To Copy The System Settings From The First To The Second User Interface - Daikin Altherma EBLQ014CAV3 Installation Manual

5 Configuration
4 If you do NOT press any button for more than 1 hour or press
again for more than 4 seconds, the installer permission level
switches back to End user.
To set the user permission level to Advanced end user
1 Go to the main menu or any of its submenus:
2 Press for more than 4 seconds.
Result: The user permission level switches to Adv. end user.
Additional information is displayed and "+" is added to the menu title.
The user permission level will stay in Adv. end user until set
otherwise.
To set the user permission level to End user
1 Press for more than 4 seconds.
Result: The user permission level switches to End user. The user
interface will return to the default home screen.
To modify an overview setting
Example: Modify [1‑01] from 15 to 20.
1 Go to [A.8]: > Installer settings > Overview settings.
2 Go to the corresponding screen of the first part of the setting by
using the and button.
INFORMATION
An additional 0-digit is added to the first part of the setting
when you access the codes in the overview settings.
Example: [1‑01]: "1" will result in "01".
Overview settings
01
00 00 01 15 02 00
04 05 06
08 09 0a
0c 0d 0e
Confirm Adjust Scroll
3 Go to the corresponding second part of the setting by using the
and button.
Overview settings
01
00 00 01 15 02 00
04 05 06
08 09 0a
0c 0d 0e
Confirm Adjust Scroll
Result: The value to be modified is now highlighted.
4 Modify the value by using the
Overview settings
01
00 00 01 20 02 00
04 05 06
08 09 0a
0c 0d 0e
Confirm Adjust Scroll
5 Repeat previous steps if you have to modify other settings.
6 Push to confirm the modification of the parameter.
7 At installer settings menu, press
Installer settings
The system will restart.
OK Cancel
Confirm Adjust
Installation manual
14
.
03 00
07
0b
0f
03 00
07
0b
0f
and button.
03 00
07
0b
0f
to confirm the settings.
Result: The system will restart.
5.1.3 To copy the system settings from the first
to the second user interface
If a second user interface is connected, the installer must first
proceed below instructions for the proper configuration of the 2 user
interfaces.
This procedure offers you also the possibility to copy the language
set from one user interface to the other one: e.g. from EKRUCBL2 to
EKRUCBL1.
1 When power is turned on for the first time, both user interfaces
display:
Tue
U5:Auto address
Push 4 sec. to continue
2 Push for 4 seconds on the user interface on which you want
to proceed to the quick wizard. This user interface is now the
main user interface.
INFORMATION
During the quick wizard, the second user interface displays
Busy and will NOT be possible to operate.
3 The quick wizard will guide you.
4 For proper operation of the system, the local data on the two
user interfaces must be the same. If this is NOT the case, both
user interfaces will display:
Synchronization
Data difference detected.
Please select action:
Send data
Confirm Adjust
5 Select the required action:
▪ Send data: the user interface you are operating contains the
correct data and the data on the other user interface will be
overwritten.
▪ Receive data: the user interface you are operating does
NOT contain the correct data and the data on the other user
interface will be used to overwrite.
6 The user interface requests confirmation if you are sure to
proceed.
Start copy
Are you sure you want to
start the copy operation?
OK Cancel
Confirm Adjust
7 Confirm the selection on the screen by pushing
(languages, schedules etc.) will be synchronised from the
selected source user interface to the other one.
Daikin Altherma low temperature monobloc
15:10
and all data
EBLQ+EDLQ011~016CAV3+W1
4P522031-1 – 2018.01