Samsung SCC-C6405(P) Owner's Instructions Manual
Smartdome camera
Hide thumbs
Also See for SCC-C6405(P):
- Owner's instructions manual (31 pages) ,
- Owner's instructions manual (151 pages)
Related Manuals for Samsung SCC-C6405(P)
Summary of Contents for Samsung SCC-C6405(P)
- Page 1 SmartDome Camera SCC-C6405(P) Owner’s Instructions êÛÍÓ‚Ó‰ÒÚ‚ÓÔÓθÁÓ‚‡ÚÂÎfl Instrukcja obs∏ugi Part : AB68-00504D (04) Printed in China...
-
Page 2: Important Safety Instructions
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturer's instructions. -
Page 3: Fcc Statement
9. If this product fails to operate normally, contact the store of purchase or your nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.) 10. -
Page 4: Before Usage
Before Usage This is a basic instruction manual for the SCC-C6405(P) user. It contains all the instructions needed to use the SCC-C6405(P) from a simple introduction of the control locations and functions of the SCC-C6405(P) to installation methods in the set up menu. We recommend all users of the SCC-C6405(P) from the advanced user who has used similar cameras before to the general user to read the instruction manual before using. -
Page 5: Table Of Contents
Table of contents Before Usage ...1-1 Chapter 1 SCC-C6405(P) Overview ...1-5 SCC-C6405(P) Introduction ...1-6 Locations of Control ...1-7 FRONT...1-7 BACK ...1-8 ADAPTER CONNECTION...1-9 INITIAL SETTING ...1-10 Setting RS-422A/RS-485 termination ...1-11 Chapter 2 SCC-C6405(P) Installation ...2-1 Before Installing ...2-2 Preparing the Cables ...2-3 Cable Connection ...2-4 Installing SCC-C6405(P)...2-5 Installing the Camera ...2-8... -
Page 6: Chapter 1 Scc-C6405(P) Overview
Chapter 1 SCC-C6405(P) Overview In this chapter we will briefly introduce the SCC-C6405(P) and show main functions, locations of control and Switch Setting. SCC-C6405(P) Introduction SCC-C6405(P) is a zoom lens built in smart dome camera which provides you with the best monitoring function in connection with CCTV at banks or companies. -
Page 7: Locations Of Control
Locations of Control FRONT BACK AC 24V POWER AC 24V POWER... -
Page 8: Adapter Connection
Use number 1~4 PIN of SW704 to set communication Protocol. PIN1 PIN2 PIN3 PIN4 Comp A : SAMSUNG HALF B : SAMSUNG FULL SEE INSTRUCTION MANUAL 1 2 3 4 5 6 7 8 (x100) (x10) SW701 SW702 SW703 (BOTTOM VIEW) Baud Rate Setting Use PIN 5 and 6 of SW704. -
Page 9: Setting Rs-422A/Rs-485 Termination
Setting RS-422A/RS-485 termination As it is shown in the structure map, when Controller and RS-422A/RS- 485 is connected it should be terminated according to the Cable feature of impedance on the each end of the transmitting line to transfer the signals in long distance by controlling the reflection of the signals to the lowest. -
Page 10: Before Installing
Before Installing Checking Package Contents Please check that all components listed below are included in the package: SCC-C6405(P) Bracket anchor Owner’s Instructions AC 24V POWER Screws Cover Body Camera Holder Adapter Board Preparing the Cables To install and use the SCC-C6405(P), the following cables should be prepared. -
Page 11: Cable Connection
Cable Connection 1. First, connect one end of the BNC video cable connector to the Video Output Terminal (VIDEO OUT) 2. Then, connect the other end of the connector to the Video Input Terminal of the monitor. 3. Now connect the Power Adapter Cable. - Page 12 3) INDOOR HOUSING (SHG-120) This housing is used for installing the SmartDome Camera to an indoor wall or a ceiling. 4) OUTDOOR HOUSING (SHG-220) This housing is used for installing the SmartDome Camera to an outdoor wall or a ceiling. 5) CEILING MOUNT ADAPTOR (SADT-100CM) This adaptor is used for installing the indoor housing or the outdoor housing for the SmartDome Camera to a concrete ceiling.
