IBM 7331 Installation Manual
  1. Manuals
  2. Brands
  3. IBM Manuals
  4. Storage
  5. 7331
  6. Installation manual
IBM 7331 Installation Manual

IBM 7331 Installation Manual

8mm tape library
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IBM
7331 and 3449 8mm Tape Library
Model 3xx
Installation Guide
GA32-0375-00

Advertisement

Table of Contents
loading

Related Manuals for IBM 7331

Summary of Contents for IBM 7331

  • Page 1 7331 and 3449 8mm Tape Library Model 3xx Installation Guide GA32-0375-00...
  • Page 3 7331 and 3449 8mm Tape Library Model 3xx Installation Guide GA32-0375-00...
  • Page 4 IBM Corporation, Department 61C, 9000 South Rita Road, Tucson, AZ 85744-0001, U.S.A. When you send information to IBM, you grant IBM a nonexclusive right to use or distribute the information in any way it believes appropriate without incurring any obligation to you.

  • Page 5: Table Of Contents

    ......... . . Copyright IBM Corp. 1997...
  • Page 6 7331 and 3449 Installation Guide...
  • Page 7 ......Power Receptacle Index ......Copyright IBM Corp. 1997...
  • Page 8 7331 and 3449 Installation Guide...

  • Page 9: Notices

    IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM program or other IBM product in this publication is not intended to state or imply that only IBM’s program or other product may be used.
  • Page 10 If the automatic lock on the front door is not functioning and the door is open, do not look directly at the laser beam. Staring at the beam may cause damage to your eyes. (RSFTC239) viii 7331 and 3449 Installation Guide...

  • Page 11: Ac Grounding Diagram (50 Hz And 60 Hz)

    Attention Notices An attention notice indicates the possibility of damage to a program, device, system, or data. Safety Inspection Procedures Perform the following safety inspection prior to the normal maintenance agreement inspection. Suspect the 8mm Tape Library is unsafe until verified it is safe. If unsafe conditions are present, decide how serious the hazard is and whether you can continue without correcting the problem.
  • Page 12 Environmental Design The environmental efforts that have gone into the design of this unit signifies IBM’s commitment to improve the quality of its products and processes. Some of these activities include elimination of the use of CFCs, development of reusable or recyclable packaging, and reductions in manufacturing wastes.
  • Page 13 (“IBM”) owns copyrights in Code or has the right to license Code. IBM or a third party owns all copies of Code, including all copies made from them. If you are the rightful possessor of a Specific Machine, IBM grants you a license to use the Code (or any replacement IBM provides) on, or in conjunction with, only the Specific Machine for which the Code is provided.
  • Page 14 Electronic Emission Notices The following statement applies to this IBM product. The statement for other IBM products intended for use with this product will appear in their accompanying manuals. Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 15 TV communications and to other electrical or electronic equipment. Such cables and connectors are available from IBM authorized dealers. IBM cannot accept responsibility for an interference caused by using other than recommended cables and connectors. Germany Only: This product is in conformity with the EN55022 class B emission limits.
  • Page 16 7331 and 3449 Installation Guide...

  • Page 17: Preface

    Appendix A, “Power Cables” on page 29 provides information on power cables and their proper use. Appendix B, “Statement of Limited Warranty” on page 33 is the 7331 and 3449 8mm Tape Library Model 3xx: Installation Guide warranty. “Glossary” on page 37 defines terms, abbreviations, and acronyms used in this publication.
  • Page 18 7331 and 3449 Installation Guide...

  • Page 19: Chapter 1. General Information

    Chapter 1. General Information This chapter provides a brief description of the 7331 and 3449 8mm Tape Libraries and their configuration options. The options consist of 7331 Model 305, which is used in a RISC System 6000 environment; 3449 Model 355, used in a PC Tower environment, and;...

  • Page 20: 8Mm Tape Library Scsi Bus Configurations

    The 8mm Tape Library provides fast wide differential Small Computer System Interface (SCSI-2), which attaches to the RISC System/6000 (RS/6000) computer, and IBM PC Company PC Servers. 8mm Tape Library SCSI Bus Configurations The 8mm Tape Library can be set in the following SCSI BUS configurations:...

  • Page 21: 8Mm Tape Library Configurations

    Sequential Mode (Selectable) Random/Sequential (Available only in Split configuration) Sequential/Random (Available only in Split configuration) See the 7331 and 3449 8mm Tape Library Model 3xx Operator Guide, for a more detailed description of all the modes. Chapter 1. General Information...
  • Page 22 7331 and 3449 Installation Guide...

  • Page 23: Chapter 2. 8Mm Tape Library Installation

    Chapter 2. 8mm Tape Library Installation This chapter provides step-by-step instructions on how to properly install the 7331 and 3449 Tape Library Model 3xx. You should complete the following steps when installing the 8mm Tape Library. Step 1. Checking the Electrical Outlets...

