Universal Remote Control CLIKR-5 Operating Instructions

1 4
Introduction Button Functions
Operating Instructions For
CLIKR TM -5
CLIKR ™ -5 The UR5U-8700L & UR5U-8720L
are designed to operate the Scientific-
Atlanta, Pioneer, Pace Micro, Samsung and
Motorola digital set tops, plus the majority
Cable Remote Control
of TV, VCR, DVD and AUDIO equipment on
the market as shown below.
CABLE : Cable Converters TV : Televisions
UR5U-8700L & UR5U-8720L
VCR : VCRs and TV/VCRs DVD: DVD Players
AUX : Audio Receivers and DVRs, etc.
2
Replacing Batteries
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
3
Operations
5
Programming the Remote Control
DEFAULT STATE:
There are two ways you can program your CLIKR
Component Default: CABLE Set Top Box (STB)
* The Pre-Programmed 3-Digit Code Method
Channel Default: CABLE channel and numbers
* The Auto-Search Method
through the CABLE STB. You have the option of
controlling your CABLE channel and numbers The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
through the TV or VCR. Refer to section F for code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest
programming steps. and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Auto-Search Method scans through all the codes in the remote control, one at a time.
Volume Default: Volume and Mute control are
automatically transferred to the respective IMPORTANT SETUP NOTE!
Component mode you select, as follows: CBL:
This pertains to all programming steps. When you are in setup mode, a component LED will
Cable Set Top Box / TV: TV / AUX: AUX. Volume
light for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off
and Mute control for VCR and DVD are
and exit setup mode and you will need to start over.
Universal Remote Control, Inc. automatically transferred to the TV. However,
A. Pre-Programmed 3-Digit Code Method
you have the option of controlling CABLE
www.universalremote.com
Volume and Mute through the TV, VCR or AUX.
OCE-0060C REV 12 (08/17/11)
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX).
Refer to section G for programming steps.
Downloaded from www.Manualslib.com
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light
will turn on for 30 seconds indicating
the unit is ready to be programmed.
STEP3 Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
*Note : If the 3-digit code number you just
entered is correct, the Component will
turn Off. If it did not turn Off, continue
entering code numbers listed for that
brand until the Component turns Off.
STEP4 After you've entered the correct code
number and the Component has turned
Off, press the [POWER] button to turn
the Component back On. Now it is time
to test the VOLUME and MUTE buttons
for the TV (or PLAY and STOP buttons
for VCR and DVD) to make sure they all
work. If any of the functions do not
work as they should, repeat from STEP
3 using the next 3-digit code number
listed for that brand until you find the
best Component code.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the same
[COMPONENT] button one more time.
The Component LED light will blink
twice to confirm that the code was
successfully stored.
Now, program the rest of your Components by
repeating STEPS 1-5.
*Note : If the Pre-Programmed Method did not
work, or if the Code Tables do not list
your Component brand, use the Auto-
Search Method as explained in Section B.
B. Auto-Search Method
STEP1 Turn on the Component you want to
TM -5 remote:
program (TV, VCR, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light
will turn on for 30 seconds indicating
the unit is ready to be programmed.
STEP3 Point the remote toward the Component
and press the [CH ] or [CH ] button
one step at a time or keep it pressed.
The remote will emit a series of ON/OFF
commands. Release the [CH ] or
[CH ] button as soon as the Component
turns Off.
manuals search engine
STEP4 Test functions. (Same as for 3-Digit *Note : If the 3-digit code number you just STEP1 Press the [TV] button and the
Code Programming Method - Section entered is the correct number, the
[OK/SEL] button simultaneously for 3
Component will turn Off. If it did
A). If any of the functions do not work as
seconds. The [TV] Component LED
not turn Off, continue entering
they should, repeat from STEP 3 using
will turn on for 30 seconds.
code numbers listed for that brand
[CH ] or [CH ] buttons to find the
until the Component turns Off.
correct code. STEP2 Press the [VOL ] button.
