Use M8 nuts and bolts. Nuts and bolts smaller than M8 could cause the setting plate to fall. Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation.
Page 3
Warning When you mount the projector on the wall with the setting plate, the wall requires enough strength to hold the projector and the setting plate. This setting plate should be installed on a concrete wall. Confirm the weight of the projector and the setting plate before installation, and maintain the strength of the wall.
• When using Keystone, the amount of V-Keystone and H-Keystone correction is no more than ±6. About This Installation Guide This guide describes how to mount the short-throw projector EB-485Wi/485W/480i/480/475Wi/475W/470 to a wall using the exclusive setting plate.
Page 5
Package Contents s p. 6 Specifications s p. 7 Connecting Devices s p. 9 Projection Distance Table s p. 10 Installation Procedure s p. 18 (1) Disassemble the parts (2) Assemble the parts (3) Install the wall plate on the wall (4) Determine the projection distance and pull out the slider (5) Route the cables through the setting plate (6) Attach the setting plate to the wall plate...
1. Package Contents Setting plate Wall plate 3-axis adjustment unit Slide plate * The slide plate is secured to the 3-axis adjustment unit when shipped. Wall plate cover End cap Hexagon wrench (for M4) Open-ended spanner 13 mm (for M8 and M6) x Template sheet 6 mm (for hexagonal axis) (for installing the wall plate)
2. Specifications Item Specification Remark Reference Page Setting plate mass (including the Approx. 7.4 kg Setting plate (2.8 kg), 3-axis adjustment unit (1.1 kg), 3-axis adjustment unit, slide plate, slide plate (0.7 kg), wall plate (2.5 kg), wall plate cover wall plate, wall plate cover, and and end cap (0.3 kg) end cap)
Horizontal slide adjustment range 45 mm 45 mm Forward/backward slide adjustment range Arm slide adjustment range 248 mm Adjustment from 3-axis adjustment unit installation position By changing the installation position of the 3-axis adjustment unit to the front or back, you can adjust the installation position of the projector.
Dedicated USB cable (supplied with document camera) When using the Easy Interactive Function (EB-485Wi/480i/475Wi only) When drawing by connecting to a computer, you need a USB cable. However, when drawing with the projector's built-in function, you do not need a USB cable.
4. Projection Distance Table Refer to the table below and install the setting plate and projector to project images at an appropriate size on the projection surface. The values are only rough estimates. The recommended range for the projection distance (a) is 62 to 311 mm. The numbers on the slider measure (b) are the same as the projection distance (a) when the screen size (S) is 70 inches or more.
The distance (c) from the projection screen to the wall plate is the number given when the vertical slide is set to the standard position. Match the notch on the setting plate to the position of the stamp on the wall plate. Standard position EB-485Wi/485W/475Wi/475W (4:3 aspect ratio) [Unit: cm] Screen Size Projection...
Page 12
100.6 TeamBoard RT TMWM5422CL/ 69" 140.3 x 105.2 14.9 - 30.7 21.1 - 36.9 18.3 105.2 The smallest screen size is 56". EB-485Wi/485W/475Wi/475W (16:10 aspect ratio) [Unit: cm] Screen Size Projection Numbers on Distance Height of Distance the slider Between...
Page 13
The value may differ depending on the location where you place the projector. When projecting in Tele, the quality of the projected images may decrease. When using EB-485Wi/485W/475Wi/475W to project images at a 4:3 aspect ratio, the images are resized automatically and the quality of the projected images may...
The distance (c) from the projection screen to the wall plate is the number given when the vertical slide is set to the standard position. Match the notch on the setting plate to the position of the stamp on the wall plate. Standard position EB-485Wi/485W/475Wi/475W (4:3 aspect ratio) [Unit: cm] Screen Size Projection...
Page 15
182.9 x 137.2 28.9 - 31.1 23.5 137.2 93" 189.1 x 141.7 30.9 - 31.1 24.2 141.7 The largest screen size is 93". EB-485Wi/485W/475Wi/475W (16:10 aspect ratio) [Unit: cm] Screen Size Projection Numbers on Distance Height of Distance the slider Between...
Page 16
88" 189.5 x 118.5 31.1 * 36.2 118.5 Hitachi Starboard FX DUO-88W The largest screen size is 88". * Figure for Wide (maximum zoom). EB-485Wi/485W/475Wi/475W (16:9 aspect ratio) [Unit: cm] Screen Size Projection Numbers on Distance Height of Distance the slider...
Page 17
The value may differ depending on the location where you place the projector. When projecting in Tele, the quality of the projected images may decrease. When using EB-485Wi/485W/475Wi/475W to project images at a 4:3 aspect ratio, the images are resized automatically and the quality of the projected images may...
Use M8 nuts and bolts. Nuts and bolts smaller than M8 could cause the setting plate to fall. ❏ Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation. Disassemble the parts Remove the slide plate from the 3-axis adjustment unit.
Page 19
(2) Attach the slide plate to the projector. Attach the slide plate to the projector using the M4 x 12 mm hexagon socket head cap bolts (x4) supplied. M4 x 12 mm hexagon socket head cap Slide plate bolts Spring washer Washer (3) Attach the 3-axis adjustment unit to the setting plate.
