JVC KV-DV50 Installation And Connection Manual

KV-DV50
Installation/Connection Manual
GET0482-009A
[A]
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
• Avoid installing the unit in the following places.
– Where it would hinder your safety driving.
– Where it would be exposed to direct sunlight or heat directly from the heater or placed in an
extremely hot place.
– Where it would be subject to rain, water splashes or excessive humidity.
– Where it would be subject to dust.
– Where it would be positioned on an unstable place.
– Where it could damage the car's fittings.
– Where proper ventilation would not be maintained, such as under a floor mat.
– Where it would be located near inflammable objects (since heat is generated inside the unit).
• DO NOT operate the unit while driving.
• If you need to operate the unit while driving, be sure to look around carefully.
• The driver must not watch the monitor while driving.
If the parking brake is not engaged, "DRIVER MUST NOT WATCH THE MONITOR WHILE
DRIVING." appears on the monitor, and no playback picture will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake
system built into the car.
To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car's chassis again after installation.
Parts list for installation and connection
If any item is missing, consult your JVC car audio dealer immediately.
A
Main unit
D
Power cord (4-pins)
G
Flat countersunk screw
×
(M5 8 mm)
J
Remote sensor unit

TROUBLESHOOTING

• The fuse blows.
* When connecting through the car battery directly: Are the red and black leads connected correctly?
* When connecting through the cigarette lighter socket: Is the fuse with an appropriate rating (5 A) is
used?
• Power cannot be turned on.
* When connecting through the car battery directly: Is the yellow lead connected?
* When connecting through the cigarette lighter socket: Is the cigarette lighter plug connected correctly?
• Picture does not appear on the monitor.
* Is the video cord connected correctly?
• Sound cannot be heard.
* Is the audio cord connected correctly?
• This unit does not work at all.
* Have you reset your unit?
B C
Installation sleeve Audio/video cable (3 m)
E F
L-shaped bracket Tapping screw
×
(M5 20 mm)
H I
Binding screw Double-sided tape
×
(M5 8 mm)
K L
Remote controller Battery
INSTALLATION
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
When installing on the floor
With this arrow
facing the front
When installing in the dashboard
1
Remove the audio system originally installed together with the mounting brackets.
Note: Be sure to keep all the screws and parts removed from your car for future use.
2
Attach the mounting brackets (removed from the car), to this unit (see below).
3
Connect the wires (see diagram ).
4
Fix this unit to the car using the screws removed in step 1.
• See "Caution" below.
Car audio, etc.
Screw removed from
the car in step 1
Screws supplied for this unit:
Select the proper screw type, appropriate for your car.
×
Binding screws (M5 8 mm)
If there is an interfering tab on the mounting
bracket, bend it flat.
Caution:
• To install the mounting brackets onto the unit, use only the supplied screws (M5 × 8 mm). If you
use any screw longer than 8 mm, the unit may be damaged.
• Never use the bolts or nuts from the vehicle's safety devices for installation. If the bolts or nuts
from the steering wheel, brakes or other safety devices are used for installation, it may cause an
accident.
1
0507DTSMDTJEIN
EN
© 2007 Victor Company of Japan, Limited
Be careful not to damage the wiring
or parts under the floor.
Screw removed from
the car in step 1
Mounting bracket
removed from the car
KV-DV50
Screw removed from the car in step 1
×
Flat countersunk screws (M5 8 mm)
Install the unit at an angle of less than 30°.