STEP5 Save the code. (Same as for 3-Digit
STEP4 Test functions. (Same as for 3-Digit STEP3 Press the [TV] button again.
Code Programming Method - Section A).
Code Programming Method - Section
The Component LED will blink twice
A). If any of the functions do not work
to confirm the programming.
Now, repeat the Auto-Search Method for
as they should, you need to find a
those Components you could not program
new code.
To return to original state:
earlier with the Pre-Programmed Method.
Once you have found the correct 3-
STEP5
If you wish to restore the CABLE channel
C. Finding a Component Button' s Setup digit code, save it by pressing the
control in TV mode, repeat the above steps but
[AUX] button one more time. The
Code Number
press [CBL] in
Component LED light will blink twice
to confirm the code was stored. Now
If you used the Auto-Search Method to
G. Programming Volume Control
when you press the AUX button, all
program a Component, you may not know
the buttons will work with that 5 th
Volume and Mute control are factory-
what the correct code number is. Here is a
Component.
programmed to automatically transfer to the
way for you to identify the code number, so
respective Component mode you select, as
you can record it for future reference. E. Programming the System On/Off Button
follows:
STEP1 Press the [COMPONENT] button (TV, This allows you to program the System On/Off
VCR, DVD or AUX) you want to verify button so it can send up to five power On/Off CBL : CBL
and the [OK/SEL] button simultaneously
commands with one button press. DVD: TV
for 3 seconds. The Component LED light
STEP1 Press the [CBL] button.
However, you can program the volume controls
will turn on for 30 seconds.
STEP2 Press the [SYSTEM ON/OFF] button
(Volume Up, Volume Down and Mute) from one
STEP2 Press the [INFO] button and count the
and the [OK/SEL] button simultaneously
Component to operate in another Component.
number of times the Component LED
for 3 seconds. The [CBL] button will turn
light blinks. This number indicates
If you wish to store the TV volume control in
on for 30 seconds.
the first digit of the code, followed by
CBL mode, use the following steps.
STEP3 Press the first [COMPONENT] button
the second and third, each separated
you want to store in the [SYSTEM
by a one second pause when the LED STEP1 Press the [CBL] button and the
ON/OFF] button and then the
will turn off.
[OK/SEL] button simultaneously for 3
[POWER] button. Repeat this for
seconds. The [CBL] Component LED
*Note : 10 blinks represents the number zero.
other Components until you have
will turn on for 30 seconds.
Example : One blink, (pause), eight blinks,
stored all the desired power
(pause) and three blinks, indicates commands into the [SYSTEM
STEP2 Press the [VOL ] button.
code number 183. ON/OFF] button.
STEP3 Press the [TV] button.
STEP4 Press the [CH ] button to save the
D. AUX Function: Programming a 5 th The Component LED will blink twice
power commands you stored. The
to confirm the programming.
Component
[CBL] button will blink twice to
confirm the commands have been
To return to original state:
You can take advantage of the AUX function to
saved.
program a 5 th Component such as a second
If you wish to restore the CBL volume control
TV, VCR, DVD or Audio Component.
F. Programming Channel Control in CBL mode, repeat the above steps but press
STEP1 Turn on the 5 th Component you want
[CBL] in
STEP3
to program (TV, VCR, DVD or Audio). You can program the channel controls
(Channel Up, Channel Down, Last and
STEP2 Press the [AUX] button and the H. Programming a 'Macro' button.
Numbers) from one Component to operate in
[OK/SEL] button simultaneously for 3
another Component mode. Default channel
If your remote model has custom-programmable
seconds.The [AUX] Component LED
control settings on the remote control are as
Macro buttons available, they can be
will turn on for 30 seconds.
follows:
programmed to act as a 'Macro' or Favorite
Press the [COMPONENT] button you
STEP3
CBL : CBL T V : CBL VCR: CBL
Channel button in CABLE mode. This allows you
want to setup. Point the remote control
DVD: DVD AUX: AUX
to program up to five 2-digit channels, four 3-digit
toward the Component and enter the 3-
digit code number assigned to your If you wish to store the TV channel control in channels or three 4-digit channels that can be
brand.
