Denon AVR-X6400H Service Manual page 159

Paths to be confirmed Display
Analog Amp Assign
8 (Amp Assign : fig.08
A08:ASSIGN-Z3
ZONE3)
Analog Amp Assign
(Amp Assign :
9 fig.09
A09:ASSIGN-Z2/3M
ZONE2/ZONE3-
MONO)
Amp Assign
fig.10a
10 (Amp Assign :
A11:ASSIGN-BiAMP
fig.10b
BiAMP)
fig.11a
11 Front Height
A14:FRONT HEIGHT
fig.11b
Settings
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : STEREO
Z3 Source : Source
Amp assign : 9.1ch + ZONE3
Speaker for ZONE3 : Height2
Floor Layout : 5ch
Height Sp : 4ch
Dolby Sp : None
Height Layout : Front Height/Rear Height
MAIN ZONE : On
ZONE2 : Off
ZONE3 : On
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : STEREO
Z2 Source : Source
Z3 Source : Source
Amp assign : 9.1ch + ZONE2/3
Speaker for ZONE2/3 : Height2
Floor Layout : 5ch&SB
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height/Rear Height
MAIN ZONE : On
ZONE2 : On
ZONE3 : On
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : MULTI CH STEREO
Amp assign : 9.1ch + BiAMP
Speaker for Bi-Amp : S.Back
Floor Layout : 5ch
Height Sp : 4ch
Dolby Sp : None
Height Layout : Front Height/Rear Height
MAIN ZONE : On
ZONE2 : Off
ZONE3 : Off
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : MULTI CH STEREO
Amp assign : 11.1ch
Floor Layout : 5ch&SB
Height Sp : 4ch
Dolby Sp : None
Height Layout : Top Front & Top Rear
Speaker Select=Floor & Height
MAIN ZONE : On
ZONE2 : Off
ZONE3 : Off
159
What to confirm
・ Analog input ⇒ Speaker output (Height 2 (ZONE3) L/R)
・ Analog input ⇒ Pre OUT output (ZONE3 L/R)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
・ Analog input ⇒ Speaker output (Height2 (ZONE2 MONO L), Height2 (ZONE3 MONO) R)
・ Analog input ⇒ Pre OUT output (ZONE2 L/R MONO, ZONE3 L/R MONO)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
・ Analog input ⇒ Speaker output (S.Back L/R)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
・Analog input ⇒ Speaker output (Height1 L/R (Top Front), Height2 L/R (Top Rear))
・ Analog input ⇒ Pre OUT output (Height1 L/R (Top Front), Height2 L/R (Top Rear))
・ Pre OUT output
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)