YOUR belkin babY 250 Parent unit baby sound level leDs Parent unit Indicates the level of received sound. The LEDs will light up progressively as the sound increases. See page 18 for further information. Mute leD Steady red indicates that Mute All has been switched on.
Page 4
YOUR belkin babY 250 Parent unit (continued) battery status indicator Red light indicates the batteries are low and need re-charging. link indicator Steady green indicates that the Baby and Parent units are linked. Flashes green if no link established for 30 seconds.
Page 5
YOUR belkin babY 250 Parent unit display icons Nightlight Music Feed Timer Setup Battery status Full charge (75-100%) Temperature alert (vibrate on) Medium charge (51-74%) Temperature alert (vibrate off) Low charge (25-50%) Nightlight is on Empty (8-24%) Music is playing...
YOUR belkin babY 250 Parent unit charger front back Charging light Power socket Charging light Power socket Red when the Parent unit is correctly placed on the charger. For connection to the mains power socket via the power adapter cable supplied.
Page 7
YOUR belkin babY 250 baby unit baby unit nightlight Press to switch the Nightlight on or off. Power on/off Press and hold to switch the power on or off. skip forward When music has been switched on (see Music button description below), press to skip through the songs available.
seTTing UP Warning! Only use the power adapters supplied. Using incorrect power adapters may permanently damage your product. Battery performance Rechargeable batteries in the Parent unit will last approximately 20 hours in normal use. Please note that new batteries do not reach full capacity until they have been in normal use for several days.
Page 10
seTTing UP Parent unit Activate the batteries by pulling the plastic tab Plug one of the power adapter cables into the socket marked away from the bottom of the Parent unit. on the back of the Parent unit charger and plug the other end into the mains power wall socket and switch the power on.
Page 11
seTTing UP Battery low warning – Parent unit When the batteries are low – approximately within 1 hour of running out – the Parent unit will emit a low battery alert, the low battery indicator will turn red, the display will show Low battery indicator Low Battery and the icon will flash.
Page 12
seTTing UP Removing the batteries If you ever need to remove the batteries, simply slide open the battery compartment cover and use the ribbon to eject the batteries. switch on and link the Parent and baby units 1.Press and hold the button on the Baby unit for 1 second.
Page 13
seTTing UP important: Positioning your units The link confirmation between the two units is vital for use so The Baby unit should ideally be within 1m-2m they can communicate. If the link between the units is broken of your baby for best performance. at any time, the Link indicators on the Parent and Baby units will flash green as they try to search for each other.
Using YOUR belkin babY 250 switching on/off baby sound level leD indicators switch the baby unit on LEDs 1-2 = Green LEDs 3-4 = Green LEDs 5-7 = Red (or Amber if Mute Low is on) 1. Press and hold the button for 1 second.
Using YOUR belkin babY 250 adjust the Parent unit loudspeaker volume Mute all feature – Parent unit only at the Parent unit: The Mute All feature prevents any sound coming out 1.Press to select the required level. The first press will from the Parent unit loudspeaker.
Page 16
Using YOUR belkin babY 250 Be careful not to accidentally Mute low switch the torch feature on because Mute All is automatically switched For discreet operation when you do not wish to hear on when the Torch is switched on.
Page 17
Using YOUR belkin babY 250 When the Torch is switched on it find will automatically switch Mute All on as well. If you then press the You can press the button on the Baby unit to make the Parent unit button Mute will be disabled and sound an alert beep to help you find it if it’s been misplaced.
Page 18
Using YOUR belkin babY 250 The Parent unit menu button on the Parent unit can be used to select and change settings on the Baby unit without having to risk disturbing your baby. You can access the settings by: 1.Press...
Page 19
Using YOUR belkin babY 250 The Baby unit must be switched on nightlight for the nightlight to work, but need not be linked to the Parent unit. You can set a comforting nightlight on the Baby unit. There are 3 brightness levels to choose from and you can set a period of time for the nightlight to illuminate.
Page 20
Using YOUR belkin babY 250 The default setting is Medium. select the nightlight brightness level using the Parent unit 1. Press . Nightlight is displayed, press 2. Press to display Brightness and press 3. Press to display either Low, Medium or High and press to select.
