Technical Data; Battery Charging; Auxiliary Handle - Bosch GBH 36 V-EC Compact Original Operating Instructions

OBJ_BUCH-589-005.book Page 8 Wednesday, September 14, 2016 11:21 AM
8 | English

Technical Data

Rotary Hammer
Article number
Speed control
Right/left rotation
Rated voltage
Rated power input
Output power
Impact rate
Impact energy per
stroke according to
EPTA-Procedure 05/2009
Speed
Tool holder
Spindle collar diameter
Drilling diameter, max.:
– Concrete
– Steel
– Wood
max. Diameter screw
Weight according to EPTA-
Procedure 01:2014
* dependent of the battery pack being used
Battery
Permitted ambient
temperature
– when charging
– during operation*
– during storage
Recommended batteries
* Limited performance at temperatures <0
Assembly

Battery Charging

 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
1 609 92A 1VN | (14.9.16)
Removing the battery
The battery 12 is equipped with two locking levels that should
GBH 36 V-EC Compact
prevent the battery from falling out when pushing the battery
3 611 J03 R..
unlocking button 13 unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a
spring.

V= 36
W 430
W 320
-1
min 0 –4850
J 1.8
-1
min 0 –1500
SDS-plus To remove the battery 12:
– Push the battery against the base of the power tool (1.)
mm 48
and at the same time press the battery unlocking button 13
(2.).
mm 18
– Pull the battery out of the power tool until a red stripe be-
mm 13
comes visible (3.).
mm 30
– Press the battery unlocking button 13 again and pull out
mm 6
the battery completely.
Battery Charge-control Indication
kg 2.7 - 3.3*
The three green LEDs of the battery charge-control indicator
15 indicate the charge condition of the battery 12. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
– Push button 16 to indicate the charge condition (also pos-
°C 0...+45
sible when the battery is removed). The battery charge-
°C –20...+50
control indicator automatically goes out after approx.
°C –20...+60
5 seconds.
GBA 36V x,xAh H-.
LED
°C
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 16, then the bat-
tery is defective and must be replaced.
During the charging procedure, the three green LEDs light up
one after the other and briefly go out. The battery is fully
charged when the three green LEDs light up continuously. The
three LEDs go out again approx. 5 minutes after the battery
has been fully charged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.

Auxiliary Handle

 Operate your machine only with the auxiliary handle
17.
Capacity
≥2/3
≥1/3
<1/3
Reserve
Bosch Power Tools