  • Page 24: Step 3. Inventory Checklist

    Make sure you have received the following items: Power cables for 7331 Model 305 and 3449 Model 355 1 , and 3449 Model 356 2 power cables are represented in Figure 4 and detailed in Appendix A, Power Cables.

  • Page 25: Step 4. Unpacking The 8Mm Tape Library

    After completing the installation of the library, store this guide, the 7331 and 3449 8mm Tape Library Model 3xx Operator Guide, the 7331 and 3449 8mm Tape Library Model 3xx Service Guide, and External Devices Translated Safety Notices with your host computer system documentation near the 8mm Tape Library.

  • Page 26: Step 5. Host System Unit Setup For Connection To The 8Mm Tape Library

    Install the SCSI card in the system unit. See the system unit documentation for installation of card. Power on the system unit. Go to “Step 7. Placing the 8mm Tape Library” on page 16. 7331 and 3449 Installation Guide...

  • Page 27: Step 6. Installing The Rack Hardware And The Rack-Mounted 8Mm Tape Library Model 356

    Step 6. Installing the Rack Hardware and the Rack-Mounted 8mm Tape Library Model 356 Use the following procedure to install the Rack Hardware and the Rack-Mounted Model 356. Step 1. If required, vary off the rack devices where the library will be installed. Step 2.

  • Page 28: Base Plate Installation

    6. Place base plate 2 on rails 1 and 3 on rack. Position plate with large holes to front and left. Do not fasten plate to rails at this time. See Figure 7. Figure 7. Base Plate Installation 7331 and 3449 Installation Guide...

  • Page 29: Filler Strip And Bezel Strip Assembly

    Step 7. Assemble the frame that surrounds the library front door and holds the filler plate. Step a. Arrange the 2 filler strips 1 and 4 , and 2 bezel strips 2 and 5 , and fasten together with 2 screws 3 (typical 2 screws each corner) at each corner.

  • Page 30: Filler Strip And Bezel Strip Installation

    If possible, disconnect all power cords from the existing system before you add or remove a device. 7331 and 3449 Installation Guide...

  • Page 31: Ground Straps (Frame To Door)

    Step 16. On the inside of the front door, remove the screw securing each frame-to-door ground strap. There are two ground straps 1 . See Figure 10. Figure 10. Ground Straps (Frame to Door) Step 17. Grasp the front door assembly 4 and lift it off the hinges. Place the front door assembly where it will not get damaged.

  • Page 32: Library Front Frame Alignment

    Step 24. Using 2 screws, fasten the filler plate to the library. See Figure 13. Step 25. Obtain the front door assembly and align the hinge pins with the library hinges and lower the door assembly into position. 7331 and 3449 Installation Guide...
  • Page 33 Step 26. Connect each frame-to-door ground strap to the inside of the front door. See Figure 10 on page 13. Step 27. Connect the control panel signal cable to the control panel. Step 28. Install a cable tie to secure the control panel cable to the safety cover. Note: The door does not lock in step 29.

  • Page 34: Step 7. Placing The 8Mm Tape Library

    (RSFTD204) DANGER To prevent a possible electrical shock from touching two surfaces with different electrical grounds, use one hand, when possible, to connect or disconnect signal cables. (RSFTD004) 7331 and 3449 Installation Guide...

  • Page 35: Step 9. Single Drive - Single Host Scsi Configuration

    Step 9. Single Drive – Single Host SCSI Configuration System Unit System Adapter System-to-Device SCSI Cable Tape Library Backpanel SCSI Jumper Term inator RSCSI01-00 Figure 14. Single Drive-Single Host SCSI Configuration Refer to Figure 14 and perform the following steps: Step 1.

  • Page 36: Step 10. Dual Drive - Single Host Scsi Configuration

    7. Go to “Step 12. Connecting the Power Cables” on page 20. The advantages of this configuration include: Two jobs can be run simultaneously. Library functions available for both drives (for Random Mode only). The disadvantage of this configuration is the loss of drive performance. 7331 and 3449 Installation Guide...

  • Page 37: Step 11. Dual Drive - Dual Host Scsi Configuration

    Step 11. Dual Drive – Dual Host SCSI Configuration System Unit System Adapter System-to-Device SCSI Cable Tape Library Backpanel System Unit System Adapter Term inator RSCSI03-00 Figure 16. Dual Drive-Dual Host SCSI Configuration Refer to Figure 16 and perform the following steps: Step 1.

  • Page 38: Step 12. Connecting The Power Cables

    01E5 (drive presence) error. Step 3. Open the control panel access cover and press power switch ( ) to turn the library power On. Display Panel Power Switch Power-On Indicator ASOP03-00 Figure 17. Control Panel 7331 and 3449 Installation Guide...

  • Page 39: Power On Selftest In Progress Display

    The library may also beep and blink (power-on indicator) one of four sequences to indicate a specific error. These errors are defined in the 7331 and 3449 8mm Tape Library Model 3xx Service Guide. Step 7.

