Makita DTW180 Instruction Manual
Hide thumbs
Also See for DTW180:
- Instruction manual (77 pages) ,
- Instruction manual (53 pages) ,
- Instruction manual (57 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DTW180
Summary of Contents for Makita DTW180
- Page 1 INSTRUCTION MANUAL Cordless Impact Wrench DTW180 Read before use.
- Page 2 SPECIFICATIONS Model: DTW180 Fastening capacities Standard bolt M8 - M16 High tensile bolt M6 - M12 Square drive 9.5 mm No load speed Hard impact mode 0 - 2,400 min Soft impact mode 0 - 1,300 min Impacts per minute...
-
Page 3: Specifications
Use personal protective equipment. Always SAFETY WARNINGS wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions General power tool safety warnings will reduce personal injuries. Prevent unintentional starting. Ensure the WARNING: switch is in the off-position before connecting Read all safety warnings, instruc- tions, illustrations and specifications provided with this to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with... - Page 4 Disconnect the plug from the power source Follow all charging instructions and do not and/or remove the battery pack, if detachable, charge the battery pack or tool outside the temperature range specified in the instruc- from the power tool before making any adjust- ments, changing accessories, or storing power tions. Charging improperly or at temperatures outside the specified range may damage the...
-
Page 5: Functional Description
To remove the battery cartridge, slide it from the tool SAVE THESE INSTRUCTIONS. while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the CAUTION: Only use genuine Makita batteries. battery cartridge with the groove in the housing and slip Use of non-genuine Makita batteries, or batteries that it into place. Insert it all the way until it locks in place have been altered, may result in the battery bursting with a little click. If you can see the red indicator on the causing fires, personal injury and damage. It will upper side of the button, it is not locked completely. also void the Makita warranty for the Makita tool and charger. CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. -
Page 6: Overload Protection
Press the check button on the battery cartridge to indi- Tool / battery protection system cate the remaining battery capacity. The indicator lamps light up for a few seconds. The tool is equipped with a tool/battery protection sys- tem. This system automatically cuts off power to the Indicator lamps Remaining motor to extend tool and battery life. The tool will auto- capacity matically stop during operation if the tool or battery is placed under one of the following conditions: Lighted Blinking 75% to 100% Overload protection When the battery is operated in a manner that causes 50% to 75% it to draw an abnormally high current, the tool automat- ically stops without any indication. In this situation, turn 25% to 50% the tool off and stop the application that caused the tool... - Page 7 Lighting up the front lamp Reversing switch action CAUTION: Do not look in the light or see the source of light directly. ► 1 . Reversing switch lever CAUTION: Always check the direction of ► 1 . Lamp rotation before operation. CAUTION: Use the reversing switch only after the tool comes to a complete stop.
- Page 8 Changing the impact force You can change the impact force in three steps: hard, soft, and Reverse rotation auto stop mode. This allows a tightening suitable to the work. Every time the button is pressed, the number of blows changes in three steps. ► 1 . Hard 2. Soft 3. Reverse rotation auto stop mode 4. Changed in three steps 5. Button The function of Reverse rotation auto stop mode works only with pulling the trigger fully in counterclockwise tool rotation. When the bolt/nut gets enough loosened, the tool stops the impact and rotation.
-
Page 9: Operation
ASSEMBLY OPERATION CAUTION: CAUTION: Always be sure that the tool is Always insert the battery cartridge switched off and the battery cartridge is removed all the way until it locks in place. If you can see the before carrying out any work on the tool. red indicator on the upper side of the button, it is not locked completely. Insert it fully until the red indicator cannot be seen. If not, it may accidentally fall out of... -
Page 10: Maintenance
OPTIONAL (410) ACCESSORIES (200) CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of 1. Fastening time (second) 2. Fastening torque injury to persons. Only use accessory or attachment for its stated purpose. NOTE: Hold the tool pointed straight at the bolt or nut. - Page 12 Jan-Baptist Vinkstraat 2, Makita Europe N.V. 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, Makita Corporation Anjo, Aichi 446-8502 Japan 885621-223 www.makita.com 20170802...