1. Manuals
  2. Brands
  3. SMC Networks Manuals
  4. Storage
  5. SMCWUSB32
  6. User manual

SMC Networks SMC EZ Connect 2.4GHz 11 Mbps Wireless USB Flash Drive SMCWUSB32 User Manual

2.4ghz wireless usb flash drive
Hide thumbs Also See for SMC EZ Connect 2.4GHz 11 Mbps Wireless USB Flash Drive SMCWUSB32:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for SMC Networks SMC EZ Connect 2.4GHz 11 Mbps Wireless USB Flash Drive SMCWUSB32

Summary of Contents for SMC Networks SMC EZ Connect 2.4GHz 11 Mbps Wireless USB Flash Drive SMCWUSB32

  • Page 2 Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC.
  • Page 3 Compliances FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications.

  • Page 4: Important Safety Notices

    EC Conformance Declaration – Class B SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II Calle Fructuos Gelabert 6-8, 2o, 4a 08970 – Sant Joan Despi Barcelona, Spain This information technology equipment complies with the essential requirements of the R&TTE Directive 1999/5/EC and all other related provisions of this directive.

  • Page 5: System Requirements

    1 | System Requirements • An available USB port • Windows 98SE/Me/2000/XP • A minimum of 10 MB of free disk space for installing the driver and utility program. • Another IEEE 802.11b or 802.11g compliant device installed in your network, such as the SMC7004VWBR Barricade™...

  • Page 6: Installation Instructions

    3 | Installation Instructions - Device Installation 1) Select an available USB port on the PC 2) Make sure the cap of the SMCWUSB32 is pushed down so that the USB interface is clearly visible 3) Carefully insert the USB adapter’s Type-A plug (i.e., the flat plug) into the USB port 4) Press until it is firmly seated in the port - Using the Laptop Clip and USB Extension Cable 1) Select an available USB port on the PC...
  • Page 7 4 | Flash Drive Installation NOTE: Installation processes may require the use of your original, licensed copy of Windows. Please have your Windows CD available BEFORE proceeding with the installation. The following instructions are for Windows 98SE/Me. Under Windows 2000/XP, your Flash Drive should be automatically installed once you plug the SMCWUSB32 into your USB port.

  • Page 8: Windows Me

    Step 5: Once the system has copied the SMC drivers from the CD, it may then request files from your original Windows disk. Please insert the Windows CD at this time. Step 6: The system will copy the files. Do NOT press [Cancel]. Step 7: Once all the necessary files are copied from the Windows CD, the driver install process will be complete.
  • Page 9 Step 2: Insert the Driver CD and select the [Specify a location:] option. Clear the [Removable Media] checkbox. Then press the [Browse] button and look for the drivers on your CD. This should be located in ?:\Flash Driver. (Note: The ? equals the letter of your CD-ROM drive. In most cases, this is D.) Then click [Next >].
  • Page 10 5 | WLAN Driver/Utility Installation Step 1: Insert the SMCWUSB32 EZ Installation Wizard and Documentation CD. Step 2: Click the [Install Driver/Utility] button. Step 3: Please wait while the utility checks your Operating System Version and prepares to install the SMCWUSB32.
  • Page 11 Step 4: Click the [Next] button to continue. Step 5: Choose the folder where the utility setup files will be installed. It is recommended to leave this value at its default setting. Click [Next] to continue. The program files will now be copied. Please wait.
  • Page 12 Step 6: Please restart your computer to finish the installation of the SMCWUSB32.

  • Page 13: Utility Configuration

    6 | Utility Configuration NOTE: The following applies to Windows 98SE, Me, 2000. Under Windows XP, please use the Wireless Zero Configuration tool built into Windows XP to configure your SMCWUSB32. When the utility program is running, there will be a quick launch icon in the lower right-hand corner of the taskbar.
  • Page 14 Section 1.1 | Status This tab will show you the current profile of the wireless card. Click [Disable Connection] to entirely halt all wirelessly functionality of the SMCWUSB32. Click [Reset] to reboot your SMCWUSB32.
  • Page 15 Section 1.2 | Profile The Profile tab allows to create or delete profiles and configure the wireless network settings. The options for Mode include Infrastructure(Access Point) and Adhoc(Peer-to-Peer). Adhoc networks consist of wireless clients only. In Infrastructure networks, wireless clients connect to wired LANs via Wireless Access Points.
  • Page 16 For more secure data transmissions, it is recommended to enable WEP on your WLAN. Click the [Encryption] button to get to this configuration. The utility supports HEX or ASCII key entries. For the HEX Key Format, the security is enabled by entering 10-digit keys for the 64-bit WEP configuration, and 26-digit keys for a 128-bit WEP configuration.