  • Page 40: Power On Selftest Failure Display

    Figure 20: Power On Selftest Warning and other information to further identify the cause of the error. The message is displayed for 3 seconds before the library resumes operation. Figure 20. Power On Selftest Warning Display 7331 and 3449 Installation Guide...

  • Page 41: Power On Selftest Complete Display

    Step 14. Make sure the library covers are installed. Step 15. If additional language support is required, refer to the 7331 and 3449 8mm Tape Library Model 3xx Operator Guide, GA32-0376, for instructions on how to select the required language.
  • Page 42 7331 and 3449 Installation Guide...

  • Page 43: Chapter 3. Moving The 8Mm Tape Library

    Step 2. Remove any tape cartridges loaded in the tape drives. Step 3. Power-off the library. Refer to the 7331 and 3449 8mm Tape Library Model 3xx Operator Guide, GA32-0376, for instructions on powering off the library. Copyright IBM Corp. 1997...

  • Page 44: Picker Transport Lock

    5. If the library is being moved a short distance (for example, across the room), do the following: a. Position the picker at the top of the library and lock in place with the accessor lock (mechanical). See Figure 24. Accessor Lock ASACCLK-00 Figure 24. Accessor Lock 7331 and 3449 Installation Guide...
  • Page 45 DANGER To prevent a possible electrical shock when installing the device, ensure that the power cord for that device is unplugged before installing signal cables. (RSFTD204) DANGER To prevent a possible electrical shock from touching two surfaces with different electrical grounds, use one hand, when possible, to connect or disconnect signal cables.
  • Page 46 See Figure 24 on page 26. Step e. Power-on the library. Refer to the 7331 8mm Tape Library Model 3xx Operator Guide, GA32-0376, for instructions on powering on the library. 7331 and 3449 Installation Guide...

  • Page 47: Appendix A. Power Cables

    Figure 25 lists the power cable part number, the country where the power cable can be used, and an index number to be matched with the receptacle illustrations shown in Figure 26 on page 31. Please contact your local dealer if your 7331 Tape Library power cable does not match this information.

  • Page 48: Power Cable Information

    Kuwait, Malawi, Malaysia, Nigeria, Oman, People's Republic Kingdom of China, Qatar, Sierra Leone, Singapore, Tanzania, Uganda, United Arab Emirates (Dubai), United Kingdom, Zambia 14F0051 Liechtenstein, Switzerland Switzerland 14F0069 Chile, Ethiopia, Italy Italy 14F0087 Israel Israel 6952291 Colombia, Paraguay, Uruguay Colombia 7331 and 3449 Installation Guide...

  • Page 49: Model 355 Power Cables

    Figure 26. Power Receptacle Index Model 355 Power Cables Model 355 cables are the same as for Model 305. Model 356 Power Cables The power cables for Model 356 are PN 13F9961 and PN 34G0253. Appendix A. Power Cables...
  • Page 50 7331 and 3449 Installation Guide...

  • Page 51: Appendix B. Statement Of Limited Warranty

    The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you originally purchase for your use, and not for resale, from IBM or your reseller. The term “Machine” means an IBM machine, its features, conversions, upgrades, elements, or accessories, or any combination of them.
  • Page 52 IBM or your reseller of changes in a Machine's location. IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM’s possession or 2) in transit in those cases where IBM is responsible for the transportation charges.
  • Page 53 Limitation of Liability Circumstances may arise where, because of a default on IBM’s part or other liability you are entitled to recover damages from IBM. In each such instance, regardless of the basis on which you are entitled to claim damages from IBM (including...
  • Page 54 7331 and 3449 Installation Guide...

  • Page 55: Glossary

    Glossary SCSI. Small computer system interface: cabling used RS/6000. IBM RISC System/6000: a reduced to interface one device to another or other devices. instruction set computer. PC. Personal Computer: an individual workstation comprised of 'desk-top-type' hardware including a monitor. Copyright IBM Corp. 1997...
  • Page 56 7331 and 3449 Installation Guide...

  • Page 57: Index

    9 rack mount model 356 9 rack mount model 356, checklist 6 SCSI 16 single drive, single host 17 library modes 3 limited warranty 33 model 356 checklist 6 installation 9 move tape library 25 Copyright IBM Corp. 1997...
  • Page 59 Please tell us how we can improve this book: Thank you for your responses. May we contact you? When you send comments to IBM, you grant IBM a nonexclusive right to use or distribute your comments in any way it believes appropriate without incurring any obligation to you.
  • Page 60 Cut or Fold Readers' Comments — We'd Like to Hear from You Along Line GA32-0375-00 Fold and Tape Please do not staple Fold and Tape PLACE POSTAGE STAMP HERE International Business Machine Corporation Department 61C 9000 South Rita Road Tucson, AZ 85741-0001 U.S.A. Fold and Tape Please do not staple Fold and Tape...
  • Page 61 Index...
  • Page 62 Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber. GA32- 375-...

This manual is also suitable for:

3449

Table of Contents