Install the wall plate on the wall (1) Determine the template sheet position. • From the projection distance table, confirm the screen size (S) and the distance between the projection surface and wall plate (c). • Align the Image Center line (vertical) of the template sheet with the center line (vertical) of the projection surface.
Page 21
(4) Drill holes of the following diameters and depths. Drill diameter 8.5 mm Pilot hole depth 40 mm Anchor hole depth 35mm (5) Remove the template sheet. (6) Use a device such as a dust pump to clean out concrete dust from the hole. (7) Position the wall plate on the wall and insert M8 x 50 mm expansion anchors into the holes.
Determine the projection distance and pull out the slider (1) In the projection distance table, check the number for the slider measure (b). (2) Loosen the M4 x 12 mm hexagon socket head cap bolts (x2), and then pull out the slider on the setting plate.
Attach the setting plate to the wall plate (1) Insert the hexagonal axis at the top of the setting plate into the wall plate ( (2) Insert the M8 hexagon bolt at the bottom of the setting plate into the wall plate ( Caution Take care not to trap the cables between the setting plate and wall plate.
Page 24
(3) Secure the setting plate to the wall plate by tightening the supplied M6 x 20 mm cross recessed head shoulder screws (x3) with the No.3 cross-head screwdriver ( M6 x 20 mm cross recessed head shoulder screws (x3) (4) Loosely tighten the M6 x 20 mm hexagon shoulder bolt supplied ( M6 x 20 mm hexagon shoulder bolt Spring washer Washer...
Page 25
Adjust the vertical slide to align it with the standard position (1) Adjust the vertical slide with the M8 hexagon bolt at the bottom of the setting plate, or the hexagonal axis at the top of the setting plate. Align with the standard position ( Tightening the M8 hexagon bolt lowers the setting plate, and loosening the bolt raises it.
Secure the projector to the setting plate (1) Loosen the two screws and remove the cable cover from the projector. Screws (x2) Cable cover (2) Insert the slide plate into the setting plate from the interface side of the projector ( Align the 3-axis adjustment unit with the slide plate's standard position ( (3) Tighten the M4 x 12 mm hexagon socket head cap bolts (x2) ( Slide plate...
Connect the power cord and other cables to the projector Connect any necessary cables such as the power cord, computer cable, and USB cable to the projector. Power cord Computer cable USB cable...
6. Adjusting the Projection Screen To ensure maximum projection screen quality, follow the steps below to adjust the projection screen. Do not make adjustments with the Keystone function of the projector. Doing so may result in a reduction in image quality. Turn on the projector Using the Remote Control Using the Control Panel...
Display the test pattern (1) Press the [Help] button. Using the Remote Control Using the Control Panel (2) Press the [ ] button on the remote control, or the [Wide] button on the control panel. The test pattern is displayed. Using the Remote Control Using the Control Panel Adjust the focus...
Page 30
Use the left adjustment dial to adjust the horizontal roll Repeat steps as necessary. (1) Loosen the screw in the following figure ( (2) Turn the adjustment dial ( ) to adjust the horizontal roll ( Screw (3) After you finish making all of the adjustments in steps , tighten the screw you loosened in...
Use the right adjustment dial to adjust the horizontal rotation (1) Loosen the screws (x2) in the following figure ( (2) Turn the adjustment dial ( ) to adjust the horizontal rotation ( Screws (x2) (3) After you finish making all of the adjustments in steps , tighten the screws (x2) you loosened in Use the top adjustment dial to adjust the vertical tilt...
Adjust the horizontal slide (1) Loosen the M4 x 12 mm hexagon socket head cap bolts (x2), and then adjust the slider for the slide plate. M4 x 12 mm hexagon socket head cap bolts (x2) (2) After you finish making all of the adjustments in steps , tighten the M4 x 12 mm hexagon socket head cap bolts (x2).
Adjust the vertical slide (1) Loosen the M6 x 20 mm hexagon shoulder bolt ( (2) Adjust the vertical slide with the M8 hexagon bolt at the bottom of the setting plate, or the hexagonal axis at the top of the setting plate ( Tightening the M8 hexagon bolt lowers the setting plate, and loosening the bolt raises it.
7. Attaching the Covers Attach the wall plate cover and end cap (1) Attach the wall plate cover ( Depending on how the cables are wired, you may need to cut out parts of the wall plate cover to allow the cables to be passed through it. When cutting the thin section of the wall plate cover and passing the cables through, make sure you perform deburring to smooth off any sharp edges to prevent damaging the cables.
Page 35
Caution Only a specialist should remove or reinstall the projector, including for maintenance and repairs. Refer to the User’s Guide of your projector for instructions on maintenance and repairs. Warning ❏ Never loosen the bolts and nuts after installation. Confirm that the screws have not become loose on a regular basis.
8. Appendix Using the Easy Interactive Function After you install an Easy Interactive Function compatible model (EB-485Wi/480i/475Wi), you need to perform calibration to align the positions of the cursor and Easy Interactive Pen. When using Easy Interactive Tools, you need to install Easy Interactive Tools Ver.2 on your computer. You also need to install Easy Interactive Driver Ver.2 when performing mouse operations or drawing on Mac OS X.