Notice - Philips 24PFL3603 User Manual

1 Notice

Trademarks are the property of Koninklijke Philips N.V. or their
respective owners.
Funai Corporation reserves the right to change products at any time
without being obliged to adjust earlier supplies accordingly.
The material in this Owner's manual is believed adequate for the
intended use of the system. If the product or its individual modules or
procedures are used for purposes other than those specified herein,
confirmation of their validity and suitability must be obtained. Funai
Corporation warrants that the material itself does not infringe any
United States patents. No further warranty is expressed or implied.
Funai Corporation cannot be held responsible neither for any errors
in the content of this document nor for any problems as a result of the
content in this document. Errors reported to Funai Corporation will be
adapted and published on the Funai Corporation support website as
soon as possible.
Pixel characteristics
This LCD product has a high number of color pixels. Although it has
effective pixels of 99.999% or more, black dots or bright points of light
(red, green or blue) may appear constantly on the screen. This is a
structural property of the display (within common industry standards)
and is not a malfunction.
Warranty
No components are user serviceable. Do not open or remove covers
to the inside of the product. Repairs may only be done by service
centers and official repair shops. Failure to do so shall void any
warranty, stated or implied.
Any operation expressly prohibited in this manual, any adjustments
or assembly procedures not recommended or authorized in this
manual shall void the warranty.
Federal communications commission notice
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio or television technician
for help.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Declaration of conformity
: PHILIPS
Trade name
: Funai Corporation, Inc.
Responsible party
: 24PFL3603
Model
: 19900 Van Ness Avenue, Torrance, CA 90501
Address
U.S.A.
Telephone number : 1 866 813 3283
Modifications
This apparatus may generate or use radio frequency energy. Changes
or modifications to this apparatus may cause harmful interference.
Any modifications to the apparatus must be approved by Funai
Corporation.
The user could lose the authority to operate this apparatus if an
unauthorized change or modification is made.
Cables
Connections to this device must be made with shielded cables with
metallic RFI / EMI connector hoods to maintain compliance with FCC
Rules and regulations.
Canadian notice
CAN ICES-3 (B) / NMB-3 (B)
Analog and digital television receiving apparatus, Canada BETS-7 /
NTMR-7.
Positioning the TV
Large screen TVs are heavy. 2 people are required to carry and
handle a large screen TV.
Make sure to hold the upper and bottom
frames of the unit firmly as illustrated.
Install the unit in a horizontal and stable
position.
Do not install the unit in direct sunlight or in
a place subject to dust or strong vibration.
Depending on the environment, the
temperature of this unit may increase
slightly. This is not a malfunction.
When installing this unit in a temperate environment, avoid a place
with rapid temperature changes.
Operating temperature: 41°F (5°C) to 104°F (40°C)
–
This unit should not be used in a tropical environment as it has not
been evaluated under such conditions.
No objects should be placed directly on or under this unit, especially
lighted candles or other flaming objects.
Depending on your external devices, noise or disturbance of the
picture and/or sound may be generated if the unit is placed too
close to them. In this case, please ensure enough space between
the external devices and the unit.
Do not insert the AC power cord into the power socket outlet before
all the connections are made.
Ensure that you always have easy access to the AC power cord and
outlet to disconnect the TV from the AC outlet.
Before you move the TV, disconnect attached cables to prevent
damage to connectors, especially the TV tuner.
Be sure to unplug the AC power plug from the AC outlet before
moving or carrying the unit.
When moving the TV and then setting it down, please be careful not
to pinch the AC power cord under the unit.
Do not place this unit in an area where it may be exposed to water,
oil or grease such as:
near a bathtub, basin, kitchen sink, washing tub, swimming pool,
kitchen exhaust fan, etc., or in a damp basement.
5 .
English