-
Page 13: Installing The Camera
Installing the Camera 1. [Figure 1] Install the structure on the ceiling. (Refer to Installation reference for the Length of the structure) * Built in by the builder of the structure [Figure 1] 2. Make a hole in the ceiling where the camera will be installed. (The hole should be about ø185) 3. -
Page 14: Chapter 3 Setup Menu Overview
Chapter 3 Setup Menu Overview In this chapter, we will look over the Setup Menu of the SCC-C6405(P), First we'll look over the overall structure of the Setup Menu, and then we'll look at the functions of each menu. Structure of the Setup Menu CAMERA SET CAMERA ID ON.../OFF... -
Page 15: Camera Id
ALARM SET ALARM PRIORITY SET ALARM1 1~4 ALARM2 1~4 ALARM3 1~4 ALARM4 1~4 EXIT ALARM IN SET ALARM1 NO/NC/OFF ALARM2 NO/NC/OFF ALARM3 NO/NC/OFF ALARM4 NO/NC/OFF EXIT ALARM OUT SET ALARM1 1~3 ALARM2 1~3 ALARM3 1~3 ALARM4 1~3 MOTION 1~3 EXIT AUTO SET ALARM1 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4 ALARM2 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4... -
Page 16: V-Sync
(CAMERA SET) (CAMERA ID) A B C D E F G H I J K L CAMERA ID ON... ➜ M N O PQ R S T U V W X V-SYNC Y Z 0 1 2 3 4 5 6 7 8 9 COLOR/BW COLOR MOTION DET... -
Page 17: Motion Det
MOTION DET In MOTION DET, you can set the Motion Detection function, Motion Detection Sensitivity, and the Area of Motion Detection. If the Motion Detection function is set, the movement of an intruder can be detected. When motion is detected, it sets off the Alarm signal of the Controller. -
Page 18: Video Set
2. VIDEO SET MENU IRIS There is a function to automatically adjust IRIS to the incoming light level. Owing to this function, you may set up the brightness level yourself. The ALC(Auto Light Control) menu allows you for video output level setup. The WDR(Wide Dynamic Range) menu allows you to set up the WDR level and the FLICKERLESS function. -
Page 19: Agc
The AGC menu was designed to provide you with brighter screen supposed you photographed any subject in the dark resulting in less brighter image than regulated. AGC menu setup is available only when the SHUTTER menu is set to Fast Shutter or Off. Press either Left and Right to go to LOW or HIGH and the AGC function will be activated. -
Page 20: Dis
You can select one of four modes for white balance adjustment as follows: - ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the color temperature is monitored continuously and thereby white balance is set automatically. The following are the approximate supported color temperature ranges in these modes. -
Page 21: Preset
3. PRESET This is the menu that user sets the PAN/TILT location, Zoom/Focus, and screen condition, so the camera can monitor the presetting area on demand. A total of 128 presets are available. Among the 128 PRESETS, PRESET 1: ALARM1, PRESET 2: ALARM2, PRESET 3: ALARM3, PRESET 4: ALARM4,PRESET 5: set as special preset corresponding MOTION. -
Page 22: Zone Set
4. ZONE SET The ZONE SET menu includes the setup of PRIVACY ZONE, ZONE DIRECTION, and ZONE AREA. * * MAIN MENU * * CAMERA SET... VIDEO SET... ➜ PRESET... ZONE SET... Press AUTO SET... [Enter] ALARM SET... OTHER SET... SYSTEM INFO... -
Page 23: Set Zone Area
SET ZONE AREA Press [ENTER] at the “SET ZONE AREA...” position to enter the PRIVACY ZONE setup screen. Control PAN/TILT/ZOOM to select 4 apexes of the PRIVACY ZONE area and the rectangular PRIVACY ZONE area will be completed. PRIVACY ZONE SET 0 PRIVACY ZONE P/T 1 SET ZONE AREA ON... -
Page 24: Zone Dir Set
ZONE DIR SET Press the [Enter] key in the “ZONE DIR SET ON…” mode to enter the NORTH SET screen. MAP. Move PAN to set the NORTH position and press [ENTER]. Based on the North position,the direction of N(North), NE(North-East), E(East), SE(South-East), S(South), SW(South-West), W(West), NW(North-West) is displayed whenever you move PAN. -
Page 25: Auto Set
5. AUTO SET The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is able to set up the AUTO PLAY motion. AUTO PAN After selecting the locations of two points (PAN/TILT) of START and END, it loops continuously in the set up SPEED. The number of AUTO PAN is up to 4. -
Page 26: Scan
* * MAIN MENU * * (AUTO SET) CAMERA SET... VIDEO SET... AUTO PAN ➜ PRESET... PATTERN ZONE SET... SCAN Press AUTO SET... AUTO PLAY [Enter] ALARM SET... OTHER SET... SYSTEM INFO... ➜ PATTERN SET 1 PATTERN SET 1 SET START POSITION After PATTER AND ENTER START... -
Page 27: Alarm Set
6. ALARM SET It consists of 4 ALARM INPUTs and 3 ALARM OUTs.It can sense an ALARM input from exterior SENSORs and it performs with PRESET or PATTERN function and outputs the ALARM OUT signals. The Alarm will be recognized only when its input lasts more than 150ms and the alarm operation time depends on the Preset Dwell time corresponding to the alarm and whether AUTO is involved. -
Page 28: Turbo P/T
CAMERA VER. V1.000 PRESET... EEPROM VER. V1.000 ZONE SET... Press PROTOCOL AUTO SET... [Enter] COMM. TYPE RS-485, HALF BAUD RATE ALARM SET... ADDRESS OTHER SET... SYSTEM INFO... ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ V1.000 V1.000 SAMSUNG 38400 3-30... -
Page 29: Short Keys
9. SHORT KEYS SSC-1000 or SSC-2000 Controller supports the following short keys. Function CAMERA SET… COLOR/BW COLOR [PRESET] + [1] + [2] + [8] + [Enter] COLOR/BW [PRESET] + [1] + [2] + [9] + [Enter] COLOR/BW AUTO [PRESET] + [1] + [3] + [0] + [Enter] VIDEO SET…... -
Page 30: Product Specifications
3-33 Product specifications SCC-C6405 Items Contents Product Type - Zoom lens single body WDR SmartDome CAMERA Power Input - AC 24 ± 10% (60Hz ± 0.3Hz) Power Consumption - 18W Broadcasting Type - NTSC STANDARD COLOR SYSTEM Image Device - 1/4 inch WDR compatible Exview HAD CCD Effective Pixels - 768(H) x 494(V) Scanning Mode... - Page 31 - Fan 3-35 Remark • The copyright of the manual belongs to Samsung Electronics Co., Ltd. • Without the permission of Samsung Electronics it cannot be reproduced electronically, mechanically, audibly, or by any other method. • This manual will be modified according to product enhancements.