Related Manuals for ATEN CS1944DP
Summary of Contents for ATEN CS1944DP
- Page 1 CS1942DP / CS1944DP 2/4-Port USB 3.0 4K DisplayPort Dual Display KVMP Switch RS-232 Commands V1.0 User Manual www.aten.com...
-
Page 2: Emc Information
CS1942DP / CS1944DP RS-232 Commands EMC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. - Page 3 CS1942DP / CS1944DP installation are managed via HyperTerminal sessions on systems that are running Windows. In order to use this feature to send commands to the CS1942DP / CS1944DP, you must first download and install a HyperTerminal application. For detailed instructions and information about each of the commands provided in this manual, please refer to the CS1942DP / CS1944DP user manual.
- Page 4 CS1942DP / CS1944DP RS-232 Commands Console Login - HyperTerminal Once a physical connection from the computer to the CS1942DP / CS1944DP has been made, you can establish a HyperTerminal session using the instructions below. 1. Open the HyperTerminal application, and configure the port settings for COM1 port, then click OK.
- Page 5 RS-232 commands to control the switch from the computer. When RS-232 control is enabled via the Open + [Enter] command, the CS1942DP / CS1944DP’s front panel pushbuttons and hotkeys (excluding the mouse cursor shift and monitor layout hotkeys) will be disabled, until the serial connection is closed.
- Page 6 The Open and Close commands allows you to start and end the link between the computer sending RS-232 commands and the CS1942DP / CS1944DP. When the link is open, the CS1942DP / CS1944DP only accepts RS-232 commands and will not respond to front panel pushbuttons and hotkeys (excluding the mouse cursor shift and monitor layout hotkeys) –...
-
Page 7: Switch Port Commands
CS1942DP / CS1944DP RS-232 Com- Switch Port The Switch Port command allows you to switch ports. The default port is 01. Use the Formula - to set Parameters - to create a Command. Formula: Command + Control + [Enter] Parameters:... -
Page 8: Set Baud Rate
CS1942DP / CS1944DP RS-232 Commands Set Baud Rate The Set Baud Rate command allows you to configure the baud rate setting for the serial port connection. The default baud rate is 19200. Use the Formula - to set Parameters - to create a Command. -
Page 9: Keyboard Language Layout
CS1942DP / CS1944DP RS-232 Com- Keyboard Language Layout The Keyboard Language Layout command allows you to change the keyboard language layout. The default language is English. Use the Formula - to set Parameters - to create a Command. Formula: Command + Control + [Enter]... -
Page 10: Hotkey Setting
CS1942DP / CS1944DP RS-232 Commands Hotkey Setting The Hotkey Setting command allows you to change the hotkey used to invoke the HSM (Hotkey Setting Mode). The default hotkey is [Num Lock] + [-]. Use the Formula - to set Parameters - to create a Command. -
Page 11: Hotkey Switching
CS1942DP / CS1944DP RS-232 Com- Hotkey Switching The Hotkey Switching command allows you to change the hotkey used for switching. The default hotkey is [Scroll][Scroll]. Use the Formula - to set Parameters - to create a Command. Formulas: Command + Control + [Enter]... -
Page 12: Usb Reset
CS1942DP / CS1944DP RS-232 Commands USB Reset The USB Reset command allows you to reset the USB connection. The default USB reset setting is off. Use the Formula - to set Parameters - to create a Command. Formulas: Command + Control + [Enter]... -
Page 13: Restore Default Settings
Restore Default Value Command The available formula for the Restore Default Settings command is as follows: 1. Command + Control + [Enter] For example, to restore all CS1942DP / CS1944DP settings back to the default, type the following: reset on [Enter]... -
Page 14: Firmware Upgrade
CS1942DP / CS1944DP RS-232 Commands Firmware Upgrade The Firmware Upgrade command allows you to enable the firmware upgrade mode. The default setting is off. Use the Formula - to set Parameters - to create a Command. Formulas: Command + Control+ [Enter]... -
Page 15: Kvm Status
KVM Status Command The available formula for the KVM Status command is as follows: 1. Command + Control + [Enter] For example, to display the CS1942DP / CS1944DP’s configuration status, type the following: status on [Enter] A message similar to the one below will then appear:... - Page 16 CS1942DP / CS1944DP RS-232 Commands...