Table of Contents
Advertisement
II. RECEIPT INSPECTION
II. a - RECEIPT INSPECTION:
All Traulsen products are factory tested for performance and are free
from defects when shipped. The utmost care has been taken in crating
this product to protect against damage in transit.
You should carefully inspect your unit for damage during delivery. If
damage is detected, you should save all the crating materials and
make note on the carrier's Bill Of Lading describing the damage. A
freight claim should be filed immediately. If damage is subsequently
noted during or immediately after installation, contact our customer
care team to file a freight claim. There is a fifteen (15) day limit to file
freight damage with the carrier. Under no condition may a damaged
unit be returned to Traulsen without first obtaining written permission
(return authorization). You may contact Hobart/Traulsen customer care
at 800-333-7447 to request a return or file a claim.
III. OPERATIONAL GUIDELINES
III. a - OPERATIONAL GUIDELINES:
Follow these simple guidelines for proper TS Series Operation.
1. Keep the condenser clean. Don't obstruct airflow.
2. Use up to 6" deep stainless steel or aluminum pans.
3. All pan spaces should be filled any time the unit is running, even if
some pans are empty.
4. Keep the room temperature at 86
5. Do not allow air drafts (such as heat, A/C or ventilation) to blow on
or over the rail area. This will disrupt the air blanket over the product
area, resulting in poor holding temperatures.
6. Rail covers should be closed over the rail as much as possible.
7. Product should be loaded into the rail at a maximum temperature of
36
0
F. The TS Series unit was not designed to chill warm product, but
to hold refrigerated product at a safe temperature.
8. Keep area around the evaporator fans clear.
IV. INSTALLATION
IV. a - LOCATION:
Select a proper location for your unit, away from extreme heat or cold.
Allow enough clearance between the unit and the side wall in order to
make use of the door stay open feature at 120
operates up to 90
). The door(s) must be able to open a minimum of
0
90
in order to make use of the maximum clear door width.
0
IV. b - PACKAGING:
Your Traulsen unit is shipped from the factory bolted to a sturdy wooden
pallet in stretch wrapped material and wood crate.
Most exterior stainless steel surfaces have a protective vinyl covering to
prevent scratching during manufacturing, shipping and installation.
After the unit is installed in place of application peel, remove and discard
the covering from all surfaces.
F (30
C) or less.
0
0
0
(self-closing feature
IV. INSTALLATION (CONTINUED)
IV. b - PACKAGING (continued):
To remove the wooden pallet, first if at all possible, we suggest that the cabinet
remain bolted to the pallet during all transportation to the point of final installation.
The bolts can then be removed with a 1/2" socket wrench. Avoid laying the unit
on its front, side or back for removal of the pallet.
NOTE: Traulsen does not recommend laying the unit on its front, side or
back. If you must, please allow the unit to remain in an upright position
for 24 hours before plugging it in so that the compressor oils and refriger-
ant may settle.
IV. c - INSTALLING/ADJUSTING LEGS OR CASTERS:
To install legs or casters, slide leg or caster into the caster channel from the side
of the unit without the refrigeration system.
To adjust the legs or casters, loosen the two bolts and move leg or caster to desired
location, spacing between leg or caster not to exceed 48 inches. Leg or caster on
each end of the unit can not exceed 8 inches from the end of the cabinet.
NOTE: Traulsen recommends to position legs or casters under the mullion
when possible.
IV. d - DOORS
:
Your Traulsen TS Series model door(s) are field re-hingeable. If re-hinging is
required, please contact our in-house service department at 800-825-8220 for
re-hinging instructions.
IV. e - INSTALLING OPTIONAL DRAWERS
Doors are supplied standard on all TS Series models. However, we have engineered
our refrigerator models with a drop-in feature that allows you to easily convert
door(s) into two 6" deep drawers or three 4" deep drawers.
The door(s) on the refrigerator models can easily be converted to drawers in the
field. To begin the process, open the door to its maximum position. Support the
non-hinged end of the door so minimum movement occurs. When the bolts from
the lower hinge plate are removed, remove the lower hinge plate and then the door
from the top hinge bracket plate and then the door from the top hinge bracket.
The hinge plate pin and plastic bushing will remain in the top hinge plate.
NOTE: The lower hinge plate is under spring tension.
-2-
:
Hide quick links:
Advertisement
Table of Contents
