Using The Tv Buttons On The Remote Control; Basic Connections/Auto Setup - Samsung DVD-V2000 Instruction Manual

Using the TV Buttons on the Remote Control

Your VCR remote control will work with Samsung televisions and
compatible brands.
To determine whether your television is compatible, follow the instructions
below.
POWER OPEN/CLOSE
1 Switch your television on.
1
2 3
SCREEN FIT TV/VCR 2
Point the remote control towards the television.
SHUTTLE
4 5 6
M O D E /
REPEAT AUDIO
3 Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
7 8
9
appropriate numeric buttons.
ZOOM
ANGLE
Brand
3D SOUND CLEAR
TV MUTE INPUT SEL.
0
100+
2
SAMSUNG
DVD VCR SELECT TV
SHARP
3
VIEW
SONY
+
DIGEST DISPLAY
RCA
VOL CH/TRK
TOSHIBA
F.ADV/SKIP -
3
PANASONIC
JVC
HITACHI
MITSUBISHI
SELECT
DVD VCR TV
NEWSAN
VIEW
4
+
DIGEST DISPLAY Result:
VOL CH/TRK
F.ADV/SKIP -
4
If several codes are indicated for your television brand, try
each one in turn until you find one that works.
REC DISC MENU
When you change the batteries in the remote control, you
must reprogram the code, following the same procedure.
7 8 9
ZOOM ANGLE
3D SOUND CLEAR You can then control the television using the following buttons.
TV MUTE
INPUT SEL.
100+ 0
5
DVD VCR SELECT TV
Button
VIEW
POWER
+
DIGEST DISPLAY
VOL CH/TRK
INPUT
F.ADV/SKIP
-
+ –
VOL or
CH (" or ❷)
MUTE
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
12
Codes Brand Codes
01, 14, 15, 23 LOEWE 28
02, 16, 22 ZENITH 17
03 LG 06, 08, 18
07, 29 MAGNAVOX 04
09 EMERSON 21
12, 24 SANYO 05, 20
11 DAEWOO 19
10 NOBLEX 25
13 TELEFUNKEN 26
27
If your television is compatible with the remote control, it
will switch off. It is now programmed to operate with the
remote control.
Function
Used to switch the television on and off.
Used to select an external source.
Used to adjust the volume of the television.
Used to select the required channel.
Used to toggle the sound on and off.

Basic Connections/Auto Setup

In this section, you will connect the DVD-VCR to your television
and run Auto Setup, which automatically searches for channels and
sets the player's internal clock.
NOTES:
• Advanced Connections are covered in Appendix A.
• Even if you plan to use the S-Video or Component Video Outputs,
you MUST connect the DVD-VCR to your television with
either the standard RF or the Line Out connection. This
enables you to operate the DVD-VCR setup menus.
1 Connect Antenna/Cable to DVD-VCR
Connect the RF antenna cable from your indoor/outdoor antenna or
cable wall outlet to the IN (FROM ANT.) jack on the back panel of
the DVD-VCR.
2 Connect DVD-VCR to TV
Choose one of the following methods to connect the DVD-VCR to
your TV:
RF Connection
Connect the supplied RF antenna cable from the OUT (TO TV) jack
on the back panel of the DVD-VCR to your television's Antenna
Input.
NOTE : Check the channel to connect DVD-VCR to your
television's Antenna Input; See page 22.
Line Connection
Connect an RCA-type audio/video cable (red, white, yellow) from
the LINE OUT jacks on the back panel of the DVD–VCR to your
television's Line In jacks. Use red for right audio, white for left
audio, and yellow for video.
NOTE: It is recommended that you use the Line Connection if your
TV is equipped with RCA jacks.
3 Plug In DVD-VCR
Connect the DVD-VCR power cord to a standard 120V/60Hz wall
outlet. Don't press any buttons on the DVD-VCR or remote during
auto setup. "AUTO" blinks while the DVD-VCR runs an auto setup
procedure, where it will automatically search for all active channels
and set the clock. When Auto setting has been completed, the front
panel displays the current time. If Auto Clock set is unable to find a
channel to set the clock, you can set the clock manually; See page
18.
4 Turn On DVD-VCR
Press the POWER button on the remote control or on the
DVD–VCR's front panel.
5 Turn On TV
Press the POWER button on your TV.
6 Set TV to Channel 3, 4 or Line
Be sure to use the same channel you selected in Step 2. If you
used the Line Connection, set your TV to its Line Input.
DVD & VCR
1
From Antenna or Cable
DVD & VCR
2
2
To TV's Antenna Input
3
POWER
4
2
POWER
SCREEN FIT
SHUTTLE
4 4 5
M O D E /
REPEAT
7 8
ZOOM
3D SOUND CL
13