Advertisement
CONFIGURE THE 5877
ENROLLING A CONTROL PANEL INTO THE MODULE
If the device connected to the module is intended to be controlled directly
from a control panel, the control panel must be enrolled into the module
using the module's serial number.
IMPORTANT: Enrollment of a control panel into the 5877 is
available only with controls that support this feature (ex. LYNX
Touch ver. 6.0 or higher).
To enroll the control panel into the module, refer to the panel's
programming instructions. Enrolling typically includes these steps:
1.
At the control, navigate to the appropriate serial number input
prompt and manually enter the module's serial number (see the
module's serial number label).
2.
To confirm enrollment, press the "Learn" button and listen for the
module's relay to "click."
ENROLLING WIRELESS KEYS INTO THE MODULE
NOTE: The 5877 supports both high security and regular mode.
Wireless key LED blinks red when in high security mode.
Wireless key LED blinks green when in regular mode.
To enroll high security mode start on step 1.
To enroll regular mode start on step 2.
1. Set wireless key to high security mode
before enrolling in module (if desired):
Press and hold A-B-C for 2 seconds.
2. Press (one second) and release the
Program button on the 5877 module;
the LED will start flashing GREEN.
3. To enroll it, press the Wireless Key button that will be used to
trigger the relay and the LED will stop flashing GREEN. [Note: If
no Wireless Key button is pushed, the "enroll" program mode
times out after 2 minutes.]
4. Repeat the process for each Wireless Key button being used; up
to 6 buttons total.
5. Test by pressing each Wireless Key button enrolled in the relay
module; the relay module should click for each Wireless Key
button press.
SPECIFICATIONS
Electrical: 12VDC Power Supply; Operating Current 29-31mA
Environmental Conditions: 14° to 122° F (-10° to 50° C); < 90% RH (non-condensing)
Frequency: 345 MHz
Relay: Momentary dry contact closure; Normally Open or Normally Closed; 5A Form C
relay
Dimensions: 4.5" H x 2.75" W x 0.5" D; (114.3mm x 69.85mm x 12.7mm)
*Compatibility: Honeywell LYNX Series Controls, 5883H, 6160RF and 6150RF
Keypads produced after March 2007 (P/NSA6150RFAS-T3 Printed Circuit Board).
FEDERAL COMMUNICATIONS COMMISSION STATEMENT:
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User Manual. Unauthorized
changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your
information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class
B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or
eliminated.
• Move the radio or television receiver away from the
receiver/control.
Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the
properties of their respective owners. All rights reserved. Made in Taiwan.
For the latest U.S. warranty information, please visit: www.honeywell.com/security/hsc/resources/wa
or Please contact your local authorized Honeywell representative for product warranty information.
For the latest documentation and online support information:
https://mywebtech.honeywell.com/
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the
radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2012 Honeywell International Inc.
www.honeywell.com/security
TO DELETE ALL WIRELESS KEY BUTTONS
Press and continue to hold the Program button; the
LED turns RED, then turns off, then RED again;
release the Program button. This takes about 15
seconds.
ENABLING THE STATUS LED
(enrolling the control's RF House ID code into the
module)
NOTE: The System Control Panel must be capable of
transmitting system status [for example, a LYNX
Touch, LYNX Plus, or a VISTA Panel with a
compatible* transceiver (see Specifications)]. Ensure
the House ID is enabled in the panel programming.
1.
Press (one second) and release the Program
button; the LED will start flashing GREEN.
2.
IMMEDIATELY press (one second) and release
the Program button again. The LED will start
flashing ORANGE.
3.
Disarm or Arm the control panel. The LED stops
flashing ORANGE and then shows the status of
the control panel (see LED indications).
[Note: If no House ID code is enrolled, the enroll
program mode times out after 2 minutes.]
LED STATUS
Flashing RED
Solid RED
Solid GREEN
LED OFF
Flashing ORANGE
4.
Test the status by arming and disarming the
system in both AWAY and STAY Modes.
To Disable the LED, remove the Jumper next to
the LED.
APPROVALS / LISTINGS
• FCC part 15, Class B verified
• IC, ICES-003, Class B verified
COMPLIANCE NOTES
Product must be tested at least once each year.
REFER TO THE INSTALLATION INSTRUCTIONS FOR
THE RECEIVER/CONTROL WITH WHICH THIS DEVICE
IS USED FOR DETAILS REGARDING LIMITATIONS OF
THE ENTIRE ALARM SYSTEM.
FCC / IC STATEMENT:
This device complies with Part 15 of the FCC Rules and
Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference (2) This
device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la
FCC et exempt de licence de norme(s) RSS d'Industrie
Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer
d'interférences nuisibles. (2) Cet appareil doit accepter
toute interférence reçue y compris les interférences
causant une réception indésirable.
Ê800-10947V1^Š
INDICATION
Armed AWAY
Armed STAY
System READY
System NOT READY
Alarm while Armed
P/N 800-10947V1 8/15 Rev A
Advertisement
