Page 2
Safety Instructions Introduction Package Contents Your LCD Display Machanical Layout Connections The color and appearance of the product may vary depending on the model, and the product specifications are Using the Software subject to change without prior notice for reasons of performance enhancement. Adjusting the LCD Display Troubleshooting Introduction...
Page 3
Batteries (AAA X 2) Remote Control (Not available in all locations) BNC to RCA Adaptor Jack USB Holder & Screw (1EA) Sold separately Wall Mount KIT Speaker Set BNC Cable LAN Cable Front Cover-Hole Semi Stand Screw: 4 EA HDD Cover DVI Cable Your LCD Display...
Page 4
MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons)/ Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume.
Page 5
Rear Note • For detailed information concerning cable connections, refer to Connecting Cables under Setup. The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. POWER S/W ON [ | ] / OFF [O] Switches the LCD Display On/Off.
Page 6
Note • The number of LCD Displays that can be connected to loopout may differ depending on the cables, signal source etc. With cables where there is no degradation or signal source, up to ten LCD Displays can be connected. COMPONENT AUDIO IN [L-AUDIO-R] (Component Audio Connection Terminal (Input))
Page 7
Note • See Connecting the LCD Display for further information regarding cable connections. Remote Control Note • The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. ON / OFF Turns the LCD Display On/Off.
Page 8
For example, to select channel 121, press "+100", then press "2" and "1". - This fuction does not work for this monitor. Adjusts the audio volume. MUTE Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode.
Page 10
Note • Only the supplied bolts should be used. Caution Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Installing the Semi Stand To protect your product, a Cover Hole is included as an accessory. This protects the hole at the bottom of the monitor where the stand is inserted.
Using a Power cord with Earth In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance.
• Turn on both your computer and the LCD Display. Note • The DVI cable or BNC cable is optional. Contact a local Samsung Electronics Service Center Connecting a VCR AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [S-VIDEO] of the LCD Display using an S-VHS or BNC cable.
Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the DVD player. Connect a Component cable between the BNC/COMPONENT IN - P and the P , Y, P jacks on the DVD player.
• The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. Connecting a DTV Set Top Box Note •...
Page 15
Note • Connect the speaker connection cable between the speaker connection jack on the back of the SET and the speaker connection jack on the back of the speaker. Note • Do not move the SET while the SET is connected to the speakers. The speaker-bracket for connecting the SET speaker my become damaged.
Note • You can control your monitor by allowing it to receive the remote control signals of other devices through the REMOTE OUT terminal. • You can control a device by allowing it to receive remote control signals from other devices through the REMOTE IN terminal.
Connect the LAN cable. Connecting a USB device You can connect USB devices such as a mouse or keyboard. Using a USB Holder When using a small external device such as a portable memory stick and it is connected to the USB terminal at the back of your monitor, it is exposed to the possiblity of theft or loss.
Page 18
Insert part of your USB holder into the groove in part Align part of your USB holder with the groove at the bottom of part Align part of your USB holder with the bottom of part Insert a screw into the groove aligned in step [2], and fasten it. Align with and use a screw to fix them.
Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting The color and appearance of the product may vary depending on the model, and the product specifications are Self-Test Feature Check subject to change without prior notice for reasons of performance enhancement. Check List Q &...
Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend that a Samsung cleansing agent is used to prevent damage to the screen. Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly.
Page 22
The LCD Display screen flickers. Problems related to the Screen Note • Problems related to the LCD Display screen and their solutions are listed. Problems The screen is blank and the power indicator is off. "Check Signal Cable" message. "Not Optimum Mode " message. The picture rolls vertically.
Page 23
• Problems related to audio signals and their solutions are listed below. Problems No sound. The sound level is too low. The sound is too high or too low. Problems related to the Remote Control Note • Problems related to the remote control and their solutions are listed. Problems The remote control buttons do not respond.