Table of Contents
Related Manuals for Belkin F7C037
Summary of Contents for Belkin F7C037
-
Page 1: User Manual
BaBy video Digital ViDeo BaBy Monitor with night Vision English User Manual Français DEUtsch nEDErl anDs Español italiano portUgUês polsKi ČEsK Y sLOVENsK Y MAGYAR РУССКИЙ БЪЛГАРСКИ ROMÂNĂ ΕΛ ΛΗΝΙΚ Α F7C037_8830ed01744uk_Rev.A00 türKçE... -
Page 2: Table Of Contents
tablE oF contEnts Your Digital baby video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 setting up . - Page 3 YOUR BELKiN DiGitAL ViDEO BABY MONitOR Baby unit Camera infra red LEDs The Baby unit is also referred to as a CAM (camera) in this guide. Back-up light for night vision. Power on/off Press and hold to turn on or off.
- Page 4 YOUR BELKiN DiGitAL ViDEO BABY MONitOR Back of Baby unit temperature sensor speaker To listen to lullabies and parent’s voice when Talk feature is used. Power socket (beneath the rubber cover) Antenna Battery compartment cover threaded socket (6mm) Used for the wall mounting bracket supplied...
- Page 5 YOUR BELKiN DiGitAL ViDEO BABY MONitOR Parent unit Link light On = strong signal is detected between the Parent and Baby unit. Flashing = Parent unit cannot link to the Baby unit. Off = Parent unit is turned off. Battery light On = Parent unit battery is being charged.
- Page 6 YOUR BELKiN DiGitAL ViDEO BABY MONitOR Parent unit Up/Vol+ Press to increase the Parent unit speaker volume. (continued) Press to scroll up a menu. Whilst viewing in zoom mode, press to move up. Whilst viewing in multi-CAM mode, press to scroll up to highlight a certain camera.
- Page 7 YOUR BELKiN DiGitAL ViDEO BABY MONitOR Parent unit screen display icons sound level indicators Light up to indicate the level of sound being transmitted from the Baby unit. speaker volume Connection status Light up when adjusting the speaker volume level.
-
Page 8: Setting Up
sEtting Up Parent unit Warning Only use the battery supplied. Using another type could permanently damage 1.Remove the plastic protective the unit. Antenna film from the front of the unit. Release Insert the battery supplied into Battery performance the battery compartment. It the operating time for using the will only fit one way round. - Page 9 sEtting Up The Parent unit rechargeable Removing the battery battery will lose charge over a period of time, even if switched off. If the Parent unit is not going to be If you ever need to remove the battery, unplug the power used for a long time, remove the adaptor and then open the battery compartment cover.
- Page 10 sEtting Up Warning 5. Once the Parent unit battery has fully charged, press button on the Parent unit until the screen becomes Do not mix old and new batteries. Only use the recommended type of 4 AA active. The battery icon on the top line of the screen will be batteries.
- Page 11 sEtting Up Removing the batteries When you need to remove the batteries, unplug the power adaptor and then open the battery compartment cover and use the ribbon to gently pull them out. 2. Plug the power adaptor cable into the socked marked on the side of the Baby unit and plug the other end into the mains power and switch on.
-
Page 12: Positioning And Operating Range
sEtting Up Positioning and operating range Positioning We recommend you place the Baby unit between 1-2 metres away from your baby for best performance. Make sure the unit and cable is out of reach of your baby. Do not place the Parent and Baby units too close together as you will hear a high-pitched noise, this is normal. - Page 13 sEtting Up testing the units before use If no connection can be established, the Parent unit will display No link to CAM for a few seconds, then Waiting for It is important that you test the units before use and at regular times thereafter, especially if linking…...
- Page 14 • you are not drilling into any position before wall mounting. hidden wiring or plumbing Belkin are not responsible for 1.Place the wall mounting bracket against the wall any damage/injury caused while where you want to wall mount the Baby unit and use attempting to wall mount a pencil to mark the top two holes as shown.
