Advertisement
Motherboard Layout
主機板構造圖 / Motherboard-Layout / Carte mère / layout della scheda madre / tarjeta madre /
Disposição da placa-mãe / 메인 보드 레이아웃 / マザーボードのレイアウト
Top View
5-Pin CPU Fan Connector
LGA1151 Package
1
CPU Socket
(CPU_FAN2)
2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A1, DDR4_B1)
4-Pin CPU Fan Connector (CPU_FAN1)
USB 2.0 Header (USB_5_6)
COM Header (COM1)-(Optional)
(for H110M-STX/COM and Q170M-STX)
System Panel Header (PANEL1)
Key E 2230 M.2 Slot
Chassis Intrusion Header (CI1)
6
(for WiFi + BT Module)
SATA3 Connectors
Intel H110 Chipset
Key E 2280 M.2 Slot
(for PCIe Gen3x4 M.2 SSD)
Onboard Connectors
主機板元件 / Onboard-Anschlüsse / Connecteurs à bord / Connettori a bordo / Conectores a bordo /
Conectores de bordo / 온보드 커넥터 / オンボードコネクタ
5-Pin CPU Fan Connector (CPU_FAN2)
COM Header (COM1)-(Optional)
1
4
1
NC
RI
RTS
CT S
GND
GND
DS R
TXD
DT R
GND
DCD
FAN_VOLTAGE
RX D
FAN_SPEED
1
FAN_SPEED_CONTROL
4-Pin CPU Fan Connector (CPU_FAN1)
System Panel Header (PANEL1)
2
5
1
GND
PLED +
+12V
PLED -
2
CPU_ FA N_SPEED
PWRBTN #
3
GN D
FA N_SPEED_CONTROL
4
1
GN D
USB 2.0 Header (USB_5_6)
RESET #
3
GN D
HDLED-
HDLED+
DUMMY
GND
GND
P+
P+
P-
P-
U
SB_PW R
U SB_PW R
1
Hardware Installation
Begin Installation
A
2
3
1. Unscrew the four screws of the back panel.
4
B
Installing the CPU
5
1
A
Bottom View
7
Installing the CPU Fan and Heatsink
C
1
Chassis Intrusion Header (CI1)
6
GND
1
Signal
SATA3 Connectors
7
*
e DeskMini 110 series supports both Intel CPU Box Fan (65W) and third-party CPU fan cooler.
Please note that the DeskMini 110 series chassis has 52mm height limitation for the CPU fan cooler.
D
Installing Memory Modules (DDR4 SO-DIMM)
1
20
PIN
Signal Name
PIN
Signal Name
1
1
GND
11
N/A
5V
2
LVDS_TX+
12
3
LVDS_TX-
13
5V
4
GND
14
5V
GND
5
15
5V
6
LVDS_RX-
16
5V
7
LVDS_RX+
17
N/A
8
18
GND
GND
9
GND
19
GND
*
e DeskMini 110 series requires DDR4 SO-DIMM.
10
GND
20
GND
*For dual channel con guration, you always need to install identical (the same brand, speed, size and chip-type) DDR4 SO-DIMM pairs.
硬體安裝 / Hardware-Installation / Installation du matériel / Installazione hardware / Instalación de hardware /
Instalação de hardware / 하드웨어 설치 / ハードウェアのインストール
2. Pull out the motherboard tray while holding the handle .
2
3
4
5
B
2
3
2
3
Installing the WiFi Module
E
1. Insert the WiFi Module Card into the M.2
2. Tighten the screw to secure the WiFi
Slot for WiFi + BT Module.
Module Card to the motherboard.
Installing the M.2 SSD
F
1. Locate the M.2 slot on the motherboard.
2. Carefully insert the M.2 SSD into the slot.
Installing the 2.5-inch HDD/SSD
G
B
A
1. Locate the drive mounting trays.
2. Place a HDD/SSD on the tray A shown in
Step 1. Align the drive screw holes with
those in the drive mounting tray.
en
secure the HDD/SSD with two screws.
4. Place another HDD/SSD on the tray B
5. Connect the SATA Data and Power
shown in Step 1.
en turn the motherboard
Cable to the HDD/SSD.
tray upside down and secure the HDD/SSD
with the four screws.
*Removing the motherboard before
installing the second HDD/SSD.
3. Attach the SMA Wi-Fi Antenna Cables to the
WiFi Module.
3. Tighten the screw to secure the M.2 SSD
to the motherboard.
3. Connect the SATA Data and Power
Cable to the HDD/SSD.
6. Connect the other end of the SATA
Cables to the SATA Connectors on the
motherboard.
Advertisement
