Enhancing Your System; Troubleshooting Chart - Sharp CD DHS1050P Operation Manual

Timer and sleep operation (Remote
control only) (continued)
To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
1
Set the sleep time (see above, steps 1 - 5).
2
While the sleep timer is set, set the timer playback
(steps 2 - 10, page 12).
Sleep timer Timer playback
setting setting
1 - 90 minutes
Sleep operation will
automatically stop

Enhancing your system

The connection cord is not included. Purchase a
commercially available cord as shown below.
Portable audio
player, etc.
To the
line
output
jack
PHONES
AUDIO IN
USB
Audio cable (not supplied)
Listening to the playback sounds of
portable audio player, etc.
1
Connect a portable audio player etc. to the front AUDIO
IN jack.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the AUDIO IN/USB button repeatedly to select
AUDIO IN.
4
Play the connected equipment.
If volume level of the connected device is too high,
sound distortion may occur. Should this happen, lower
the volume of the connected device.
If volume level is too low, increase the volume of the
connected device.
Note:
To prevent noise interference, place the unit away from the
television.
Headphones
Before plugging in or unplugging the headphones,
reduce the volume.
Be sure your headphones have a 1/8" (3.5 mm) diameter
plug and impedance between 16 and 50 ohms. The
recommended impedance is 32 ohms.
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME
control.
Desired time
Timer playback
start time
5
4
3
2
1
MINI COMPONENT SYSTEM
CD-DHS1050P
TIMER REMOTE
SENSOR
POWER
ON/ STAND-BY
OPEN / CLOSE
VOL. VOL.
iPod/iPhone
5
CD
4
TUNER
(BAND) 3
TAPE
TUNING
PRESET
2
AUDIO IN
USB
1

Troubleshooting chart

Many potential problems can be resolved by the owner
without calling a service technician. If something is wrong
with this product, check the following before calling your
authorized SHARP dealer or service center.
General
Symptom
The clock is not set
to the correct time.
When a button is
End time
pressed, the unit
does not respond.
No sound is heard.
CD player
Symptom
Playback does not
start.
PHONES
Playback stops in
the middle or is not
performed properly.
Playback sounds
AUDIO IN
are skipped, or
stopped in the
middle of a track.
"ER-CD21"
appears on the
display.
Cassette deck
Symptom
Sound skipping.
Cannot hear treble.
Sound fl uctuation.
Cannot remove the
tape.
E-13
Possible cause
Did a power failure occur?
Reset the clock. (Refer page
11)
Set the unit to the power
stand-by mode and then turn
it back on.
If the unit still malfunctions,
reset it. (Refer page 14)
Is the volume level set to "0"?
Are the headphones
connected?
Are the speaker wires
disconnected?
Possible cause
Is the disc loaded upside
down?
Does the disc satisfy the
standards?
Is the disc distorted or
scratched?
Is the unit located near
excessive vibrations?
Is the disc very dirty?
Has condensation formed
inside the unit?
Is the disc tray stopped with
force? Set the unit to the
power stand-by mode and
then turn it back on.
Possible cause
Is there any slack?
Is the tape stretched?
Are the capstans, pinch
rollers, or heads dirty?
If a power failure occurs
during playback, the heads
remain engaged with the
tape. Do not open the
compartment with great
force.