Universal Remote Control UR5U-8500 Operating Instructions

Introduction
1
Operating Instructions For
CLIKR TM -5
The UR5U-8500 is designed to
CLIKR ™ -5
operate Scientific-Atlanta, Pioneer, Voyager
and Pace Micro digital set top boxes
(including DVR & HD), plus the majority of TV,
Cable Remote Control
VCR, DVD and AUDIO equipment on the
market as shown below.
CABLE : Cable Converters
UR5U-8500
VCR : VCRs and TV/VCRs
AUX : Audio Receivers and DVRs, etc.
2 Replacing Batteries
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
Operations
3
DEFAULT STATES:
Component Default: CABLE
Channel Default: CABLE channel and number
keys through the CABLE. You have the option
of controlling your CABLE channel and
number keys through the TV or VCR. Refer to
section F for programming steps.
Volume Default: TV volume and mute keys
through the TV. You have the option of
Universal Remote Control, Inc.
controlling your TV volume and mute through
the Cable box, VCR or DVD. Refer to section G
www.universalremote.com
for programming steps.
OCE-0045A REV 02 (05/06/06)
Button Functions
4
TV : Televisions
DVD: DVD Players
5 Programming the Remote Control
There are two ways you can program your CLIKR TM -5 remote:
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Auto-Search Method scans through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, a component LED will light for
30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit setup
mode and you will need to start over.
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote.
STEP2 Press the [COMPONENT] button (TV, STEP5 Save the code. (Same as for 3-Digit Code
VCR, DVD or AUX) to be programmed and
Programming Method - Section A).
[OK/SEL] button simultaneously for 3
Now, repeat the Auto-Search Method for those
seconds. The Component LED light will
Components you could not program earlier
turn on for 30 seconds indicating the unit
is ready to be programmed. with the Pre-Programmed Method.
STEP3 Point the remote control toward the
Component and enter the 3-digit code C. Finding a Component
number assigned to your brand.
Button's Setup Code Number
*Note : If the 3-digit code number you just entered
If you used the Auto-Search Method to program a
is correct, the Component will turn Off. If it
Component, you may not know what the correct code
did not turn Off, continue entering code
number is. Here is a way for you to identify the code
numbers listed for that brand until the
number, so you can record it for future reference.
Component turns Off.
STEP1 Press the [COMPONENT] button (TV, VCR,
STEP4 After you've entered the correct code
DVD or AUX) you want to verify and the
number and the Component has turned
[OK/SEL] button simultaneously for 3
Off, press the [POWER] button to turn the
Component back On. Now it's time to test seconds. The Component LED light will turn
the VOLUME and CHANNEL buttons for
on for 30 seconds.
the TV (or PLAY and STOP buttons for
Press the [INFO] button and count the
STEP2
VCR and DVD) to make sure they all work.
number of times the Component LED light
If any of the functions do not work as they
blinks. This number indicates the first digit
should, repeat from STEP 3 using the next
of the code, followed by the second and
3-digit code number listed for that brand.
third, each separated by a one second
STEP5 Once you have found the correct 3-digit
pause when the LED will turn off.
code, save it by pressing the same
[COMPONENT] button one more time.
*Note : 10 blinks represents the number zero.
The Component LED light will blink twice
Example :One blink, (pause), eight blinks, ( pause)
to confirm that the code was successfully
and three blinks, indicates code number
stored.
183.
Now, program the rest of your Components
D. AUX Function: Programming a 5
by repeating STEPS 1-5.
Component
*Note : If the Pre-Programmed Method did not
work, or if the Code Tables do not list your
You can take advantage of the AUX function to
Component brand, use the Auto-Search
program a 5 th Component such as a second TV, VCR,
Method as explained in Section B.
DVD or Audio Component.
B. Auto-Search Method STEP1 Turn on the 5 th Component you want to
program (TV, VCR, DVD or Audio) using
STEP1 Turn on the Component you want to
your old remote.
program (TV, VCR, DVD or AUX) using
your old remote. STEP2 Press the [AUX] button and the [OK/SEL]
button simultaneously for 3 seconds.The
STEP2 Press the [COMPONENT] button (TV,
[AUX] Component LED will turn on for 30
VCR, DVD or AUX) to be programmed and
seconds.