- Page 15 Baby unit in place. å is fixed, then attach the other screw in the top hole. Your Belkin Digital Video Baby Monitor is now ready for use.
- Page 16 UsiNG YOUR BELKiN DiGitAL ViDEO BABY MONitOR Using the Baby unit When the maximum or minimum volume levels have been reached you will hear an error tone. switch the Baby unit on/off 1.Press and hold the button until the light on the button turns on.
- Page 17 UsiNG YOUR BELKiN DiGitAL ViDEO BABY MONitOR to play lullabies Lullaby playback will be paused if the Talk feature is being used, Press the button to play. when finished lullaby playback will resume. Skip Press the button to skip to the next lullaby.
- Page 18 UsiNG YOUR BELKiN DiGitAL ViDEO BABY MONitOR Adjust the Parent unit loudspeaker volume You can adjust the loudspeaker volume from Volume 1 to Volume 7 or you can switch it off. The default setting is Volume 4. When the loudspeaker volume is set to off, the icon appears on the screen and the light turns on.
- Page 19 UsiNG YOUR BELKiN DiGitAL ViDEO BABY MONitOR Multi-CAM mode is not available if View only one Baby unit is paired to the Parent unit. You can change the screen to view images from different Baby units (if you have more than one Baby unit), or you can turn the screen off.
- Page 20 UsiNG YOUR BELKiN DiGitAL ViDEO BABY MONitOR The Talk feature will not work in talk to the Baby unit multi-CAM view mode. You will need to select a Baby unit in single-CAM You can use the Parent unit Talk feature as a one-way intercom view mode to use Talk.
-
Page 21: Parent Unit Settings Menu
parEnt Unit sEttings MEnU Using the menu To return to the previous menu at any time, press the button. button on the Parent unit can be used to select and change The default setting is on. settings on the Baby and Parent units. You can access the menu by: The Baby unit low battery alert 1.Press the button. - Page 22 parEnt Unit sEttings MEnU The default setting is on. 3.Press again to select Low Battery Tone. The No link alert will only work 4Use to select On or Off, then press when viewing that particular Baby confirm. You will hear a confirmation tone. unit in single-CAM or multi-CAM mode.
- Page 23 parEnt Unit sEttings MEnU sensitivity level To briefly override the sensitivity setting, to hear all sounds in baby’s You can change the sensitivity level of sounds being received room (for 15 seconds), briefly press from the Baby unit from Level 1 to Level 5 (maximum). The button on the Parent unit.
- Page 24 Baby unit you The temperature sensor used want or all Baby units, then press in this Belkin Digital Video Baby Monitor is intended as a 4.Use to select the level you want from Level 1 to Level...
- Page 25 parEnt Unit sEttings MEnU Please note that your own 3.Press again to select Minimum. temperature reference e.g. your central heating thermostat may not 4.Press to choose the Baby unit you be as accurate, possibly due to want or all Baby units, then press or .
- Page 26 parEnt Unit sEttings MEnU The default setting is On. 5.Use to select the temperature you want, then The temperature alert will only work press to confirm. You will hear a confirmation tone. when viewing that particular Baby unit in single-CAM or multi-CAM mode.
- Page 27 parEnt Unit sEttings MEnU set the temperature format You can set the temperature format as either Celsius or Fahrenheit. The default setting is Celsius. 1.Press 2.Press to highlight TEMPERATURE, then press 3.Press to highlight Format, then press 4.Press to choose Celsius or Fahrenheit, then press to confirm.
- Page 28 parEnt Unit sEttings MEnU The following events will cause the Vibrate Parent unit to vibrate (when set to do so): You can set whether you want the Parent unit to vibrate. The vibrate setting is pre-set to On if speaker is off. •...
