Hardware Installation; Live View - Honeywell MAXPRO NVR XE Quick Install Manual

1

Hardware Installation

Connect Peripherals — Dedicated Network Scenario
The installation below demonstrates a static IP network configuration. For DHCP based
configurations (such as a corporate WAN network), please refer to the Commissioning and
Installation guide on your software/documentation DVD.
1. Install the MAXPRO NVR XE unit on a flat surface.
2. Connect the keyboard, mouse and power cable (supplied), and then connect a
monitor and Honeywell IP camera(s). You will also require a network PoE switch to
connect the IP camera(s). Your system may include some or all of these typical system
components.
Monitor
(not supplied)
Network
USB
®
MAXPRO NVR XE
CAT5e to Network Port 1
CAT5e
Network PoE Switch (not supplied)
CAT5e
CAT5e CAT5e
HD55IP
Outdoor, 720p
HD45IP
Indoor, 720p
Honeywell IP cameras. Contact your dealer to purchase.
Rear Panel Connections — Dedicated Network Scenario
Serial
connector
Network port 2
Network port 1
Serial
(not used) Connect to PoE switch
connector
(not supplied)
Display port 24V USB
USB 2.0 (x4) DB15 connector.
Connect to USB keyboard, Connect to VGA
mouse (supplied). monitor
(not supplied).
2
Honeywell IP Camera Configuration
Using the MAXPRO NVR Wizard (3 Clicks to Live Video)
Power up the MAXPRO NVR XE unit. When the
Log On dialog box displays, log on as Windows
Administrator (Username: Administrator,
Password: Password1). The setup wizard starts
automatically but may take two minutes.
1. The CONFIGURATION page displays.
When the network is ready (network icon in
Windows tray), click
the default settings and proceed to
CAMERA DISCOVERY.
To modify the settings for your unique
system requirements, follow the table
below. After initial setup, you can do this in
the MAXPRO NVR client.
Field
Video Format
Start Recording
USB
VGA
Auto IP
Assignment
Dynamic IP
Synchronization
Auto Add
Discovered
Camera
Custom Camera
Credentials
CAT5e
Camera Type
Username,
Password
Camera IP
Range
HD44IP
Click
Indoor, VGA
saving any changes.
HD54DIP
Outdoor, VGA 2. The CAMERA DISCOVERY page displays.
Each newly connected camera is identified
and an IP address is assigned to the
camera by the Wizard, after which the
camera reboots.
I t may take a few minutes before cameras are
discovered and added. You will see a Discovery
in progress... indicator as well as a pop-up
message on the lower right of your monitor. The
PS/2
list disappears as the cameras are added to the
connector
MAXPRO NVR.
Click
cameras are discovered and added.
Click
CONFIGURATION page.
3. The INSTALLATION page displays. Click
to start the MAXPRO NVR
application (see
Note To add non-Honeywell devices, see
PS/2
Third Party Device
connector
Audio In/OUT
(not used)
STEP 1 CONFIGURATION
to accept
Description
NTSC, PAL
Start recording as soon as the
camera is added in MAXPRO NVR.
Software assigns IP address
automatically.
Software synchronizes any change
in a device's IP address.
STEP 2 CAMERA DISCOVERY
Any newly connected device is
automatically added to the devices
list.
Not configurable in the Wizard.
Not configurable in the Wizard.
Not configurable in the Wizard.
The system automatically detects
all cameras in this range on the
network.
to reset the values without
Pop-up
message
STEP 3 INSTALLATION
only after all connected
to return to the
3 Live View).
Configuration.
3

Live View

Log on to the MAXPRO NVR Viewer
1. As soon as you click in the Setup
Wizard, the Log On dialog displays. Please wait
while the system logs you on automatically as a
Windows Logged-In User.
2. MAXPRO NVR launches and the Viewer tab
displays (see below). The Devices area on the
left hand pane lists all the discovered network
cameras.
View Live Video
To view video from cameras, double-click MAXPRO NVR in the Devices list to display video
from all discovered cameras in the Viewer. You can also highlight and drag each camera into a
panel.
List of Honeywell IP
cameras connected to
and discovered by
MAXPRO NVR.
Devices tab: currently active.
Alarms tab: acknowledge and
clear alarms.
Images/Clips: select images and
clips to view.
Double-click or drag the clip to a
Viewer panel to view.
To export a clip for forensics,
click Clip Export.
Live viewer player controls
Live Viewer Player Controls
Time jump control to
quickly locate video
Pause
Change
Play backward Play forward
Timeline playing speed
User currently
logged on
Select date and time
to start recording
Number of alarms
detected