Advertisement
5. Take one of these actions.
IF YOU SELECTED...
A specific hour,
Sunrise or Sunset,
6. Press DATE/TIME/NEXT. The minute digit flashes.
7. Press + or - to set the minute for the event.
8. Press SET ON/OFF EVENTS to set the OFF Event. Dashed
lines appear to indicate no event is set for the event number.
9. Press DATE/TIME/NEXT. The screen displays 12:00 AM 1
OFF (OFF Event 1).
10. Press + or - to scroll to the days of the week that the program will run.
11. Press DATE/TIME/NEXT. The hour flashes.
12. Press + or - to scroll to the desired hour or AM Sunrise or PM
Sunset for the event.
13. Take one of these actions.
IF YOU SELECTED...
A specific hour,
Sunrise or Sunset,
14. Press DATE/TIME/NEXT. The minute digit flashes.
15. Press + or - to set the minute for the event.
16. If you want to set another ON/OFF pair, repeat steps 1 to 16.
17. If you are finished setting events, press and hold SET ON/OFF
EVENTS until the time of day screen appears.
NOTE: If you leave the timer idle in Calendar or Event setting
modes for 5 minutes, the timer will automatically switch to AUTO
operating mode after saving your settings.
Daily Operation
Once the initial settings are completed, follow this procedure
to select the operation mode in the timer.
TABLE 1. Description of Modes
Mode
AUTO
Switches ON/OFF events at programmed times.
RDM
Varies each event up to 30 minutes from the
(Random)
programmed time
MANUAL
Programmed events are ignored but are saved in
memory.
1. Press SELECT FUNCTION to scroll to the desired operation
mode. See Table 2 for selection of modes.
NOTE: In order for the time switch to run the programmed
events, the operation mode must be set to AUTO or RDM.
TABLE 2. Selecting Operating Mode.
Mode
ON
Load is ON permanently in MANUAL mode.
ON AUTO
AUTO has been selected, load is ON, and will
stay ON until the next scheduled OFF event.
ON RDM
RDM mode has been selected, load is ON,
and will stay ON until the next scheduled
RDM OFF event
OFF
Load is OFF permanently in MANUAL mode
OFF AUTO
AUTO mode is selected, load is OFF, and will
stay OFF until the next scheduled ON event.
OFF RDM
RDM mode has been selected, load is OFF,
and will stay OFF until the next scheduled
RDM ON event.
Reviewing or Modifying an Event
Follow this procedure to modify an event.
1. Press SET ON/OFF EVENTS to scroll to the desired event.
2. Press DATE/TIME/NEXT to select the event setting that
you want to modify.
3. Press + or - to adjust the setting, then press DATE/TIME/
NEXT to save and advance to the next setting.
4. Repeat step 3 as needed for this event.
5. If you want to modify another event, press SET ON/OFF
EVENTS to scroll to the desired event.
THEN...
Go to step 6.
Press SET ON/OFF EVENTS
to advance to setting OFF
time for event and go to step 8.
THEN...
Go to step 14
Go to step 16
Description
Description
6. When the modifications are complete, press SET ON/OFF
EVENTS to scroll through all 7 ON/OFF events (including blank
events) and return to the time of day screen (flashing colon).
Deleting an Event
Follow this procedure to delete an event.
1. Press SET ON/OFF EVENTS to scroll to the unwanted ON
or OFF event.
2. Press DELETE. The screen displays dashes to indicate the
ON or OFF event is deleted.
NOTE: If necessary, repeat this procedure to delete both
ON and OFF settings for the event.
3. When the modifications are complete, press SET ON/OFF
EVENTS to scroll through all 7 ON/OFF events (including blank
events) and return to the time of day screen (flashing colon).
Resetting the Timer
In case of a time malfunction or to delete all previous settings, the
unit can be reset.
To reset the timer, use a pen or blunt object to Press RESET. The
timer resets and deletes all the settings in the unit
Replacing the Battery
One AA size alkaline battery is needed to complete this procedure.
1. Unplug the timer power cord.
2. From the rear of the timer, remove the retaining screw and
battery cover.
3. Install the new AA battery (observe polarity).
4. Verify that the controller display activates.
5. Take one of these actions.
IF THE DISPLAY...
THEN...
Activates
Go to step 6.
Does not activate,
Make sure the battery is not dead and
is installed with the proper polarity.
Adjust as needed to get the screen to
activate.
6. Replace the battery cover and retaining screw.
7. Go to Setting the Calendar, Clock and Astronomic Time.
NOTE: If the timer is going to be stored for an extended
period of time, it is recommended to remove the battery to
preserve the life of the battery
Troubleshooting
Symptom
The timer is losing settings
Low battery not holding memory
Output does not switch or output switches
Auto or RDM mode is not properly selected. Select the desired mode. See Daily
at wrong time
There are extra or incorrect event settings. Press SET ON/OFF EVENTS to scroll
Astro Events have seasonally adjusted
beyond fixed time.
LIMITED ONE YEAR WARRANTY
If within the warranty period specified, this product fails due to a defect in material or workmanship,
Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended
to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to
units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units
which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not
used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps
and/or lamp bulbs, LED's and batteries; (f) the finish on any portion of the product, such as surface and/
or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs,
removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL
IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST
ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS
THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE
DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was
purchased, or (b) completing a warranty claim on line at www.intermatic.com. This warranty is made by:
Intermatic Incorporated, Customer Service 7777 Winn Rd. Spring Grove, Illinois 60081-9698. For
warranty service go to: http://www.intermatic.com or call 815-675-7000.
INTERMATIC INCORPORATED,
.
.
Possible Cause
Solution
Replace the battery. See Replacing the
Battery.
Operation.
through the events to find the event that
needs to be changed or deleted.
See Reviewing or Modifying an Event.
Make sure the fixed timed events are not set
anywhere in the range of earliest to latest
sunrise and sunset.
SPRING GROVE, ILLINOIS 60081-9698
158--01635
Advertisement