- Page 29 parEnt Unit sEttings MEnU Even when enabled, the sound sound activated screen activated acreen functionality will temporarily be suspended if you When the Parent unit screen is turned off (see page 28), you press any button on the Parent unit. can set the screen to turn on automatically whenever there are To resume sound activated screen sounds detected from the Baby unit(s).
- Page 30 parEnt Unit sEttings MEnU 2.Press to highlight BRIGHTNESS, then press or . 3.Press to select the brightness you want from Level 1 to Level 5, then press to confirm. You will hear a confirmation tone. Display language You can select the language to be displayed on screen: English, French or Spanish.
- Page 31 parEnt Unit sEttings MEnU Pair/unpair CAM If pairing fails, the screen will display Pairing failed. Try the pairing procedure again. The Parent and Baby unit supplied are already paired but you If you pair a new Baby unit to an can add or replace Baby units you purchase separately.
- Page 32 parEnt Unit sEttings MEnU You have 60 seconds to complete 5.When the display shows Please press both the pairing process once the Parent keys on CAM unit until POWER indicator flashes Red and unit display shows Please press Green light, press and hold the buttons for 5 both keys on CAM unit...
- Page 33 parEnt Unit sEttings MEnU to unpair a Baby unit from the Parent unit Firstly, make sure the Baby and Parent units are turned on, see pages 25 and 26. 1.Press on the Parent unit. 2.Press to highlight PAIR/UNPAIR CAM, then press 3.Press to select Unpair CAM, then press 4.Press...
-
Page 34: Help
hElp My Parent and Baby units do not work at all My Parent and Baby unit(s) are producing a high-pitched noise • check that the power adaptor cables are inserted correctly into • the Parent and Baby unit(s) may be too close together. the Parent and Baby unit(s) and switched on at the wall socket. - Page 35 hElp the Parent unit doesn’t play any sound when the Parent unit plays all sounds from the there is noise from the Baby unit Baby unit and i think it is too noisy • make sure the Parent unit has power. Check that the power adaptor •...
- Page 36 hElp the battery does not charge in the Parent unit • make sure the battery is installed correctly. The battery light on the Parent unit should be on when charging. • try removing the battery completely and installing it again, then charge for up to 12 hours. •...
-
Page 37: Support And Warranty
What is not covered by this warranty? 2-Year Product Warranty All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin determines that the Belkin product has been improperly installed, altered What this warranty covers. - Page 38 Belkin reserves the right to review the damaged Belkin product. 1 . Contact Belkin International, Inc., on the telephone number All costs of shipping the Belkin product to Belkin for inspection listed on the next page, within 15 days of the Occurrence.
-
Page 39: Technical Support
AND WARRANtY technical support http://www.belkin.com/support http://www.belkin.com/uk/support Australia http://www.belkin.com/au/support New Zealand http://www.belkin.com/au/support singapore 1800 622 1130 Europe http://www.belkin.com/uk/support NORWAY 81 50 0287 www.belkin.com/uk/networking/ AUSTRIA 0820 200 766 www.belkin.com/de/networking/ www.belkin.com/nl/networking/ BELGIUM 07 07 00 073 POLAND 00800 - 441 17 37 www.belkin.com/uk/networking/... - Page 40 Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO,...
-
Page 41: Regulatory
We, Belkin International, Inc., of Schiphol-Rijk, Netherlands, protection against harmful interference in a residential installation. declare under our sole responsibility that the device, F7C037, complies with Directives stated in our EU declaration This equipment generates, uses, and can radiate radio which can be obtained from our website given below. -
Page 42: General Safety Information
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC, the EMC Directive 2004/108/EC, and the low-voltage Directive 2006/95/EC. A copy of the European Union CE marking “Declaration of Conformity” may be obtained at the website: www.belkin.com/doc For information on product disposal please refer to http://environmental.belkin.com... - Page 43 © 2014 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. iPad, iPhone, iPod touch, Mac, Mac OS, and Safari are trademarks of Apple Inc., registered in the U.S. and other countries. Windows, Windows Vista, Internet Explorer, and DirectX are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.