Diagnostic Mode; (Video/Audio (Signal) Path Confirmation Mode) - Denon AVR-1613 Service Manual

4. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode)
This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting)
Confirming the operation of unit can be easily done after repair.
Backup data will not be lost.
4.1. Starting diagnostic mode
Press the X button to turn on the power while pressing the "DIMMER", "STATUS" and "ZONE2 SELECT"(only AVR-1713E3)/ "TUNER PRESET CH +"(expect AVR-1713E3).
Press the SOURCE SELECT 0 / 1 to select "1.SERVICE CHECK", then press the "STATUS" button to set.
TUNED, STEREO and RDS are lit in FL display.
4.2. Canceling diagnostic mode
Turn off the power by pressing the ON/Standby button.
4.3. Operation
When you perform remote operation in accordance with the instructions in "Details of how to operate remote controller" *a) in the table below using the remote control unit (RC-1156).
You will find using another remote control unit with the macro functions very useful. To use the macro functions, program a macro function to output a remote control code in accordance with the steps in *b) in the table below.
4.4. Video system confirmation items
fig.XX : Refer to the block diagram of the fig.XXth.
Confirmation item
Setting and display
Analog Video (signal) Path Display:
V 0 1
1
fig.1
HDMI (signal) Path Display:
V 0 1
2
fig.2
OSD FUNCTION
Menu : ON
Display:
V 0 2
3
fig.3
CEC FUNCTION
HDMI Control : ON
(Control Monitor : HDMI Monitor) Display:
4 fig.4 V 0 3
HDMI Audio (signal) Path Audio : AMP(When checking the audio output
(Audio : AMP) from AMP)
fig.5a Display:
5
V 0 5
fig.5b
HDMI Audio (signal) Path Audio : TV(When checking the audio output
(Audio : TV) from TV)
Display:
6
fig.2
V 0 6
Details of how to operate remote controller *a)
1.Press [AMP]
2.Press [ZONE SELECT], Select "MAIN"
D V D
3.Press [1/./]
4.Press [DVD]
1.Press [AMP]
2.Press [ZONE SELECT], Select "MAIN"
D V D
3.Press [1/./]
4.Press [DVD]
1.Press [AMP]
2.Press [ZONE SELECT], Select "MAIN"
3.Press [2/ABC]
D V D
4.Press [DVD]
5.Press [AMP]
6.Press [MENU]
1.Press [AMP]
2.Press [ZONE SELECT], Select "MAIN"
3.Press [3/DEF]
D V D
4.Press [DVD]
1.Press [AMP]
2.Press [ZONE SELECT], Select "MAIN"
3.Press [5/JKL]
4.Press [DVD]
D V D
1.Press [AMP]
2.Press [ZONE SELECT], Select "MAIN"
3.Press [6/MNO]
4.Press [DVD]
D V D
Output sequence of remote control codes
※ It is useful to form a macro program. *b)
qKEY 1/CODE1 (Main Zone) ·Input : CVBS / Output : CVBS
Initialization
wDVD (Main Zone)
qKEY 1/CODE1 (Main Zone)
·Input HDMI / Output : HDMI
( b As the input source, you can switch from DVD to other ones.)
Initialization
wDVD (Main Zone)
qKEY 2/ABC (Main Zone)
·OSD Display / Output : HDMI
( b As the input source, you can switch from DVD to other ones.)
Initialization
wDVD (Main Zone)
eGUI MENU (Main Zone)
qKEY 3/DEF (Main Zone) · When the power supply of a TV is put in the standby mode, make sure
Initialization & CEC Control ON that the power supply of this unit is also put in the standby mode.
( b As the input source, you can switch from DVD to other ones.)
wDVD (Main Zone)
qKEY 5/JKL (Main Zone) ·Input : HDMI (Signal of PCM, DolbyDigital or DTS) / Output : Speakers
Initialization & Select Audio AMP ·Input : HDMI (Signal of HD Audio) / Output : Speakers
( b As the input source, you can switch from DVD to other ones.)
wDVD (Main Zone)
qKEY 6/MNO (Main Zone)
· Input : HDMI (Signal of PCM or DolbyDigital or DTS) / Output : HDMI
Initialization & Audio Select TV (Audio output from connected TV)
( b As the input source, you can switch from DVD to other ones.)
wDVD (Main Zone)
25
Contents of confirmation
Remarks