TV mode, use the following steps. accessed with one button press.
6
STEP1 Press the [CBL] button to select the CBL
Set-up Code Tables
mode.
CBL-CABLE Converters
STEP2 Press the [MACRO] button and [OK/SEL]
Manufacturer/Brand Set-Up Code Number
button simultaneously for 3 seconds.
MOTOROLA 002 111 148
The [CBL] button will turn on for 30
PACE 001 005 002
seconds. PIONEER 001 103 034 051 063 076 105
SAMSUNG 001 030
STEP3 Enter the the 2, 3 or 4-digit code for the SCIENTIFIC ATLANTA/CISCO 001 003 041 042 045 046
channel you want programmed first (for
TV
example, 007) using the Number Pad,
Manufacturer/Brand Set-Up Code Number
then press the [STOP] button. Then
A MARK 112 143
enter the code for the next channel (for
ABEX 025
example, 050), then press the [STOP] ACCURIAN 036
ADMIRAL 072 251 333
STEP3 . button. Repeat this process for the third
ADVENT 247 388
channel. The [CBL] button will blink
ADVENTURA 002
AIKO 103
once for each channel entered.
AKAI 116 146 248 404 405 473 475 323 387 391 615
ALBATRON 017
STEP4 Press the [CH ] button to store the
ALERON 028
channels that were selected. The [CBL]
AMERICA ACTION 043
button will blink twice to confirm the AMPRO 073
AMSTRAD 052
storage of commands.
ANAM 043 054 056 080 112
AOC 116 363 112 058 616
T V : TV VCR: TV To access the programmed channels, press
APEX 572
the [MACRO] button once. This will bring up APEX DIGITAL 006
AUX: AUX
AQUAVISION 573 574
the first channel. Press once again and it will
ASTAR 477
bring up the second channel. Press again and AUDIOVOX 076 454 388
AVENTURA 052
it will bring up the third channel.
AVIELO 627 628
AVION 441
AXION 039
I. Low Battery Warning
BELCOR 116
BELL&HOWELL 333 072
When the batteries are low and need to be
BENQ 423 600
replaced with fresh batteries, the Component
BOXLIGHT 266
BRADFORD 043
LED lights will blink 2 times in sequence
BROCKWOOD 116
whenever a [POWER] button is pressed to turn
BROKSONIC 238
BYDESIGN 031 032
on equipment.
CANDLE 116 002 003 363
CAPEHART 058
J. Memory Lock System CARY AUDIO DESIGN 266
CELEBRITY 001
CENTURION 116
This remote control is designed to retain
CETRONIC 043
programmed memory for 10 years even after
CHANGHONG 247
CITIZEN 116 002 003 363 043 258 103 143
batteries are removed from the remote control.
