Currys Essentials CDWTT10 Installation Manual

Currys Essentials CDWTT10_IG_GB_p1_100210.pdf 1 2/10/10 2:59 AM
TABL E TOP DISH W A SH E R
IN ST AL LAT IO N M ANU A L
CD WT T10
Thank you for purchasing Currys Essentials dishwasher.
Please refer to this guide for the installation process.
1. Remove all packaging before positioning the machine. (Fig 1)
2. Ensure the dishwasher is installed by a quali ed technician. Refer to the tools required in Fig 2.
3. Ensure there is clearance each side of the unit to allow slight sideways movement for servicing
when required. Good levelling is essential for correct closure and sealing of the door. When the unit
is correctly levelled, the door should not catch the inner liner on either side of the cabinet. The
adjustable feet may be loosened or tightened in order to obtain the optimum levelling of the unit
(Fig 3)
4. The dimension of the dishwasher is 575(W) x 480(D) X 466(H) in mm.
Figure 3 outlines the minimum dimensions required to accommodate the table top dishwasher.
Protect plastic parts and cables from high temperatures.
5. Do not connect the unit to the mains before the installation. Ensure you are not
installing the unit right in front of the mains. This is to avoid potential damage to the back of the
unit. (Fig 5)
After installing the appliance, ensure that the plug is easily accessible.
6. The electrical connection conditions must correspond with the speci cations on the
rating plate of the dishwasher. Do not use extension cables.
7. Position the unit next to a water tap (Fig 4) and a drain. Level the unit if needed.
Ensure the water inlet and drain hoses are not kinked or squashed (Fig 6). The unit must not stand
on the electrical supply cable.
8. Make sure your plumbing is suitable for use with the dishwasher. If in doubt contact a
quali ed plumber. This unit MUST BE connected to COLD WATER MAINS using the new water inlet
hose. OLD HOSE SETS MUST NOT BE RE-USED. The water pressure from the water mains needs to
be at a minimum of 0.03 MPa and a maximum of 1.00MPa.
• Connect one end of the safety water supply hose to your dishwasher, and then
connect the other end of the hose to your water mains as Fig A. Please ensure the black
rubber seal is in place.
• Connect one end of the drain hose to your dishwasher, and the other end to the drain.
• Turn on your water mains and check for leakages after connecting the hose.
• Connect the dishwasher to the electrical mains outlet.
NOTE: YOU MAY USE THE Y-ADAPTOR (NOT INCLUDED) FOR
ADDITIONAL WATER FEED FOR ANOTHER APPLIANCE, FOR
INSTANCE A WASHING MACHINE. THIS IS ONLY APPLICABLE
FOR COLD WATER MAINS. A Y-ADAPTOR IS AVAILABLE
FROM MOST DIY STORES. (Fig A)
• Do not bend the drain hose. (Fig B)
• Do not lift the drain hose higher than 10 cm from
the table top, otherwise the unit may not be able to expel
the waste water properly. (Fig C)
• Secure the water drain hose to the waste pipe to
avoid it coming o during washing process. (Fig 9 and D)
NOTE: THE WASTE PIPE MUST ONLY BE CONNECTED TO
THE FOUL DRAINS AND NOT THE SURFACE WATER
DRAINAGE SYSTEM.
THE WATER DRAIN HOSE SHOULD BE PLACED
BETWEEN 40 CM AND 100 CM FROM THE FLOOR
LEVEL AND MUST NOT BE EXTENDED, OTHERWISE THE
UNIT MAY NOT BE ABLE TO EXPEL THE WASTE WATER
PROPERLY.
YOU MAY USE THE U-SHAPED DRAIN HOSE HOLDER TO
SECURE YOUR DRAIN HOSE AND TO AVOID BENDING IT.
A
water mains
Y-Adaptor
(not included)
Connect to
another
appliance
if required.
water supply hose
B
C
max.
10cm
D