Roland RD-700SX Owner's Manual page 119

29: 3D CHORUS
This applies a 3D effect to the chorus sound. The chorus sound will be
positioned 90 degrees left and 90 degrees right.
Assignable Parameters
MFX Control Depth, Rate, Balance
Parameter Value
Filter Type OFF,
LPF,
HPF
Cutoff Freq 200–8000 Hz
Pre Delay 0.0–100.0 ms
Rate Mode Hz, note
Rate (Hz) 0.05–10.00
Hz
note (*1)
Rate ( )
Depth 0–127
Phase 0–180 deg
Output Mode SPEAKER,
PHONES
Low Gain -15– +15 dB
High Gain -15– +15 dB
Balance D100:0W–
D0:100W
Level 0–127
30: 3D FLANGER
This applies a 3D effect to the flanger sound. The flanger sound will be
positioned 90 degrees left and 90 degrees right.
Assignable Parameters
MFX Control Depth, Rate, Feedback, Balance
Parameter Value
Filter Type OFF,
LPF,
HPF
Cutoff Freq 200–8000 Hz
Pre Delay 0.0–100.0 ms
Rate Mode Hz, note
Rate (Hz) 0.05–10.00
Hz
note (*1)
Rate ( )
Depth 0–127
Phase 0–180 deg
Feedback -98– +98 %
Description
Type of filter
OFF: No filter is used
LPF: Cuts the frequency range above
the Cutoff Freq
HPF: Cuts the frequency range below
the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from the direct
sound until the chorus sound is heard.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of modulation (Hz)
Frequency of modulation (note)
Modulation depth of the chorus effect
Spatial spread of the sound
Adjusts the method that will be used to
hear the sound that is output to the
OUTPUT jacks. The optimal 3D effect
will be achieved if you select SPEAKER
when using speakers, or PHONES when
using headphones.
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the chorus sound (W)
Output Level
Description
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above
the Cutoff Freq
HPF: cuts the frequency range below
the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from when the
direct sound begins until the flanger
sound is heard.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of modulation (Hz)
Frequency of modulation (note)
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Parameter Value
Output Mode SPEAKER,
PHONES
Low Gain -15– +15 dB
High Gain -15– +15 dB
Balance D100:0W–
D0:100W
Level 0–127
31: 3D S.FLANGR (3D STEP FLANGER)
This applies a 3D effect to the step flanger sound. The flanger sound
will be positioned 90 degrees left and 90 degrees right.
Assignable Parameters
MFX Control StepRate, Depth, Feedback, Balance
Parameter Value
Filter Type OFF,
LPF,
HPF
Cutoff Freq 200–8000 Hz
Pre Delay 0.0–100.0 ms
Rate Mode Hz, note
Rate (Hz) 0.05–10.00
Hz
note (*1)
Rate ( )
Depth 0–127
Phase 0–180 deg
Feedback -98– +98 %
Step Rate Mode Hz, note
StepRate(Hz) 0.10–20.00
Hz
Step Rate note (*1)
( )
Output Mode SPEAKER,
PHONES
Low Gain -15– +15 dB
High Gain -15– +15 dB
Balance D100:0W–
D0:100W
Level 0–127
Effect/Parameter List
Description
Adjusts the method that will be used to
hear the sound that is output to the
OUTPUT jacks. The optimal 3D effect
will be achieved if you select SPEAKER
when using speakers, or PHONES when
using headphones.
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the flanger sound (W)
Output Level
Description
Type of filter
OFF: No filter is used
LPF: Cuts the frequency range above
the Cutoff Freq
HPF: Cuts the frequency range below
the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from when the
direct sound begins until the flanger
sound is heard.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of modulation (Hz)
Frequency of modulation (note)
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
When this is set to "note," the effect is
synchronized with the tempo.
Rate (period) of pitch change (Hz)
Rate (period) of pitch change (note)
Adjusts the method that will be used to
hear the sound that is output to the
OUTPUT jacks. The optimal 3D effect
will be achieved if you select SPEAKER
when using speakers, or PHONES when
using headphones.
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the flanger sound (W)
Output Level
119