Specifications - Milwaukee FUEL M18 FPD2 Operator's Manual

When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
Do not use a battery pack or tool that is dam-
explosion or risk of injury.
Do
excessive temperature.
perature above 130°C (265°F) may cause explosion.
Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range may damage the battery and increase the risk
SERVICE
Have
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorised service providers.
SPECIFIC SAFETY RULES FOR
DRILL / DRIVERS
Safety instructions for all operations
Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
the auxiliary handle(s). Loss of control can
cause personal injury.
old the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory or fasteners may contact
hidden wiring. Cutting accessory or fasteners
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
Safety instructions when using long drill bits
operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the
bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
Always start drilling at low speed and with the
bit tip in contact with the workpiece. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage or loss of control, resulting
in personal injury.
To reduce the risk of injury, wear
WARNING
a dust mask. In applications that
produce a considerable amount of dust, use an
OSHA compliant dust extraction solution in
accordance with the solution's operating instruc-
tions.
Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE
replacement.
WARNING
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
lead from lead-based paint
crystalline silica from bricks and cement and other
masonry products, and
arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
-
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
ADDITIONAL BATTERY SAFETY RULES
Charging
WARNING
a short circuit, never immerse your tool, battery pack or
charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater,
certain
bleach-containing products, etc., can cause a short
circuit.
Volts.............................................................18V DC
Battery Type .................................................M18™
Charger Type................................................M18™
Recommended Ambient
Operating Temperature ....................-18°C to 52°C
Cat. No. .................................................M18 FDD2
No Load RPM ............ Low 0 - 550
Steel ..............................................................13mm
Wood Flat Bit .............................................. 38mm
Auger Bit ........................................... 38mm
Hole Saw .......................................... 89mm
Screws (dia.)................................ 15.88mm
Self Feed Bits ................................... 65mm
Cat. No. ..................................................M18 FPD2
No Load RPM ............ Low 0 - 550
BPM ................................................High 0 - 32,000
Steel ..............................................................13mm
Wood Flat Bit .............................................. 38mm
Auger Bit ........................................... 38mm
Hole Saw .......................................... 89mm
Screws (dia.)................................15.88mm
Self Feed Bits ................................... 65mm
Masonry .....................................................15.88mm
3
®
service facility for
Some dust created by power sanding,
sawing, grinding, drilling, and other
To reduce the risk of fire, personal
injury, and product damage due to
industrial chemicals,
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
Blows per Minute Under Load (BPM)

SPECIFICATIONS

a
and bleach or
(0°F to 125°F)
High 0 -2000
High 0 -2000