Datavideo HRS-30 Instruction Manual
  1. Manuals
  2. Brands
  3. Datavideo Manuals
  4. Voice Recorder
  5. HRS-30
  6. Instruction manual
Datavideo HRS-30 Instruction Manual

Datavideo HRS-30 Instruction Manual

Fieldside hand carry recorder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FIELDSIDE HAND
CARRY RECORDER
HRS-30
Instruction Manual
w w w . d a t a v i d e o . c o m

Advertisement

Table of Contents
loading

Related Manuals for Datavideo HRS-30

Summary of Contents for Datavideo HRS-30

  • Page 1 FIELDSIDE HAND CARRY RECORDER HRS-30 Instruction Manual w w w . d a t a v i d e o . c o m...

  • Page 2: Table Of Contents

    Connecting the 2.5’’HDD to PC ............................ 34 Connecting the 2.5’’HDD to MAC ..........................35 Q & A ....................................36 HRS-30 Error Codes ..............................37 HRS-30 RS-232 Control Command ..........................38 Example HRS-30 Set Up ............................... 42 RJ-45 Pin Define ................................44 Dimensions ..................................44 Specifications ................................
  • Page 3 Disclaimer of Product & Services The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try to give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this manual, from time to time, may not be correct or may be incomplete. This manual may contain typing errors, omissions or incorrect information.

  • Page 4: Fcc Compliance Statement

    7. This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company.

  • Page 5: Warranty

    Drive, Solid State Drive, SD Card, USB Thumb Drive, Lighting, Camera module, PCIe Card are covered for 1 year. • The three-year warranty must be registered on Datavideo's official website or with your local Datavideo office or one of its authorized distributors within 30 days of purchase. Disposal...

  • Page 6: Unpacking The Hrs-30

    Unpacking the HRS-30 Place the HRS-30 on a level desk or surface. The carry handle will be at the right side facing the operator’s position. To open the HRS-30 monitor lid slide the thumb catches in the direction shown to their outer most position. Then lift the monitor lid upwards away from the keyboard and carry handle.

  • Page 7: Hrs-30 & Battery

    HRS-30 & Battery The HRS-30 can be powered from a standard V-Mount battery connection or mains power. This enables you to power the HRS-30 using an existing camera battery. HRS-30: with V-mount Battery Plate...

  • Page 8: Rear Panel

    HRS-30 can use an internal or external time code source. In RECORD state, the source time code will through to output. In PLAY state, the output time code source is from the HRS-30 playing file. Stereo Phone Jack Plug For audio output. The phone volume is controlled by the Audio Level Adjustments (on the Monitor Operation Keyboard).

  • Page 9: Monitor Operation Keyboard

    Stereo Phone Jack Plug For stereo headphones. The headphone volume is controlled by the Audio Level Adjustments. When this phone jack connected earphone, the HRS-30 speaker function will disable. Audio Level Adjustments Allow you to adjust the headphones volume. Aspect Ratio Button Sets the LCD aspect ratio to 4.3, 16:10, or 16:9...

  • Page 10: Monitor Menu Options

    Monitor Menu Options PICTURE Step 1. Press the button into the monitor system setting mode. Step 2. Press button into the PICTURE setting position. Step 3. Press button again into the BRIGHTNESS setting position. Step 4. Press button to setting the BRIGHTNESS values from 0~100 Step 5.

  • Page 11: Func

    FUNC Step 1. Press the button two times move to the monitor FUNC setting mode. Step 2. Press button into the FUNC setting position. Step 3. Press button again to setting the CENTER MARK ON/OFF on the screen. Step 4. Press button moving to the SAFETY ZONE setting.

  • Page 12: Setup

    SETUP Step 1. Press the button three times move to the monitor SETUP setting mode. Step 2. Press button move to the SETUP setting position. Step 3. Press button again into to the OSD TIME setting position. Step 4. Press button to setting the OSD display on screen time (value from 5~60 SECONDS).

  • Page 13: Advanced

    ADVANCED Step 1. Press the button four times into the monitor ADVANCED setting mode. Step 2. Press button into the RESET setting position. Step 3. Press button again which will return all the settings of the monitor to the factory defaults. Step 4.

  • Page 14: Recorder Operation Keyboard

    Enter or Skip 8 sec. Enter Key: Confirm your Recorder Operation select, display on 2’’ LCD panel. In order to activate Skip 8 sec. function while HRS-30 is playing a video clip, press Skip 8 sec. button and then press Soft Keys to skip forward by 8~10 seconds or backward 8 ~ 10 seconds (depending on the recorded format).
  • Page 15 To start recording press the Record Button and Play Button simultaneously. Note1: Unit will not record if no video signal is present. Note2: In HRS-30 play state, press Record button, 2’’ LCD Display Panel will show the FILE FORMAT and BIN FILE LENGTH information; press Record button again will return to normal.

