Advertisement
Quick Links
Assembly Instructions
SC5 ASSEMBLY INSTRUCTIONS
STEP 1: Install the front stabilizer using two (2) pieces each of the
M10 x 25mm hex head screws, M10 split lock washers, and M10
washers. Repeat this step to attach the rear stabilizer.
STEP 3: Pull down on the seat slider locking pin then slide the
seat assembly onto the seat post installed in Step 2, tightening
the fore/aft adjustment knob to lock the seat slider into place.
NOTE: The fore/aft adjustment knob may need to be loosened.
SC5 + SC7 + SC Power Install Sheet
Applies to: SC5 (9-7410) + SC7 (9-7400) + SC Power (9-7380)
STEP 2: Install the seat post by loosening the height adjustment
pop pin, then pulling outwards on the pin while sliding the seat
post into the frame.
Fore/Aft
Adjustment
Knob
M8 Washer
Threaded Collar
Locking Nut
Trapezoidal
Locking Nut
STEP 4: Insert one (1) piece of the trapezoidal locking nut into
the handlebar post then slide the handlebar onto the handlebar
post. Next, insert one (1) piece of the threaded collar locking nut
through the handlebar and into the trapezoidal locking nut, tight-
ening with a 10mm allen key. Slide one (1) M8 washer onto the
fore/aft adjustment knob then tighten the knob into the threaded
collar locking nut. Finally, secure the end cap onto the handlebar
post using one (1) piece of the M4 x 10mm screw.
Page 1
620-8607 Rev. A
Advertisement
Related Manuals for Schwinn SC7
Summary of Contents for Schwinn SC7
-
Page 1: Assembly Instructions
Assembly Instructions SC5 + SC7 + SC Power Install Sheet Applies to: SC5 (9-7410) + SC7 (9-7400) + SC Power (9-7380) SC5 ASSEMBLY INSTRUCTIONS STEP 1: Install the front stabilizer using two (2) pieces each of the STEP 2: Install the seat post by loosening the height adjustment... - Page 2 Assembly Instructions SC5 ASSEMBLY INSTRUCTIONS CONT. STEP 5: Install the user right side pedal into the crank arm then use a torque wrench and a 8mm allen socket to secure one (1) piece of the crank bolt from the other side of the pedal, torquing to 33-37 ft-lbs (45-50 Nm).
- Page 3 Assembly Instructions SC7 ASSEMBLY INSTRUCTIONS Fore/Aft Adjustment Knob Threaded M8 Washer Stabilizer Plate Threaded Collar Locking Nut Trapezoidal Locking Nut STEP 1: Slide the threaded stabilizer plate into the bike frame STEP 2: Insert one (1) piece of the trapezoidal fore/aft locking...
- Page 4 Assembly Instructions SC7 ASSEMBLY INSTRUCTIONS CONT. STEP 6: Install the pedal into the crank arm then use a torque wrench and a 8mm allen socket to secure one (1) piece of the crank bolt from the other side of the pedal, torquing to 33-37 ft- lbs (45-50 Nm).
- Page 5 Assembly Instructions SC POWER ASSEMBLY INSTRUCTIONS Fore/Aft Adjustment Knob Threaded M8 Washer Stabilizer Plate Threaded Collar Locking Nut Trapezoidal Locking Nut STEP 1: Slide the threaded stabilizer plate into the bike frame STEP 2: Insert one (1) piece of the trapezoidal fore/aft locking then use a 13mm socket to secure the rear stabilizer onto the nut into the handlebar post then slide the handlebars onto frame using two (2) pieces of the M8 x 30mm bolts and M8 wash-...
- Page 6 Assembly Instructions SC POWER ASSEMBLY INSTRUCTIONS CONT. STEP 6: Install the pedal into the crank arm then use a torque wrench and a 8mm allen socket to secure one (1) piece of the crank bolt from the other side of the pedal, torquing to 33-37 ft- lbs (45-50 Nm).