Roland RD-700SX Owner's Manual page 141

111: *OVDRV→CHO (OVERDRIVE→
CHORUS)
This effect connects an overdrive and a chorus in series.
Assignable Parameters
MFX Control Chorus Bal, Chorus Rate, OD Drive
Parameter Value
OD Drive 0–127
OD Pan L64–0–63R
Chorus PreDly 0.0–100.0 ms
Chorus Rate 0.05–10.00
Hz
Chorus Depth 0–127
Chorus Bal D100:0W–
D0:100W
Level 0–127
112: *OVDRV→FLN
(OVERDRIVE→FLANGER)
This effect connects an overdrive and a flanger in series.
Assignable Parameters
MFX Control Flngr Bal, Flngr Rate, OD Drive
Parameter Value
OD Drive 0–127
OD Pan L64–0–63R
Flngr PreDly 0.0–100.0 ms
Flngr Rate 0.05–10.00
Hz
Flngr Depth 0–127
Flngr Fbk -98– +98%
Flngr Bal D100:0W–
D0:100W
Level 0–127
Description
Adjust the degree of overdrive
distortion. The volume will change
together with the degree of distortion.
Adjust the stereo location of the
overdrive sound. L64 is far left, 0 is
center, and 63R is far right.
Adjust the time delay from when the
direct sound begins until the chorus
sound is heard.
Adjust the modulation speed of the
chorus effect.
Adjust the modulation depth of the
chorus effect.
Adjust the volume balance between the
overdrive sound that is sent through the
chorus and the overdrive sound that is
not sent through the chorus. With a
setting of "D100:0W," only the
overdrive sound will be output. With a
setting of "D0:100W," only the
overdrive sound that is sent through the
chorus will be output.
Adjust the output level.
Description
Adjust the degree of overdrive
distortion. The volume will change
together with the degree of distortion.
Adjust the stereo location of the
overdrive sound. L64 is far left, 0 is
center, and 63R is far right.
Adjust the time delay from when the
direct sound begins until the flanger
sound is heard.
Adjust the modulation speed of the
flanger effect.
Adjust the modulation depth of the
flanger effect.
Adjust the proportion (%) of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Adjust the volume balance between the
overdrive sound that is sent through the
flanger and the overdrive sound that is
not sent through the flanger. With a
setting of "D100:0W," only the
overdrive sound will be output. With a
setting of "D0:100W," only the
overdrive sound that is sent through the
flanger will be output.
Adjust the output level.
113: *OVDRV→DLY (OVERDRIVE→
DELAY)
This effect connects an overdrive and a delay in series.
Assignable Parameters
MFX Control Delay Bal, OD Drive
Parameter Value
OD Drive 0–127
OD Pan L64–0–63R
Delay Time 0.1–500.0 ms
Delay Feedback -98– +98%
Delay HF 200–8000 Hz,
Damp BYPASS
Delay Bal D100:0W–
D0:100W
Level 0–127
114: *DIST→CHO (DISTORTION→
CHORUS)
This effect connects distortion and chorus in series. The parameters
are essentially the same as "111: OD→CHORUS," with the exception
of the following two.
OD Drive → Dst Drive (Specify the amount of distortion.)
OD Pan → Dist Pan (Specify the stereo location of the distortion
sound.)
115: *DIST→FLNGR (DISTORTION→
FLANGER)
This effect connects distortion and flanger in series. The parameters
are essentially the same as in "112: OD→FLANGER," with the
exception of the following two.
OD Drive → Dst Drive (Specify the amount of distortion.)
OD Pan → Dist Pan (Specify the stereo location of the distortion
sound.)
116: *DIST→DELAY (DISTORTION→
DELAY)
This effect connects distortion and delay in series. The parameters are
essentially the same as in "113: OD→DELAY," with the exception of
the following two.
→Dst Drive (Specify the amount of distortion.)
OD Drive
→Dist Pan (Specify the stereo location of the
OD Pan
distortion sound.)
Effect/Parameter List
Description
Adjust the degree of overdrive
distortion. The volume will change
together with the degree of distortion.
Adjust the stereo location of the
overdrive sound. L64 is far left, 0 is
center, and 63R is far right.
Adjust the time delay from when the
direct sound begins until the delay
sound is heard.
Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Adjust the frequency above which
delayed sound fed back to the effect will
be cut. If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Adjust the volume balance between the
overdrive sound that is sent through the
delay and the overdrive sound that is
not sent through the delay. With a
setting of "D100:0W," only the
overdrive sound will be output. With a
setting of "D0:100W," only the
overdrive sound that is sent through the
delay will be output.
Adjust the output level.
141