Hussmann RDI-27 Installation & Operation Manual page 49

Menu survey
Parameters
Function
Normal operation
Temperature (set point)
Thermostat
Di erential
Max. limitation of setpoint setting
Min. limitation of setpoint setting
Adjustment of temperature indication
Temperature unit (°C/°F)
Correction of the signal from S4
Correction of the signal from S3
Manual service, stop regulation, start regulation (-1, 0, 1)
Displacement of reference during night operation
De nition and weighting, if applicable, of thermostat sensors
- S4% (100%=S4, 0%=S3)
The heating function is started a number of degrees below the
thermostats cutout temperature
Activation of reference displacement r40
Value of reference displacement (activate via r39 or DI)
Alarm
Delay for temperature alarm
Delay for door alarm
Delay for temperature alarm after defrost
High alarm limit
Low alarm limit
Alarm delay DI1
Alarm delay DI2
Signal for alarm thermostat. S4% (100%=S4, 0%=S3)
Compressor
Min. ON-time
Min. OFF-time
Time delay for cutin of comp.2
Compressor relay 1 must cutin and out inversely
(NC-function)
Defrost
Defrost method (none/EL/GAS/BRINE)
Defrost stop temperature
Interval between defrost starts
Max. defrost duration
Displacement of time on cutin of defrost at start-up
Drip o time
Delay for fan start after defrost
Fan start temperature
Fan cutin during defrost
0: Stopped
1: Running
2: Running during pump down and defrost
Defrost sensor (0=time, 1=S5, 2=S4)
Pump down delay
Drain delay
Max. aggregate refrigeration time between two defrosts
Defrost on demand - S5 temperature's permitted variation dur-
ing frost build-up. On central plant choose 20 K (=o )
Delay of hot gas defrost
Fan
Fan stop at cutout compressor
Delay of fan stop
Fan stop temperature (S5)
HACCP
Actual temperature measurement for the HACCP function
Last registered peak temperature
Selection of function and sensor for the HACCP function. 0 = no
HACCP function. 1 = S4 used (maybe also S3). 2 = S5 used
Alarm limit for the HACCP function
Time delay for the HACCP alarm
Select signal for the HACCP function. S4% (100% = S4, 0% = S3)
Real time clock
Six start times for defrost.
Setting of hours.
0=OFF
Six start times for defrost.
Setting of minutes.
0=OFF
Clock - Setting of hours
Clock - Setting of minute
Clock - Setting of date
Clock - Setting of month
Clock - Setting of year
Miscellaneous
Delay of output signals after start-up
20
Codes 1
---
*** r01
*** r02
*** r03
r04
r05
r09
r10
r12
r13
r15
r36
r39
r40
A03
*** A04
A12
*** A13
*** A14
A27
A28
A36
c01
c02
c05
c30
d01
d02
d03
d04
d05
d06
d07
d08
d09
d10
d16
d17
d18
d19
d23
F01
F02
F04
h01
h10
h11
h12
h13
h14
t01-t06
t11-t16
*** t07
*** t08
*** t45
*** t46
*** t47
o01
Manual RS8EP502 © Danfoss
EL-diagram number (page 6)
2 3 4 5 6 7 8 9
12-2015
49
SW = 2.3x
Min.- Max.- Factory Actual
10 value value setting setting
-50.0°C 50.0°C 2.0°C
0.1 K 20.0K 2.0 K
-49.0°C 50°C 50.0°C
-50.0°C 49.0°C -50.0°C
-20.0 K 20.0 K 0.0 K
°C °F °C
-10.0 K +10.0 K 0.0 K
-10.0 K +10.0 K 0.0 K
-1 1 0
-10.0 K 10.0 K 0.0 K
0% 100% 100%
-15.0 K -3.0 K -15.0 K
OFF ON OFF
-50.0 K 50.0 K 0.0 K
0 min 240 min 30 min
0 min 240 min 60 min
0 min 240 min 90 min
-50.0°C 50.0°C 8.0°C
-50.0°C 50.0°C -30.0°C
0 min 240 min 30 min
0 min 240 min 30 min
0% 100% 100%
0 min 30 min 0 min
0 min 30 min 0 min
0 sec 999 sec 0 sec
0 1 0
OFF ON OFF
no bri EL
0.0°C 25.0°C 6.0°C
0 hours 240 8 hours
hours
0 min 180 min 45 min
0 min 240 min 0 min
0 min 60 min 0 min
0 min 60 min 0 min
-15.0°C 0.0°C -5.0°C
0 2 1
0 2 0
0 min 60 min 0 min
0 min 60 min 0 min
0 hours 48 hours 0 hours
0.0 K 20.0 k 20.0 K
0 min 60 min 0 min
no yes no
0 min 30 min 0 min
-50.0°C 50.0°C 50.0°C
0 2 0
-50.0°C 50.0°C 8.0°C
0 min. 240 min. 30 min.
0% 100% 100%
0 hours 23 hours 0 hours
0 min 59 min 0 min
0 hours 23 hours 0 hours
0 min 59 min 0 min
1 31 1
1 12 1
0 99 0
0 s 600 s 5 s
AK-CC 210