CLARION 043
CLASSIC 043
K. Record Your Component Set-up Codes
CLP CLASSIC 333
COBY 640 641
TV Set-up Code Number: COLORTYME 116
. CONCERTO 363
VCR Set-up Code Number: CONCIERGE 073
CONTEC 043 050 051
DVD Set-up Code Number: CORNEA 116
CORONADO 143
AUX Set-up Code Number: CRAIG 043 054
CROSLEY 164
For additional information about your remote CROWN 043 143
CURTIS MATHES 116 258 363 143
control, go to www.universalremote.com
CXC 043
CYBERHOME 015
DAEWOO 363 016 043 044 076 103 114 125 127 143
DAYTRON 363 143
DELL 320 164 363 618
TV TV
Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number
DIGITAL PROJECTION 570 LITEON 268
DIMENSIA 333 LODGENET 072
DREAMVISION 235 LOEWE 164
DUKANE 011 025 LOGIK 072
DUMONT 116 073 LUXMAN 363
DURABRAND 096 052 LXI 166 007 138 052 251 333 164
DWIN 257
MAGNAVOX 164 059 116 003 060 061 363 127 022 333 094
DYNASTY 043
226 390 467 431
DYNEX 400 MAJESTIC 333 072
EIKI 187 MARANTZ 116 164 281 562 584
ELECTROBAND 001 MATSUI 164
ELECTROGRAPH 466 MATSUSHITA 080
ELECTROHOME 143 024 076 196 MAXENT 242
ELEKTRA 072 MEGATRON 116 011
ELEMENT 363 494 526 622 MEMOREX 007 072 363
EMERSON 028 048 043 155 005 116 363 047 050 051 076 MGA 116 363 024 028 042
096 143 153 154 052 514 MIDLAND 333 073
ENVISION 116 MINTEK 362
EPSON 324 590 MINUTZ 008
ESA 323 MISAKAI 052
FISHER 007 057 MITSUBISHI 124 109 024 028 040 042 146 363 348 450
FUJITSU 246 198 410
MONIVISION 017
FUNAI 028 043 052
MONTGOMERY WARD 333 072
FUSION 642 MOTOROLA 081
FUTURETECH 043 MTC 116 363 258
GATEWAY 242 268 MULTITECH 043
GE 073 116 008 009 034 056 074 155 333 363 NAD 138 025
GEM 391 NEC 272 197134 116 040 016 024 056 019 262 236
GIBRALTER 116 073 281 575
GO VIDEO 026 NET TV 242
GOLDSTAR 113 116 102 363 106 112 127 143 NEXUS 620 454
GRUNPY 028 043 NIKEI 043
HAIER 363 501 623 NIKKO 116
HALL MARK 363 NIKO 527
HANNSPREE 349 381 NORCENT 390
HARLEY DAVIDSON 028 NORWOOD MICRO 027
HARVARD 043 NTC 103
HAVERMY 081
NUVISION 351 567
HELLO KITTY 076
OLEVIA 432 363 333
HIMITSU 043 ONKING 043
HISENSE 419 442 619 630 631 ONWA 043
HITACHI 011 166 009 010 012 023 075 143 158 072 363 OPTIMUS 025
250 587 613 OPTOMA 265 249
HP 378 316 327 421 OPTONICA 019 251
HUMAX 518 ORION 096
HYPERION 609 PANASONIC 080 034 056 164 208 359 552 524 607
HYUNDAI 337 338 PHILCO 116 003 059 060 164 363 024 056
ILO 472 399 PHILIPS 164 005 093 038 116 003 363 059 127 206 431
INFINITY 164 333 161 594 629
INFOCUS 333 230 547 548 470 532 564 595 PILOT 116
INITIAL 035 282 PIONEER 234 135 025 018 023 116 393 272 520 582
INSIGNIA 350 400 052 164 403 454 457 604 617 POLAROID 388 323 328 353 354 355 356 494 387 391 505
INTEQ 073 506 508
JANEIL 002
PORTLAND 363 143
JBL 164
PRINCETON 004
JCB 001 PRISM 034
JCPENNEY 024 116 008 009 030 065 258 143 333 363 PROSCAN 333
JENSEN 013 PROTON 363 112 058 143 171 172 033 528
JVC 038 034 001 083 199 210 533 581 639 406 PROTRON 392 398 498 499 500
KAWASHO 116 001 PROVIEW 494
KEC 043 PROX 572
KENWOOD 116 001 PULSAR 116 073
KLEGG 466 QUASAR 034 056 606
KLOSS 002 059 RADIO SHACK 019 363 143 043 127
KMC 143 RCA 333 065 116 363 024 056 152 023 074 161 588
KNOLL SYSTEMS 230 REALISTIC 007 019 043 047
KONKA 457 REVOLUTION HD 466
KREISEN 530 RUNCO 182 073 395 416 072 342
KTV 043 116 143 154
SAMPO 116 058 363 242
KURAZAI 072
SAMSUNG 258 050 089 105 363 127 143 333 228 229 515
LG 363 113 116 102 106 112 127 143 569 284 SAMSUX 116