Table of Contents
Advertisement
Quick Links
Installation instructions
• Read these instructions carefully before installing or using this product.
• Please make this information available to the person responsible for installing the product as it
• In order to avoid a hazard, this appliance must be installed according to these instructions for
This cooktop has been designed and constructed in accordance with the following codes and specifications:
AS/NZS 60335-1
General Requirements for Domestic electrical appliances
AS/NZS 60335-2-6
Particular Requirements for Domestic electrical cooking appliances
AS/NZS 1044
Electromagnetic Compatibility Requirements.
Product dimensions and clearances
The installation shall comply with the dimensions in Figs. 1 and 2, bearing in mind the following requirements:
• A minimum clearance of 40 mm for CE302 models and 30 mm for CE604 models has to be kept between the
bottom of the cooktop and the top of an underbench appliance or a thermal protection barrier (see Figs. 5-7).
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_inst
could reduce your installation costs.
installation.
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
1
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel AS/NZS 60335-1
Summary of Contents for Fisher & Paykel AS/NZS 60335-1
-
Page 1: Installation Instructions
• In order to avoid a hazard, this appliance must be installed according to these instructions for installation. This cooktop has been designed and constructed in accordance with the following codes and specifications: AS/NZS 60335-1 General Requirements for Domestic electrical appliances AS/NZS 60335-2-6... - Page 2 • Overhead clearances - In no case shall the clearance between the highest part of the cooktop and a range hood be less than 600 mm. Any other downward-facing combustible surface less than 600 mm above the highest part of the cooktop shall be protected for the full width and depth of the cooking surface area in accordance with local regulations in force.
- Page 3 Fig. 2 CE604 models clearances Fig. 1 CE302 models clearances Fig. 4 CE604 models product and cutout dimensions Fig. 3 CE302 models product and cutout dimensions https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_inst Updated: Sat, 09 Mar 2019 07:23:30 GMT Powered by...
-
Page 4: Installing A Thermal Protection Barrier
Installing a thermal protection barrier If the cooktop is installed over drawers or cupboards and its underside surface thus becomes accessible after installation, a thermal protection barrier must be fitted at least 40 mm (for CE302 models) or 30 mm (for CE604 models) beneath the base of the cooktop (see Figs. - Page 5 2. Stretch gasket “D” (Figs. 10 and 11) over the edge of the cutout, being careful to overlay the junction edges. 3. Turn the cooktop upside down, place it on a soft surface and fasten the brackets F and R to the appropriate socket holes, without tightening the screws B for the moment.
-
Page 6: Electrical Requirements
Fig. 11 CE302 models front and rear side CE604 models front side Electrical requirements • The appliance must be connected to the mains electricity supply checking that the voltage corresponds to the value given in the rating plate and that the power supply cable sections can withstand the load specified on the plate. -
Page 7: Connecting The Power Supply Cable - Ce604 Models
Fig. 13 Connection diagram Fig. 12 Unhooking the terminal block cover Fig. 14 Fixing the p Connecting the power supply cable - CE604 models 1. Turn the cooktop over and place it on a soft surface. 2. Unhook the terminal board cover by inserting a screwdriver into the two hooks C (fig. 15). 3. -
Page 8: Wiring Diagram - Ce302 Models
Fig. 16 Connection diagram Fig. 15 Connecting the power supply cable Fig. 17 Bridging links Wiring diagram - CE302 models Fig. 18 CE302 wiring diagram https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_inst Updated: Sat, 09 Mar 2019 07:23:30 GMT Powered by... -
Page 9: Wiring Diagram - Ce604 Models
F1/2 Hotplate switches Line pilot lamp Rapid hotplate 2000 W - 230 V Regular hotplate 1000 W - 230 V Terminal block Earth connection Wiring diagram - CE604 models Fig. 19 CE604 wiring diagram F1/2/3/4 Hotplate switches Line pilot lamp Rapid hotplate 2000 W - 230 V Rapid hotplate 1500 W - 230 V Regular hotplate 1500 W - 230 V... -
Page 10: Installation Checklist
Terminal block Earth connection Installation checklist Please check through the list provided to ensure correct installation. • Is the product earthed? • Check that the power supply cable is NOT touching the product. This will ensure that the cable is not damaged by heat from the product. •...