  • Page 16: Recorder Display Panel Status

    Recorder Display Panel Status 08h19m 00 : 00: 12; 28 BIN 01 CLIP01 0 0 : 0 0 : 0 0 SYMBOL DESCRIPTION Type A: connect DC power indication Type B: connect battery power indication Loop Playback indicator Remaining Recording Space in Hours and Minutes 08h19m Current Time Code or total length of CLIP 00:00:12;28...

  • Page 17: Recorder Menu Key Options

    Recorder Menu Key Options TOOL FIRMWARE REVISION Display the HRS-30 firmware information: CODEC, HOST, REC…etc. Step 1. Press the (MENU) button into the menu mode. [ MENU ] TOOL SETUP STATUS DOWN Step 2. Press the (ENTER) button into the TOOL menu.

  • Page 18: Erase This Bin

    ERASE THIS BIN ERASE THIS BIN is used for deleting individual bins from the HRS-30. Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (ENTER) button into the TOOL menu. Step 3. Press the (UP) button / (DOWN) button select to the ERASE THIS BIN menu.

  • Page 19: Format Media

    (ENTER) button to format the selected bin - The bin duration will return to 00:00:00:00 After a few seconds the HRS-30 will return to normal. NOTE: When your 2.5’’ HDD contains media, the first time you connect the HDD to computer, the computer...

  • Page 20: Uprgrade Firmware

    Step 5. Copy the firmware update file (flash.bin) to the root directory of 2.5’’ HDD. Step 6. Safe remove the 2.5” HDD cable. Step 7. Insert the 2.5’’ HDD in the HRS-30 and select the UPGRADE FIRMWARE option and follow the structions.

  • Page 21: Un-Lock Media

    UN-LOCK MEDIA After you record file at HRS-30, the 2.5’’HDD format become read only. To set disk writable please do UN-LOCK MEDIA. Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (ENTER) button into the TOOL menu.

  • Page 22: Setup

    SETUP RECORD SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (UP) button / (DOWN) button select to the SETUP menu. [ MENU ] TOOL SETUP STATUS DOWN Step 3. Press the (ENTER) button into the SETUP menu. [ SETUP ] REC SETUP PLAY SETUP...
  • Page 23 Step 5. Press the (UP) button / (DOWN) button to select the HD ENCODE FORMAT / SD ENCODE FORMAT / REC FILE TYPE / REC CHANNEL NUM / SD ASPECT RATIO / TIME LAPSE / PWR- ON AUTO REC menu. Step 6.
  • Page 24 NUMBERS OF AUD CH - Audio channel selection: User can select to record 2, 4 or 8 audio channels. [ NUMBERS OF AUD CH ] DOWN SD ASPECT RATIO - Sets the SD aspect ratio to 16:9 or 4:3. [ SD ASPECT RAITIO ] 4 : 3 16 : 9 DOWN...

  • Page 25: Play Setup

    PLAY SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (DOWN) button select to the SETUP menu. Step 3. Press the (ENTER) button into the SETUP menu. [ SETUP ] REC SETUP PLAY SETUP SYSTEM SETUP SAVE SETUP RECALL SETUP...
  • Page 26 When LOOP PLAY mode is off, HRS-30 will pause at the end of the CLIP. BIN = When LOOP PLAY mode is on, HRS-30 will play all CLIPs of BIN file until it reaches to the end of last CLIP; it will then loop back to beginning of the CLIP 1.

  • Page 27: System Setup

    SYSTEM SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (DOWN) button select to the SETUP menu. Step 3. Press the (ENTER) button into the SETUP menu. Step 4. Press the (UP) button / (DOWN) button select to the SYSTEM SETUP menu.
  • Page 28 DISABLE ENABLE DOWN Note: When this function enable, other button function will disable. BUZZER Setting the BUZZER function on / off. This buzzer will be activated to alarm if there is an "unrecoverable" defect of HRS-30. [ BUZZER ] DOWN...
  • Page 29 LONG TIME STOP Setting the HOLD 1 SECONDS TO STOP function on / off. [ LONG TIME STOP ] DOWN DATE & TIME SETUP Into the DATE & TIME SETUP mode, use the (UP) / (DOWN) / (Fwd ) / (Rew) buttons to setting the DATE &...

  • Page 30: Save Setup

    SAVE SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (DOWN) button into the SETUP menu. Step 3. Press the (ENTER) button into the SETUP menu. Step 4. Press the (UP) button / (DOWN) button select to the SAVE SETUP menu. [ SETUP ] REC SETUP PLAY SETUP...

  • Page 31: Recall Setup

    RECALL SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (DOWN) button into the SETUP menu. Step 3. Press the (ENTER) button into the SETUP menu. Step 4. Press the (UP) button / (DOWN) button select to the RECALL SETUP menu. [ SETUP ] REC SETUP PLAY SETUP...

