Advertisement
Quick Links
INSTRUCTIONS
VHF DIGITAL TRANSCEIVER
Iç-F5122DD
UHF DIGITAL TRANSCEIVER
Iç-F6122DD
ABOUT IC-F5122DD/IC-F6122DD
Normally packet data from data software or hardware sensor
are exchanged between 2 computers or equivalent devices
using RS-232C serial cable or ETHERNET cable.
A pair of IC-F5122DD/IC-F6122DD is replacing part of com-
munication cable with a wireless connection.
RS-232C Cross cable
RS-232C
Straight cable
RF Link
RS-232C
Straight cable
Example of use:
Collecting position,
environment,
instrument,
or control information
Sending position,
environment,
instrument,
or control information
Thank you for choosing the IC-F5122DD
vhf digi
or IC-F6122DD
tal transceiver
uhf digital trans
.
ceiver
Read this instructions for periodic transceiver checks
and simple maintenance.
PANEL DESCRIPTION
Status indicator
Ethernet port*
RS-232C connector
Cloning jack
* The Ethernet port may not be installed, depending on the transceiv-
er version.
FUSE REPLACEMENT
A fuse is installed in the supplied DC power cable. If a fuse
blows, track down the source of the problem, repair it, and
then replace the damaged fuse with a new rated one.
❏ Fuse rating: 10 A
USE only a 10 A fuse.
CLEANING
If the transceiver becomes dusty or dirty, wipe it clean with a
soft, dry cloth.
DO NOT use harsh solvents such as benzine or al-
cohol, as they may damage the transceiver surfac-
es.
ABOUT THE STATUS INDICATOR
The Status Indicator indicates various transceiver status.
Status indicator
-
-
Color
Status
Green
Lit
Power ON and standing by
Blinking
Receiving data
Red
Lit
Transmitting data
Orange
Blinking
A problem occurred.
The cause may differ, depending on
the blinking pattern.
See the diagram below for de-
tails about the blinking patterns and
causes.
• Reducing the transmission output to protect the final am-
plifier
O
O
500 ms*
• PLL unlock
O
O
O
500 ms*
• Overvoltage
O
O
O
500 ms*
• Low voltage
O
O
O
O
500 ms*
*Approximately (ms: millisecond)
If the Status Indicator blinks orange, contact your dealer or
system integrator.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
ABOUT ETHERNET PORT INDICATORS
The Ethernet port indicators indicate the status of the net-
work and data.
* The Ethernet port may not be installed, depending on the transceiv-
er version.
LINK/ACT
Color
Status
SPEED Orange Not lit
Description
Lit
LINK/
Green Not lit
ACT
Lit
Blinking Receiving and Transmitting data
PIN ASSIGNMENT
• RS-232C connector
O
O
#4-40
inch screw
O
O
O
Pin No.
1
(No connection)
2
O
O
O
3
4
5
6
(No connection)
O
O
O
O
7
8
9
(No connection)
O=Orange
• Ethernet port
* The Ethernet port may not be installed, depending on the transceiv-
er version.
Pin No.
1
2
3
4
(No connection)
5
(No connection)
6
7
(No connection)
8
(No connection)
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-
porated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia, Australia, New Zealand, and/or other countries.
SPEED
Description
Connected to 10BASE-T
Connected to 100BASE-TX
Not connected to the network
Connected to the network
5
1
9
6
#4-40
inch screw
Line Name
I/O
-
RxD
OUT
TxD
IN
DTR
IN
GND
-
-
RTS
IN
CTS
OUT
-
1
8
Line Name
I/O
TX+
OUT
TX-
OUT
RX+
IN
-
-
RX-
IN
-
-
A-7202H-2EX-q
Printed in Japan
© 2015 Icom Inc.
Advertisement
