button to save the settings on the current interface. Click “Default” button and then “Apply” button to restore the settings on the current interface to factory default. Supplementary Services After clicking “Service”, you could set “Busy Forwarding”, “No answer forwarding”, “Unconditional forwarding”, “Call waiting”, etc.
Failures Causes Solutions Please download the Error occurs during the program at website The setup file may be damaged. program installation. WWW.ZTEMT.COM reinstall it. Directly run the software Close the software, plug in before the USB Modem is the USB Modem and run it plugged in.
Page 20
Failures Causes Solutions This is normal. If you want to display CD-ROM disk CD-ROM icon will automatically icon, you could firstly disappear once the program is remove the program and installed successfully. then insert the modem again. No CD-ROM disk icon in “My Please restart your Computer”.