Related Manuals for Toyota Corolla TNS600 2004
Summary of Contents for Toyota Corolla TNS600 2004
- Page 1 Corolla TNS600 RHD installation instructions Model year: 2004 Vehicle code: **E12*R-****W Part number: • Navigation System PZ 445-00331-00 • Clusterpanel 55406-02070-B0 Manual ref. n : AIM 000 767-0...
-
Page 2: Precautions
Corolla TNS600 PRECAUTIONS PLEASE READ THOROUGHLY THESE PRECAUTIONS BEFORE THE INSTALLATION • Protect your car with fender cov- • Be sure to disconnect the negative ers, seat and so on. (-) lead from the battery terminals. • Use the correct tool when tight- •... -
Page 3: Table Of Contents
Corolla TNS600 TABLE OF CONTENTS Precautions ............................. Component Parts ........................... Required Parts ............................Wiring Connection ..........................Installation Overview ..........................Installation of the GPS Antenna ......................Wire Harness Installation ......................... Installation of Navigation Disc ........................ Post-Installation Inspection ........................Reassembling ............................Corolla (RHD) - 3 01-07... - Page 4 PWR•VOL VOICE NAVIGATION TUNE SEEK TRACK MENU DEST INFO VOICE AUDIO DISPLAY TILT OPEN TOYOTA B-9001 Description TNS600 WIRE HARNESS GPS ANTENNA NAVIGATION DISC CORD CLAMP FOAM TAPE 2 + 3 WIRE TIE EARTH PLATE 01-07 Corolla (RHD) - 4...
-
Page 5: Component Parts
Corolla TNS600 COMPONENT PARTS 55406-02070-B0 REQUIRED PARTS OWNER’S MANUAL To be ordered separately. Refer to ATA database for partnumbers Corolla (RHD) - 5 01-07... -
Page 6: How To Connect
Corolla TNS600 HOW TO CONNECT Splicing connector Splicing connector TNS 600 Tuner with LCD Display (Speed sensor wire) (Reverse sensor wire) GPS antenna Vehicle wire harness Antenna wire Refer to the repair manual for information on removal of vehicle parts, installation methods, tightening torque etc. -
Page 7: Installation Overview
Corolla TNS600 INSTALLATION OVERVIEW Splicing Connector GPS Antenna Splicing Connector (Reverse sensor wire) Corolla (RHD) - 7 01-07... - Page 8 Corolla TNS600 Remove the ashtray Fig. 1 FOR MANUAL TRANSMISSION Remove the shift knob FOR ALL MODELS Remove the console panel : Hook (6x) CAUTION Put the protective tapes on the sha- ded areas. Be sure to remove the parts carefully not to damage the section.
- Page 9 Corolla TNS600 FOR MANUAL A/C MODELS Remove the knob and the heater control panel : Screw (1x) : Clip (4x) : Hook (4x) CAUTION Put the protective tapes on the sha- ded areas. Be sure to remove the parts carefully not to damage the section. Fig.
- Page 10 Corolla TNS600 Remove the glove box : Hook (2x) Fig. 7 01-07 Corolla (RHD) - 10...
-
Page 11: Installation Of The Gps Antenna
Corolla TNS600 INSTALLATION OF THE GPS ANTENNA Cut the foam into 4 large pieces, 8 middle pieces and 8 small pieces as shown in the illustration. Fig. 8 Remove the release paper of the earth plate and attach the butyl tape shown. - Page 12 Corolla TNS600 Attach the earth plate to the meter GPS Antenna cluster panel as shown and mount the GPS antenna to the earth plate b) Fix the antenna cord using foam (3x). CAUTION Make sure to clean the installation position surface before attaching the earth plate Mitte Centre...
-
Page 13: Wire Harness Installation
Corolla TNS600 WIRE HARNESS INSTALLATION Route the antenna cord as shown in the illustration. Fig. 12 Cut the red/white wire away isolate Fig. 13 G WIRE SPLICING CONNECTOR INSTRUCTIONS Remove appropriate amount of tape wrapping the vehicle side harness to be connected. - Page 14 Corolla TNS600 Remove the speed signal from 20 pin connector (pin 3) Fig. 15 G SPEED SENSOR CONNECTION The connector shown in the illustration is the vehicle side connector to be spliced. Fig. 16 01-07 Corolla (RHD) - 14...
- Page 15 Corolla TNS600 Connect the speed sensor wire (vio- let/white) of the wire harness terminal 15 of the 20P connector. WIRE SIDE VIEW Vehicle Wire Harness Fig. 17 Disconnect the 10P connector. b) Route reverse sensor wire (red/green) as shown in the illustra- tion, and secure the reverse sensor wire using foam (5x).
- Page 16 Corolla TNS600 Dissassemble the original cluster . Fig. 20 10. Disassemble the brackets Fig. 21 11. Assemble the brackets to the TNS600 Fig. 22 01-07 Corolla (RHD) - 16...
-
Page 17: Installation Of Navigation Disc
4. Perform the “auto-compensation” procedure by following the section on “When Tires are Replaced” in the TNS Owner’s Manual. When an abnormality is suspected, perform troubleshooting based on the “Toyota Genuine Navigation System Service Manual”. REASSEMBLING Return all vehicle parts that have been removed to their original locations. - Page 18 GENUINE PARTS...