DVD-VCR and to protect it from overheating. These openings must not be blocked or covered. Never place your VCR on a bed, sofa, rug or other similar surface, on or near a radiator or heat register. This DVD-VCR should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
• Watch a DVD while recording a TV show to the VCR. • Auto Setup automatically sets clock and searches for channels. • A/V switching between TV, VCR and DVD deck with TV view button for ease of use. • Remote controls both DVD and VCR decks.
SET TIMER (p.59) A Timer Recording is programmed or in progress. If blinking there is an error. Also displays without the clock hands to indicate that a recording is in progress, and blinks when the VCR is in Pause mode.
23-24. • Auto Clock Set — Sets the DVD-VCR’s internal clock. If Auto Clock Set is unable to find a channel to set the clock, you can set the clock manually; see page 18. This procedure may take a few minutes to complete. When finished, the DVD-VCR will tune to the lowest channel found.
DISC MENU • Many discs will begin playback automatically when the disc drawer closes. • If the DVD has a disc menu, or more than one title, the disc menu may appear. Additional DVD Options • For advanced DVD Setup options, see pages 27~37.
Press to display the channel you are watching. • Also works in DVD and VCR mode. On-Screen Menu Navigation The on-screen menu system allows you to set all functions for your DVD-VCR. The following buttons are used to open and navigate through the on-screen menu system.
01547A DVD-V1000/XAA-Eng2 5/16/02 3:38 PM Manual Clock Set If Auto Setup was unable to find a local TV station to set the DVD- VCR’s internal clock, follow these instructions to set the date/time manually. NOTE: It is important to set the clock for accurate Timer Recording.
• Ch## - Sets the DVD-VCR to search for a specific station. Use the 0-9 buttons to set the channel. • Line 1 - Searches for the time from a device connected to the front Line 1 inputs. • Line 2 - Searches for the time from a device connected to the rear Line 2 inputs.
Antenna or Cable, whichever you connected to the Antenna In DISC MENU jack during initial setup. • Use this setting only if Auto Setup detected the incorrect tuner band, i.e. channels are coming in on the wrong channel numbers. SETUP /ENTER Open “SETUP MENU”...
Move the selection arrow to “Channel Setup,” then push right to select. Select Channel to Add/Remove Use the 0–9 buttons to tune in the channel number you wish to add or remove. Select “Add/Remove Channel” Move the selection arrow to “Add/Remove Channel,” then push right to add/remove the channel from your channel list.
Tuner Audio to Mono, Stereo, SAP, or TV+SAP. Display Tuner Audio Status Press the AUDIO button while the TV View is set to the Tuner (i.e., when you are watching TV). • The current Tuner Audio status will appear in the upper right corner of the screen.
(odd and even scan lines), there are two ways to freeze an image during DVD playback: • Frame - Freezes both the odd and even scan lines that make up a single frame. Excellent for graphic detail, but may cause jitter in high motion scenes.
Move the selection arrow to “Language/Audio Setup,” then push right to select. Select “Disc Menu” Move the selection arrow to “Disc Menu,” then push right to select. Set “Disc Menu Language” Preference Move the selection arrow to your preferred language for DVD disc menus, then push Enter to select.
DVDs based on their content. The system uses an eight level rating system. • If you try to play a DVD that exceeds the selected rating, an error message will appear. • Not all discs are rated.
Digital Decoder. Use the Digital Audio Out connection below. Digital Audio Out Connect EITHER an optical cable OR a digital coaxial cable from the Digital Audio Out jacks on the back panel of the DVD-VCR to their corresponding Digital Audio Input jacks on your A/V Receiver: • Optical •...
Move the selection arrow to “Dolby D Decoder,” then push right to select from the following options: • Yes – Indicates that your A/V receiver is equipped with a Dolby Digital decoder. • No - Indicates that your A/V receiver is NOT equipped with a Dolby Digital decoder.
/ENTER • Each press increases or decreases the speed from normal playback to 2X - 4X - 8X - 16X - 32X - 128X. Press Play to resume normal speed. • Front Panel Search Buttons - Press and hold the Forward/Back buttons on the front panel to visually search forward/backward at 2x - 4X - 8X - 16X - 32X - 128X speed.
Use the " on the screen you want to zoom. Zoom In Press the ENTER button repeatedly to zoom in at 2X - 4X - 2X - and normal magnification. Angle Some DVDs allow you to view the same scene from different perspectives, or angles, while watching a movie.
