3D Flanger; 3D Step Flanger; 2Band Chorus - Roland GW-8 Owner's Manual

30:

3D FLANGER

This applies a 3D effect to the flanger sound. The flanger sound will
be positioned 90 degrees left and 90 degrees right.
fig.MFX-30
L
3D Flanger
R
Parameter Value
Filter Type OFF, LPF, HPF
Cutoff Freq 200–8000 Hz
Pre Delay 0.0–100.0 ms
Rate 0.05–10.00 Hz, note
Depth
0–127
Phase 0–180 deg
Feedback -98– +98%
Output Mode SPEAKER, PHONES
Low Gain -15– +15 dB
High Gain
-15– +15 dB
Balance D100:0W–D0:100W
Level 0–127
31:

3D STEP FLANGER

This applies a 3D effect to the step flanger sound. The flanger sound
will be positioned 90 degrees left and 90 degrees right.
fig.MFX-31
L
3D Step Flanger
R
Parameter Value
Filter Type
OFF, LPF, HPF
Cutoff Freq 200–8000 Hz
Pre Delay
0.0–100.0 ms
Rate 0.05–10.00 Hz, note
Depth 0–127
Phase
0–180 deg
2-Band
L out
EQ
2-Band
R out
EQ
Description
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Adjusts the method that will be
used to hear the sound that is out-
put to the OUTPUT jacks. The op-
timal 3D effect will be achieved if
you select SPEAKER when using
speakers, or PHONES when using
headphones.
Gain of the low range
Gain of the high range
Volume balance between the di-
rect sound (D) and the flanger
sound (W)
Output Level
2-Band
L out
EQ
2-Band
R out
EQ
Description
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Parameter Value
Feedback
-98– +98%
Step Rate 0.10–20.00 Hz, note
Output Mode SPEAKER, PHONES
Low Gain -15– +15 dB
High Gain
-15– +15 dB
Balance D100:0W–D0:100W
Level 0–127
32:

2BAND CHORUS

A chorus effect that lets you apply an effect independently to the low-
frequency and high-frequency ranges.
fig.MFX-32
L in
High Band Chorus
Split
Low Band Chorus
High Band Chorus
Split
Low Band Chorus
R in
Parameter Range
Split Freq 200–8000 Hz
Low Pre Delay 0.0–100.0 ms
Low Rate 0.05–10.00 Hz, note
Low Depth
0–127
Low Phase 0–180 deg
High Pre Delay 0.0–100.0 ms
High Rate 0.05–10.00 Hz, note
High Depth 0–127
High Phase 0–180 deg
Balance D100:0W–D0:100W
Level 0–127
Effects List
Description
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Rate (period) of pitch change
Adjusts the method that will be
used to hear the sound that is out-
put to the OUTPUT jacks. The op-
timal 3D effect will be achieved if
you select SPEAKER when using
speakers, or PHONES when using
headphones.
Gain of the low range
Gain of the high range
Volume balance between the di-
rect sound (D) and the flanger
sound (W)
Output Level
L out
R out
Explanation
Frequency at which the low and
high ranges will be divided
Delay time from when the origi-
nal sound is heard to when the
low-range chorus sound is heard
Rate at which the low-range cho-
rus sound is modulated
Modulation depth for the low-
range chorus sound
Spaciousness of the low-range
chorus sound
Delay time from when the origi-
nal sound is heard to when the
high-range chorus sound is
heard
Rate at which the low-range cho-
rus sound is modulated
Modulation depth for the high-
range chorus sound
Spaciousness of the high-range
chorus sound
Volume balance of the original
sound (D) and chorus sound (W)
Output volume
67