Advertisement
Available languages
Available languages
6A CHANGE MAIN BAKE BURNER
ORIFICE (Cont.)
F. Remove the 2 burner retention screws.
Burner
G. Lift the front of the burner up slightly and slide
forward setting aside (careful not to damage
the igniter.)
H. Use a 1/2" deepwell socket to remove and
replace the orifice.
I. Reverse these steps to reassemble the
griddle. Push excess capillary back into the
entry hole. Place the unused orifice in the
holder for possible future use.
6B CHANGE COMPANION BAKE
BURNER ORIFICE (if present)
Locate the 3/4" long bake burner orifice.
Select the proper orifice size for your gas and
burner from the conversion chart.
A. Remove the oven door and set aside in a
safe location.
Hold-Down
Screws
Oven
Bottom
B. Remove the 2 oven bottom hold-down
screws from the rear of the cover.
C. Slide the oven bottom forward and set
asside.
Clips
Diffuser Screw
D. Remove the burner diffuser screw.
E. Lift the front of the burner diffuser up
slightly and slide it forward to disengage
the clips at the rear. Set the burner diffuser
aside.
F. Remove the 3 burner retension screws (1 in
front and 2 at the rear)
Burner
Retension
Screws
G. Lift the front of the burner up slightly and
slide leftward to remove.
H. Use a 1/2" deep-
well socket to
remove and re-
place the orifice.
I. Reverse these
steps to reas-
semble the
griddle.Push
excess capillary
back into the entry hole.Place the unused
orifice in the holder for possible future use.
7 CHANGE MAIN/COMPANION
BROIL BURNER ORIFICE
Locate the broil burner orifice.
Select the proper orifice size for your gas and
burner from the conversion chart.
Burner retention
screws
The rear cover should still be removed from
converting the regulator(s). Refer to sec-
tion 2 for details if it is not.
A. Remove the 2 broil duct cover retension
screw. Lift up and slide out to remove.
B. Loosen and remove the broil supply tube
nut from the broil orifice holder.
C. Using an adjustable wrench and a 7/16" (11
mm) box end wrench to loosen and remove
and replace the broil orifice.
D. Reverse these steps to reassemble the
griddle.Push excess capillary back into the
entry hole.Place the unused orifice in the
holder for possible future use.
MODEL
ALL SURF. Main
ZGP48
ZGP36
BURNERS Simmer
RF BURNER
ZGP304
ZGP304 RR, LR, LF
ALL
GRILL
ALL
GRIDDLE
ZGP48/
BAKE MAIN
ZGP36
ZGP30
BAKE MAIN
ZGP48
BAKE COMPANION
ALL
BROIL MAIN
ZGP48
BROIL COMPANION
Remove
screws
BURNER OUTPUT RATINGS: BTU/HR
NG (Natural) Gas, 5" W.C.P.
BTU
ORIFICE
BURNER
RATE
SIZE
0.075"
16,800
(1.90mm)
0.002"
1,200
(0.51mm)
0.075"
Main
16,800
(1.90mm)
0.002"
Simmer
1,200
(0.51mm)
0.050"
8,800
(1.26mm)
Main
Simmer
0.002"
1,200
(0.51mm)
0.0689"
15,000
(1.75mm)
0.076"
18,000
(1.93mm)
0.0886"
24,500
(2.25mm)
0.0866"
23,500
(2.20mm)
0.0531"
10,500
(1.35mm)
0.063"
12,500
(1.60mm)
0.052"
9,000
(1.32mm)
8 ADJUST BURNER FLAMES
Normally, burners do not need further
adjustment. Make adjustments only when
necessary.
A. Turn on the gas. Plug in electrical cord.
B. Turn all burners on highest setting and
check the flames. They should be blue in
color. When using LP gas, the flames may
have some yellow tipping at the ends of the
flame. Foreign particles in the gas line may
cause an orange flame at first, but this will
soon disappear.
C. Turn the burner knob to "LO" while
observing the flame.
Adjust the setting of the upper row of flames
using the valve bypass screw as follows:
Adjustments must be made with two other
burners in operation on a medium setting.
This prevents the upper row of flames from
being set too low, resulting in the flame
being extinguished when other burners are
turned on.
D. To adjust the flame, remove the knobs. Insert
a small flat-blade screwdriver into the hole
in the center of the valve stem to engage
screw.
• If the flames are too small or flutter, turn the
screw counterclockwise.
• If the flames are too large, turn the screw
clockwise.
E. Make the adjustment by slowly turning the
screw until flame appearance is correct.
LP (Propane) Gas, 10" W.C.P.
ID
MODEL
BURNER
190XN
ALL SURF. Main
ZGP48
ZGP36
51SL
BURNERS Simmer
190XN
Main
RF BURNER
ZGP304
51SN
Simmer
126HXN
Main
ZGP304 RR, LR, LF
Simmer
51SN
0.069
ALL
GRILL
0.076
ALL
GRIDDLE
ZGP48/
0.089
BAKE MAIN
ZGP36
0.087
ZGP30
BAKE MAIN
0.053
ZGP48
BAKE COMPANION
160
ALL
BROIL MAIN
132
ZGP48
BROIL COMPANION
BTU
ORIFICE
ID
RATE
SIZE
0.043"
13,800
108XL
(1.08mm)
0.013"
1,200
34SL
(0.34mm)
0.043"
13,800
108XL
(1.08mm)
0.013"
1,200
34SL
(0.34mm)
0.033"
7,900
84XL
(0.84mm)
0.013"
1,200
34SL
(0.34mm)
0.047"
14,000
0.047
(1.19mm)
0.047"
16,000
0.047
(1.19mm)
0.055"
23,000
0.055
(1.397m)
0.0531"
21,500
0.053
(1.35mm)
0.0374"
10,000
0.037
(0.95mm)
0.041"
11,500
104
(1.04mm)
0.0360"
9,000
91
(0.91mm)
2
Advertisement
