Bosch GSR 6-45 TE Professional Original Instructions Manual page 12

OBJ_BUCH-137-009.book Page 12 Tuesday, February 23, 2016 10:17 AM
12 | English
Noise/Vibration Information
Sound emission values determined according to EN 60745-2-1.
Typically the A-weighted noise levels of the product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined
h
according to EN 60745:
Screwdriving without impact:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 60745-1, EN 60745-2-1, EN 60745-2-2, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
1 609 92A 2BN | (23.2.16)
3 601 ... D45 0..
dB(A)
dB(A)
dB(A)
2
m/s <2.5
2
m/s
Assembly
Changing the Tool (see figure A)
 Before any work on the machine itself, pull the mains
plug.
Pull off the screwing-depth stop 4 toward the front. Pull out
the screwdriver bit 1. If required, the universal bit holder 10
can also be pulled off and replaced.
After changing the tool, reattach the screwing-depth stop 4.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
To save energy, only switch the power tool on when using it.
Reversing the rotational direction
The rotational direction switch 8 is used to reverse the rota-
tional direction of the machine. However, this is not possible
with the On/Off switch 7 actuated.
Right rotation: For driving in screws, push the rotational di-
rection switch 8 left to the stop.
Left rotation: Push the rotational direction switch 8 right to
the stop (for unscrewing screws).
Switching On and Off
To start the machine, press the On/Off switch 7 and keep it
pressed.
To lock the pressed On/Off switch 7, press the lock-on button
6.
To switch off the machine, release the On/Off switch 7 or
when it is locked with the lock-on button 6, briefly press the
On/Off switch 7 and then release it.
Adjusting the Speed
The speed of the switched-on power tool can be variably ad-
justed, depending on how far the On/Off switch 7 is pressed.
Light pressure on the On/Off switch 7 results in a low rotation-
al speed. Further pressure on the switch results in an increase
in speed.
D45 1.. D45 2..
81 79 81
92 90 92
3 3 3
<2.5 3.3
1.5 1.5 1.5
Bosch Power Tools