[OK/SEL] button simultaneously for 3
seconds. The Component LED light will
STEP3 Press the [COMPONENT] button you want
turn on for 30 seconds indicating the unit
to setup. Point the remote control toward
is ready to be programmed.
the Component and enter the 3-digit code
STEP3 Point the remote toward the Component
number assigned to your brand.
and press the [CH ] or [CH ] button
one step at a time or keep it pressed. The *Note : If the 3-digit code number you just entered is
remote will emit a series of ON/OFF the correct number, the Component will turn
commands. Release the [CH ] or
Off. If it did not turn Off, continue entering
[CH ] button as soon as the Component
code numbers listed for that brand until the
turns Off.
Component turns Off
STEP4 Test functions. (Same as for 3-Digit Code
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any
Programming Method - Section A). If any
of the functions do not work as they
of the functions do not work as they should,
should, repeat from STEP 3 using [CH ]
you need to find a new code.
or [CH ] buttons to find the correct code.
STEP5 Once you have found the correct 3-digit
CBL : TV T V : TV
code, save it by pressing the [AUX] button
DVD : TV AUX : AUX
one more time. The Component LED light
will blink twice to confirm the code was If you wish to store the CBL volume control in CBL
stored. Now when you press the AUX
mode, use the following steps.
button, all the buttons will work with that 5 th
Press the [CBL] button and the [OK/SEL]
STEP1
Component.
button simultaneously for 3 seconds. The
[CBL] Component LED will turn on for 30
E. Programming the System On/Off Button
seconds.
This allows you to program the System On/Off button
Press the [VOL +] button.
STEP2
so it can send up to five power On/Off commands
STEP3 Press the [CBL] button.
with one button press.
The Component LED will blink twice to
STEP1 Press the [CBL] button.
confirm the programming.
STEP2 Press the [SYSTEM ON/OFF] button and the
To return to original state:
[OK/SEL] button simultaneously for 3
seconds. The [CBL] button will turn on for If you wish to restore the TV volume control in CBL mode,
30 seconds.
repeat the above steps but press [TV] in
STEP3 Press the first [COMPONENT] button you
want to store in the [SYSTEM ON/OFF] H. Programming a 'Macro' or Favorite
button and then the [POWER] button.
Channel
Repeat this for other Components until you
In CBL mode, the M1, M2, HELP and BLANK
have stored all the desired power
buttons can be programmed to act as a 'Macro' or
commands into the [SYSTEM ON/OFF]
button. Favorite Channel button. This allows you to send
up to 10 commands with one button press.
STEP4 Press the [CH+] button to save the power
commands you stored. The [CBL] button
STEP1 Press the [CBL] button to select the CBL
will blink twice to confirm the commands
mode.
have been saved.
STEP2 Press the M1, M2, HELP or BLANK button
and [OK/SEL] button simultaneously for 3
F. Programming Channel Control
seconds. The [CBL] Component LED will
turn on for 30 seconds.
You can program the channel controls (Channel Up,
th
Channel Down and Last) from one Component to
STEP3 Press up to 10 buttons you wish to store.
operate in another Component mode. Default channel
The [CBL] Component LED will blink once
control settings on the remote control are as follows:
for each command entered.
CBL : CBL T V : CBL VCR : CBL
Press the [CH+] button to store the
STEP4
DVD : DVD AUX : AUX
commands that were selected. The [CBL]
Component LED will blink twice to
If you wish to store the TV channel control in TV
confirm the storage of commands.
mode, use the following steps.
STEP1 Press the [TV] button and the [OK/SEL]
I. Low Battery Warning
button simultaneously for 3 seconds. The
[TV] Component LED will turn on for 30 When the batteries are low and need to be
seconds. replaced with fresh batteries, the Component LED
lights will blink 2 times in sequence whenever a
Press the [VOL -] button.
STEP2
[POWER] button is pressed to turn on equipment.
Press the [TV] button again.
STEP3
The Component LED will blink twice to
J. Memory Lock System
confirm the programming.
This remote control is designed to retain
To return to original state:
programmed memory for 10 years even after
If you wish to restore the CABLE channel control in
batteries are removed from the remote control.
TV mode, repeat the above steps but press [CBL]
in .
STEP3 K. Record Your Component Set-up Codes
G. Programming Volume Control
TV Set-up Code Number:
You can program the volume controls (Volume Up, VCR Set-up Code Number:
Volume Down and Mute) from one Component to
DVD Set-up Code Number:
operate in another Component mode. Default volume
AUX Set-up Code Number:
control settings on the remote control are as follows:
VCR : TV
STEP3 .