  • Page 17: Section 1.4 | Statistics

    Section 1.4 | Statistics The Statistics tab is used to monitor TX and RX traffic of the wireless network. It also offers the detailed information on error packets. Each time users switch to this page, the statistics will start counting from zero. Users can press [Reset] button if they want to restart the counter again. If users want to temporarily freeze the current counters, they can press [Pause] button.
  • Page 18 Section 1.5 | About The About screen displays the version information and MAC address. USING WIRELESS ZERO CONFIGURATION 1) After completing the driver installation, in Windows XP, the Wireless Zero Configuration will automatically be enabled. You will see a new wireless network connection in the bottom right-hand corner of your taskbar.
  • Page 19 3) You should see the SSID of your Wireless Base Station or adhoc network in the “Available wireless networks” window. High-light the desired network. 4) If the network is not encrypted, you need to check the [Allow me to connect…] checkbox in order for the [Connect] button to appear.
  • Page 20 5) Select your desired network from the “Available wireless networks” window and then click [Configure]. 6) You will be able to select the “Network Authentication” and “Data encryption” methods. If you have 64 or 128-bit WEP enabled on your network, set the “Data encryption” to WEP, uncheck the “The key is provided for me automatically”...

  • Page 21: Important Notice

    If you have any questions or comments regarding the features or performance of this product, or if you would like information regarding our full line of wireless products, you can visit us at www.smc.com, or you can call us toll-free at 800.SMC.4YOU. SMC Networks stands behind every product sold with a 30-day satisfaction guarantee and a limited-lifetime warranty.

  • Page 22: Troubleshooting

    SMC Technical Support. • Make sure the correct network card driver is installed for your operating system. If necessary, try uninstalling and reinstalling the driver. To do this, first go into the Device Manager, select Network Adapters, and remove the SMC adapter. Then open up your Start Menu, go to Programs, click the "SMCWUSB32 WLAN Utility"...
  • Page 23 • If your wireless station cannot communicate with a computer on the Ethernet LAN when configured for Infrastructure mode, try changing the wireless channel on the AP. Make sure the SSID is the same as that used by the AP for a station with roaming disabled, or the same as that used by the AP's in the extended service set (ESS).
  • Page 24 9 | Frequently Asked Questions • What is a Wireless LAN? A local area network that transmits over the air typically in an unlicensed frequency such as the 2.4GHz band. A wireless LAN does not require lining up devices for line of sight transmission like IrDA. Wireless access points (base stations) are connected to an Ethernet hub or server and transmit a radio frequency over an area of several hundred to a thousand feet which can penetrate walls and other non-metal barriers.
  • Page 25 • What is Authentication Algorithm? Authentication Algorithm is the means by which one station is authorized to communicate with another. In an Open System, any station can request authorization in accordance with the WECA standard. In a Shared key system, only stations that possess a secret encrypted key may participate in the network.
  • Page 26 10 | Technical Specifications Standards: IEEE 802.11b compliant Wireless Data Rates (With Automatic Fall-back): 1/2/5.5/11 Mbps Data Modulation Techniques: DBPSK, DQPSK, CCK Host Interface: USB 1.1 Operating Range: Up to 1,155 ft Network Configuration: Ad-Hoc (Peer-to-Peer) Infrastructure Radio Signal Type: Direct Sequence Spread Spectrum (DSSS) Media Access Protocol: CSMA/CA (Collision Avoidance)

  • Page 27: Temperature Range

    Read Transfer Power Consumption: < 26mA Write Transfer Power Consumption: < 300mA Sleep Mode Power Consumption: < 150mA Flash Memory Size: 32MB Flash Memory Transfer: Read Transfer: 900KB/s Write Transfer: 500KB/s Operating Systems: Windows 98SE/Me/2000/XP Antenna Type: Built-in LED Indicators: Network Link Compliance: USA: FCC Part 15 Class B...
  • Page 28 11 | Terminology 10BaseT - Physical Layer Specification for Twisted-Pair Ethernet using Unshielded Twisted Pair wire at 10Mbps. This is the most popular type of LAN cable used today because it is very cheap and easy to install. It uses RJ-45 connectors and has a cable length span of up to 100 meters. There are two versions, STP (Shielded Twisted Pair) which is more expensive and UTP (Unshielded Twisted Pair), the most popular cable.
  • Page 29 Ethernet - A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move data around at up to 10 million bits per second (Mbps). ESS - ESS (ESS-ID, SSID) stands for "Extended Service Set". More than one BSS is configured to become an Extended Service Set.
  • Page 30 which is implemented in the network adapters that are plugged into the machines. The actual communications path is the cable (twisted pair, coax, optical fiber) that interconnects each network adapter. MAC Address - MAC (Media Access Control) A MAC address is the hardware address of a device connected to a network.
  • Page 31 Subnet Mask - A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers configured like an IP address. It is used to create IP address numbers used only within a particular network (as opposed to valid IP address numbers recognized by the Internet.

This manual is also suitable for:

Wusb32Ez connect smcwusb32

Table of Contents