  • Page 32: Status

    STATUS Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (UP) button / (DOWN) button select to the STATUS menu. [ MENU ] TOOL SETUP STATUS DOWN Step 3. Press the (ENTER) button into the STATUS menu. Step 4.

  • Page 33: Assemble 2.5" Hdd In Removable Rack

    Step 1. Put the 2.5" HDD into the rack. Step 2. Assemble four screws to fasten 2.5" HDD on the rack. Step 3. Push the button to Left side and then push the rack into HRS-30. Step 4. Push the button to right side, for lock the rack.

  • Page 34: Connecting The 2.5''Hdd To Pc

    The HRS-30 system files type: 1. One BIN = 99 CLIP (max). 2. HRS-30 REC over 10 hours will add one CLIP. 3. When you pause / stop REC or REC error, the HRS-30 system will add one CLIP.

  • Page 35: Connecting The 2.5''Hdd To Mac

    Please connect two USB to your MAC. Step 2. A Datavideo drive will appear on the desktop. Step 3. If you access the drive you will see the files are available for copying across to a local drive, or direct access.

  • Page 36: Q & A

    What causes the HRS-30 to show “WRONG MEDIA” on the 2’’ LCD Display Panel? Ans: 1. If HDD drive is used for the first time, HRS-30 will show “WRONG MEDIA” on the 2’’ LCD Display Panel for remind you to format HDD, so please format the HDD.

  • Page 37: Hrs-30 Error Codes

    HRS-30 Error Codes 01: Interface FPGA no response when boot 02: Recorder FW no response when boot 03: Codec FW no response when boot 04: Main board and Controller connect error. 10: Recorder FW wrong stop by itself while recording...

  • Page 38: Hrs-30 Rs-232 Control Command

    HRS-30 RS-232 Control Command 1. Interface Overview  Standard transmission rate on the interface bus is 38400 bits per seconds (bps)  1 Start bit + 8 Data bits + 1 Parity bit + 1 Stop bit. Odd Parity 2. Command Table...
  • Page 39 The“00h, 11h, 11h : DEVICE TYPE REQUEST” command is used for asking the specifications of the HRS-30 used as DEVICE. When the DEVICE receives this command, it attaches 2-bytes specification data to “12h 11h : DEVICE TYPE” and sends the information to the CONTROLLER.
  • Page 40 4. Trick Play 21h 13h nn csum : Shuttle Forward 21h 23h nn csum : Shuttle Reverse speed Command Forward Command Reverse 21h 13h 62h 96h 21h 23h 62h A6h 5E h 21h 13h 5Eh 92h 21h 23h 5Eh A2h 58 h 21h 13h 58h 8Ch 21h 23h 58h 9Ch...
  • Page 41 7. Variable Status Sense 61h, 20 h, xnh, csum The return-byte is variable for Status Sense. The 3 byte of command: MSD (Bit7~4, x): Indicates the initial byte index of the to be returned. LSD (Bit3~0, n): Indicates the number of data bytes to be returned. 8.

  • Page 42: Example Hrs-30 Set Up

    Example HRS-30 Set Up Type A:...
  • Page 43 Type B:...

  • Page 44: Rj-45 Pin Define

    RJ-45 Pin Define This pin define is use for RJ-45 connect to RS-232 connector. Dimensions All measurements in millimetres (mm).

  • Page 45: Specifications

    Specifications General Specification Video Standard HD/SD 1080P 23.97/24Hz 1080i 50/59.94/60Hz Video Format 720P 50/59.94/60Hz 480i / 576i 2.5" HDD / SSD, Max capacity 1T GB Storage Medium ＊Note: SSD is recommended Estimated Record Time SD:22(50Mbps) ~75(8Mbps) (min per 10GB) HD: 10 (125Mbps)~68 (10Mbps) How to retrieve Recorded Content Removable HDD/SSD, transfer data via USB 3.0 Recorded File Format...
  • Page 46 Panel Specification Screen size 10.1” 1280（H）× 800（V） Resolution 0.0565（W）× 0.1695（H）mm Dot pitch 216.96（W）× 135.60（H）mm Active Area Interface Support Video Input Signal 1 x SDI 1 x SDI(input loop thru) Monitoring/ Playback output 1 x HDMI ; 1 x SDI (Out) Analog Audio Input 1 x 3.5mm jack for external speaker Speakers 2 x 3W...
  • Page 47 Notes...
  • Page 48 Notes...
  • Page 49 Notes...

  • Page 50: Service & Support

    Service & Support It is our goal to make owning and using Datavideo products a satisfying experience. Our support staff is available to assist you to set up and operate your system. Contact your local office for specific support requests. Plus, DATAVIDEO WORLDWIDE OFFICES please visit www.datavideo.com to access our FAQ section.

Table of Contents