Table of Contents
Advertisement
........
Choosing an Effect
Recalling Effects from the Memory
The effector comes with
198
different effects stored in the
preset memory as well as a
198
effect memory capacity for
storing
the
effects you create.
You can use the following procedure to select effects from
either the preset memory or the user memory banks.
POWER
Level meter
Memory
number
display
Multi-display
Number
buttons
Shuttle ring
i j
~
-
.
-
~.
INPUT
Bank
BANK
indicators
1
Press POWER to turn on the power.
The I'LA Y screen is qisplayed.
Structure message
Category icon
(see page
19)
Memory name
_ _ l
Active parameters (see page
20)
2
Turn INPUT to adjust the analog input
levels (for digital levels, see page 13).
3
14fN
If the CLIP indicators light, the input level is set too
high. Be sme to set the input level correctly since it has
a direct relationship to the quality of the effects
(see page 10 for details).
~CH2
CH1
~
(H'
_
CLIP.
_ -6_
_-12_
_
- 1 8 _
Ir.)!:
-24 I't"'t
'"'" -30
1eI':!
r~
-36
rot
~{d81--'
Press BANK to select the memory bank
containing the effect you want (PRESETI
USER 1 or 2).
Only the bottom
indicator lights for
PRESET or USER bank 1.
2
l-:::>J
,~_
. . . : . .
_~f.~
PRESET
Both the top and bottom
indicators light for
PRESET or USER bank 2.
I;: __
.~_~
PRESET
PRESET banks 1 and 2 hold preset effects.
USER banks I and 2 are for user memory.
FUNCTION A·F
ENTER/SHIFT Operation dial
4
Select the effect you desire (1-99).
To select effects using the operation dial/shuttle ring,
rotate the dial or ring to display the number of the
effect you desire.
~
Operation dial
To select effects using the number buttons, input the
number of the effect you want, then press ENTER. (If
you press the wrong number, input the number again
before pressing ENTER.)
CDo::JCD
CD CD CD
CDCDCIJCD
+
I
ENTER)
To select effects using the arrow buttons, hold down
SHiFf and press either ... or" until the number you
desire appears in the display.
...
c=:J
+
G8
SHIFT
IT)
T
Before you turn on the connected components
Be sure to turn the volume level down to avoid an uncxpl'ded output
of massive volume.
To change effect parameters from the PLAY screen
St'l' "Editing in I'LA Y Mod .. (dire,,,t l'dit)" on page' 20.
Outputting Without Effects (BYPASS/MUTE)
The effector comes with two different bypass modes, Bypass and
Mute. Therefore, you can use the BYPASS button to cut output of the
original sound or to output the original sound without effects
depending on, which bypass mode you sell'Ct.
Once you set the BYPASS modc, just pre'Ss BYPASS to activate
Byp"ss or Mute. Prt'Ss again to cancel the bypass or mute.
BYPASS
Choosing the bypass mode
1
Press SYSTEM.
2
Press FUNCTION A to choose "Set Up."
System:
G
a.~
~
~
:x
Set
UP
Memry
Pedal
MID I
Morph
~
...... --
3
Press FUNCTION C to choose "Bypass."
Setup
.. @ fI/\-
Jjji1.
liD
Ge
Gate
Bypass
DISP
Clock
Dry off
4
Use the operation dial to select BYPAS or
Mute.
!;
ystem:SypassMoae----------
j
BY PAS
1 m m J _
select
BY PAS
Mute
when
you w,mt to output the original signal
without adding any cfte'CtS. Only the
original signal is output (Sl'\! "Bypass and
Mute" on page
11).
you want to completely cut the sound
output from the effl'Ct"r (including the
input signal). We l'Specially rl'Commend
using mute whe'll Ctlllnl'Cting the dft'Ctor
ill a send-return loop with a mixer (as
showil on p,'ge
12).
Press
EXIT
a
few times to return to the PLAY screen.
1
SEN
Advertisement
Table of Contents
