Yamaha DTX402 Series Owner's Manual

ELECTRONIC DRUM KIT
DTX482K
Thank you for purchasing the Yamaha DTX482K! As a high-end model of the DTX402 series, the DTX482K comes standard
with three cymbal pads (two crashes and one ride) and the DTX-series XP80 Snare Pad. We recommend that you read this
manual carefully so that you can fully take advantage of the advanced and convenient functions of the instrument. We also
recommend that you keep this manual in a safe and handy place for future reference.
Before using this product, be sure to read the "PRECAUTIONS" on pages 4 to 5 on the DTX402K, DTX432K, and DTX452K Owner's Manual.
NOTICE
Some objects made of rubber and similar materials can easily stain the drumhead of the snare pad. Do not leave such objects in contact with the drumhead for a long period of
time. Pay special attention to avoid stacking the pads when putting them in storage, for example.
1.
Package Content
After opening up the package containing your electronic drum kit, please verify that all of the following parts are present.
DTX482K Package Content
Rack (Large) Rack (Small)
Pipe for
TOM3
Cymbal/hi-hat pads (×2) Crash cymbal pad
Nine-channel snake cable Drum key
Additional Cymbal pad
Cymbal holder (×1)
Cymbal pad (×1)
Published 08/2014 POMA*.*-**A0
EN
Owner's Manual
Rod for the snare pad Hi-hat holder Cymbal holders (×2)
Stopper
Drum module
HH65 Hi-hat controller
Sensor (bumps)
Cable bands (×3) AC adaptor
* May not be included depending on your particular area.
Please check you're your Yamaha dealer.
DTX482K Owner's Manual (this booklet)
DTX402K, DTX432K, and DTX452K Owner's Manual
KP65 Owner's Manual
XP70, XP80 Owner's Manual
XP80 Snare Pad
Stopper (×1)
XP80 main unit (×1)
Stereo audio cable (×1)
2.
Assembly Guide (1/2)
Manual Development Group
© 2018 Yamaha Corporation
To assemble the DTX482K, refer to this Owner's Manual and the DTX402K, DTX432K, and DTX452K Owner's Manual
VAU5550
Fully Assembled DTX482K
Step 8
Step 7
Step 6
Step 4
Step 2 Step 3
No Stopper
Step 12
 Attaching the cymbal holder for the additional cym-
KP65
bal pad.
Kick pad
1. 
Loosen the ( 1,
w
r
FP6110A
2
Foot pedal
q
1
2.
Loosen the clamp bolt of the cymbal holder.
Clamp bolt (×1)
Clamp bolt
1
Step 10
Step 9
Step 5
Step 11 Step 12
3.

2) key bolts and detach the pipe for TOM3.
Pipe for TOM3
e
4.
5.
Step 1
Step 2
Cymbal holder
Step 3
Step 9
Additional cymbal pad
Cable band position
CAUTION
• Choose a flat, hard surface on which to
assemble your electronic drum kit.
• Take care to avoid mixing up parts or assem-
bling them in the wrong direction. In addition,
Step 1
the assembly steps should be completed one
at a time in the order described.
• The assistance of at least one other person
will be required when assembling the elec-
tronic drum kit.
• Once a piece has been assembled, be sure to
tighten the corresponding key bolts.
• To disassemble your electronic drum kit, carry
out the assembly sequence in reverse.
Slide the holder clamp onto the TOM3 pipe, and lightly tighten the
clamp bolt of the cymbal holder.
Holder clamp
Clamp bolt
Attach the TOM3 pipe back to the large rack.
Pipe for TOM3

Tighten the key bolt ( in the above figure) on the large rack and the
clamp bolt of the cymbal holder.
Turn the entire large rack over and continue with the
assembly by following the instructions on pages 13 and 14
of the DTX402K, DTX432K, and DTX452K Owner's
Manual
Continue to the other side.