Page 21
Using YOUR belkin babY 250 Adjust the volume of the music Turn music on/off using the baby unit using the buttons on the Baby unit. 1. To turn the music on, press the button. The most recently selected song will start playing at the time period last selected using the Parent unit.
Page 22
Using YOUR belkin babY 250 The eight song choices are: 3 Blind Choose a song to play using the Parent unit Mice, Brahms, Canon in D, Dream Chase, Dreaming, Hush Baby, 1. Press . Nightlight is displayed, press Night Night and Twinkle Star.
Page 23
Using YOUR belkin babY 250 The timer can be set to countdown feed Timer from 1 minute to 99 hours 59 minutes. You can set a Feed Timer on the Parent unit to act as a countdown timer that will alert you when you next need to feed your baby.
Page 24
Using YOUR belkin babY 250 start the feed timer countdown 1. Press . Nightlight is displayed, press until Feed Timer is displayed and press 2. Start? is displayed, press . The display will briefly show Timer On and then the timer will be shown counting down the seconds from the time you set.
Page 25
Using YOUR belkin babY 250 switch timer repeat option on or off 1. Press . Nightlight is displayed, press until Feed Timer is displayed and press 2. Start? is displayed, press until Repeat is displayed and press 3. Use the...
Page 26
Temperature monitor iMPORTanT! The temperature sensor used in this Belkin baby 250 is intended as There is a temperature sensor on the Baby unit to constantly a guide, to provide parents with an monitor the temperature in your baby’s room and you’ll be alerted...
Page 27
Using YOUR belkin babY 250 Pre-set temperature alert range select the type of temperature alert The Baby unit comes with pre-set maximum and minimum 1. Press . Nightlight is displayed, press temperatures, as stated by the until SetUp is displayed and press...
Page 28
Using YOUR belkin babY 250 Crying alert Crying alert options Beep = Parent unit will beep, Crying Alert will be displayed and The crying alert will only be activated if Mute All has been switched icon will flash. on (or if the Parent unit volume has been switched to volume off), see page 20 for information on the Mute All feature.
Page 29
Using YOUR belkin babY 250 backlight list of tones You can select whether or not the LCD backlight comes on Your Baby Monitor unit can when an alert is activated. When the backlight comes on it produce various tones. They will stay on for 15 seconds.
Page 30
Using YOUR belkin babY 250 Resetting the units is only User Alert tones can be silenced by pressing advisable if you are experiencing any button on the Parent unit. difficulties with your product. It is a useful feature that ensures your...
HelP Parent unit is beeping link light is flashing green • The link has been lost between your units. Check that the • If you have pressed to use the Talk Back feature, the Link light Baby unit Link indicator is illuminated. If not, please ensure will flash to indicate one-way communication between the units.
Page 32
HelP Parent unit remains silent or very quiet You can hear a high pitched noise • You may have set the volume too low • The units might be too close to each other. • You may have switched a Mute feature on. •...
What is not covered by this warranty? 2-Year Product Warranty All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin determines that the Belkin product has been improperly installed, altered What this warranty covers .
Page 34
Belkin reserves the right to review the damaged Belkin product. 1 . Contact Belkin International, Inc., on the telephone number All costs of shipping the Belkin product to Belkin for inspection listed on the next page, within 15 days of the Occurrence.
WaRRanTY Technical support http://www.belkin.com/support http://www.belkin.com/uk/support australia http://www.belkin.com/au/support new Zealand http://www.belkin.com/au/support singapore 1800 622 1130 europe http://www.belkin.com/uk/support NORWAY 81 50 0287 www.belkin.com/uk/networking/ AUSTRIA 0820 200 766 www.belkin.com/de/networking/ www.belkin.com/nl/networking/ BELGIUM 07 07 00 073 POLAND 00800 - 441 17 37 www.belkin.com/uk/networking/...
Page 36
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO,...
Class B digital device, pursuant to the requirements of EN 55022 and EN 55024. These limits are designed to provide reasonable We, Belkin International, Inc., of Schiphol-Rijk, Netherlands, protection against harmful interference in a residential installation. declare under our sole responsibility that the device, F7C035,...
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC, the EMC Directive 2004/108/EC, and the low-voltage Directive 2006/95/EC. A copy of the European Union CE marking “Declaration of Conformity” may be obtained at the website: www.belkin.com/doc For information on product disposal please refer to http://environmental.belkin.com...