In Play mode, press the REPEAT button, then push left/right to select A-B Repeat. • “A-” will blink when A-B Repeat is selected. NOTE: If you are playing a CD, the menu will display “Track” in place of “Chapter” Mark the Starting Point Press the ENTER button at the beginning of the segment you want to repeat (Point A).
• Languages are represented by abbreviations; i.e. “ESP” for “español.” Page 44 Bookmarks You can insert up to three Bookmarks on your DVDs, so you can jump quickly to your favorite scene or song. Open Bookmark Menu During playback, press the MARK button on the remote control.
Push the up/down to select the folder on the CD-R which contains the MP3 files you want to hear, then press Enter to select. • If there are more than 8 folders on the disc, push the left/right to view additional folders.
ANGLE Set 3D Sound INPUT PREV.CH Push the up/down to set “3D Sound” On or Off, then push the 3D SOUND button to confirm your selection. Page 48 Special VCR Playback Features While a videotape is playing, you can enjoy a variety of special playback features, including Still, Frame Advance, Skip, Repeat, and more.
ZOOM DISPLAY SHUTTLE MUTE CLOCK/ Adjust Tracking Manually MODE COUNTER During playback, press the TRK- or TRK + buttons to move the REPEAT white lines out of the picture. SKIP CLEAR 3D SOUND A.DUB TV/VCR F.ADV...
Before You Begin... • Power on the DVD-VCR • Power on the TV • Set the TV to channel 3 or 4 (whichever the switch is set to TV VIEW ANGLE on the back of the DVD-VCR).
0:11:40 Page 54 Record Speed You can slow down the recording speed from SP to SLP in order to fit six hours of programming on a T-120 tape. Start Recording Follow the Basic Recording instructions on page 52. Set Record Speed...
Copy the DVD to VHS Tape Press the COPY button on the DVD-VCR front panel. • The DVD will go into Play mode and the VCR will go into Record mode. • If the DVD disc menu appears, you may need to press the Play button manually to begin copying.
The Timer Recording Feature allows you to program up to 16 events at a time to record up to a year in advance. Set the TV to channel 3 or 4 (whichever the switch is set to on the back of the DVD-VCR).
Timer event begins to record in SP; the DVD-VCR then calculates how much time is remaining on the tape and adjusts the record speed to SLP if necessary to fit the entire event. If there is not enough tape to record the entire event, the DVD-VCR will record in SLP until the end of the tape is reached.
Shows you the current counter position in the DVD or VCR deck in hours, minutes, and seconds. Time Remaining (VHS only) Shows you the amount of time left on the tape in the VCR deck, computed by subtracting the current tape position from the total tape length in hours and minutes.
Index Search Index Search will fast-forward or rewind a specified number of Index Marks from 1 to 99. When it reaches the desired Index Mark, it will play the tape. Use Index Search when you know the exact Index Mark you want to locate.
DVD-VCR to the S-Video Input on your television. Connect Component Video Out to TV Connect a component video cable from the Component Video Out (Y, Pb Pr) on the back panel of the DVD-VCR to the Component Video Input on your television. Connect Audio Out...
Move the selection arrow to “Alt Video Out,” then push right to select from the following options: • Off - Indicates that you are using the standard RF or Line Out jacks to connect your DVD-VCR to your TV or display device.
TV screen. Then press Record on the VCR deck. Timer Record From Device Select Line 1 or Line 2 as your record source in the Timer Record menu. All other Timer Record settings should be set in the usual manner; see page 59.
NEWSAN Result: If your television is compatible with the remote control, it TV VIEW ANGLE will switch off. It is now programmed to operate with the INPUT PREV.CH remote control. If several codes are indicated for your television brand, try each one in turn until you find one that works.
Page 38
@ ? @ ? g @ Th s m ed wa an y beg ns on he o g na da e o pu chase and s va d on y on @ ? @ ? @ ? @ ? @ ? @...
Page 39
01547A DVD-V1000/XAA-Eng5 5/16/02 3:47 PM Page 76 SAMSUNG ELECTRONICS AMERICA, INC. HEADQUARTERS 105 Challenger Road, Ridgefield Park, N.J. 07660-0511 TEL: 1-800-SAMSUNG SERVICE DIVISION 400 Valley Road, Suite 201, Mount Arlington, NJ 07856 1-800-SAMSUNG (1-800-726-7864) ELECTRONICS AC68-01547A...