Table of Contents
Advertisement
Quick Links
Cisco 5915 Embedded Services Router
Hardware Technical Guide
Current Release:
January 2018
This guide describes the Cisco 5915 Embedded Services Router (ESR) including product specifications,
installation procedures, and hardware information.
About This Guide
This guide is organized into the following sections:
•
•
•
•
•
•
•
•
•
•
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
About This Guide, page 1
–
Audience, page 2
–
Related Documentation, page 2
–
Conventions, page 2
Introduction, page 3
Cisco 5915 ESR Conduction-Cooled Card, page 4
–
Installing the Cisco 5915 ESR Conduction-Cooled Card, page 6
–
Removing the Cisco 5915 ESR Conduction-Cooled Card, page 7
Cisco 5915 ESR Air-Cooled Card, page 7
Cisco 5915 ESR LED Definitions, page 9
Factory Default, page 10
Temperature Out of Range Detection, page 11
Using the Cisco 5915 ESR, page 11
Product Specifications, page 12
Hardware Information, page 14
–
Cisco 5915 ESR Conduction-Cooled Card Layout and Dimensions, page 14
Advertisement
Table of Contents
Related Manuals for Cisco 5915
Summary of Contents for Cisco 5915
-
Page 1: About This Guide
Cisco 5915 Embedded Services Router Hardware Technical Guide Current Release: January 2018 This guide describes the Cisco 5915 Embedded Services Router (ESR) including product specifications, installation procedures, and hardware information. About This Guide This guide is organized into the following sections: •... -
Page 2: Related Documentation
• Obtaining Documentation and Submitting a Service Request, page 19 Audience This guide is for system integration engineers who are incorporating the Cisco 5915 ESR board into a chassis. Related Documentation Use these publications to help you configure Cisco IOS software features: •... -
Page 3: Introduction
The inclusive and compact design simplifies integration and offers system integrators the ability to use the Cisco 5915 ESR in a wide variety of applications. The user interface for Cisco 5915 ESR is through edge fingers. Air-cooled and conduction-cooled models accommodate diverse operational environments. -
Page 4: Cisco 5915 Esr Conduction-Cooled Card
Cisco 5915 ESR Conduction-Cooled Card Figure 1 Cisco 5915 Embedded Services Router - Top Side View Figure 2 Cisco 5915 Embedded Services Router - Bottom Side View Cisco 5915 ESR Conduction-Cooled Card The Cisco 5915 ESR conduction-cooled card (Figure 3... - Page 5 Cisco 5915 ESR Conduction-Cooled Card Figure 3 Cisco 5915 ESR Conduction-Cooled Card - Bottom View Table 1 Cisco 5915 ESR Conduction-Cooled Card - Bottom View Markings PCI Connector Edge Finger (Main) Edge Finger (Auxiliary) Thermal Plate (Bottom) Cisco 5915 Embedded Services Router Hardware Technical Guide...
-
Page 6: Installing The Cisco 5915 Esr Conduction-Cooled Card
When performing the following procedures, wear a grounding wrist strap to avoid ESD damage Warning to the Cisco 5915 ESR conduction-cooled card. Some platforms have an ESD connector for attaching the wrist strap. Do not directly touch the edge finger or PCI connector pins with your hand or any metal tool to avoid component failure. -
Page 7: Removing The Cisco 5915 Esr Conduction-Cooled Card
Carefully remove the Cisco 5915 ESR conduction-cooled card out of the conduction-cooled chassis. Cisco 5915 ESR Air-Cooled Card The Cisco 5915 ESR air-cooled card operates at a temperature range of -40ºC to +70ºC. Forced air is used to cool the card. - Page 8 Cisco 5915 ESR Air-Cooled Card Figure 5 Cisco 5915 ESR Air-Cooled Card - Bottom View Table 3 Cisco 5915 ESR Air-Cooled Card - Bottom View Markings PCI Connector Edge Finger (Main) Edge Finger (Auxiliary) Figure 6 Cisco 5915 ESR Air-Cooled Card - Top View...
-
Page 9: Cisco 5915 Esr Led Definitions
PCI Connector Edge Finger (Auxiliary) Cisco 5915 ESR LED Definitions Cisco 5915 ESR supports the LED control signals described in Table 5. These signals go to the edge fingers and connect to LEDs in the solution developed by a system integrator. -
Page 10: Factory Default
1. The erase time of the Flash file system depends on the utilization of the Flash device. It takes more time to delete a fully utilized file system. To start the Cisco 5915 ESR factory default process, pull the INPUT_CLEAR_L signal to GND (Figure 8). -
Page 11: Temperature Out Of Range Detection
ROMMON because the Flash file system that normally contains IOS is empty. If you choose to use the erase-all option, the Cisco 5915 ESR will have no user data or binary code in router memory after the factory default process is complete. -
Page 12: Product Specifications
For integrators planning to use the conduction-cooled Cisco 5915 ESR, mounting holes are in the thermal plate. These mounting holes are used to hold an I/O board or flex circuit to the Cisco 5915 ESR. The mounting hole size is 0.125 Inches (diameter). Four 4-40 pan head screws are required. - Page 13 6.14W Note There are no voltage rail sequencing requirements. Power supply voltage rails can power-up/power-down in any order. Both the 3.3V and 5V rails are required for the Cisco 5915 ESR. Cisco 5915 Embedded Services Router Hardware Technical Guide OL-24796-01...
-
Page 14: Hardware Information
2. All values determined using 90% Upper Confidence Level (UCL) for the steady-state failure rate calculated per Telcordia SR-332, Issue 2, September 2006. Hardware Information This section shows layout of the Cisco 5915 ESR cards, pinout assignments, and other hardware specification information. Cisco 5915 ESR Conduction-Cooled Card Layout and Dimensions The following figures show the layout and dimensions of the Cisco 5915 ESR conduction-cooled card. -
Page 15: Cisco 5915 Air-Cooled Card Layout And Dimensions
Layout of the CIsco 5915 ESR Conduction-Cooled Card Cisco 5915 Air-Cooled Card Layout and Dimensions Figure 10 shows the layout and dimensions of the Cisco 5915 ESR air-cooled card. The dimensions are in inches. Cisco 5915 Embedded Services Router Hardware Technical Guide... -
Page 16: Edge Fingers Interfaces
Layout of the Air-Cooled Card Edge Fingers Interfaces The Cisco 5915 ESR edge fingers provide system interface signal connectivity, while maximizing the real estate available for component placement. The connector solution is borrowed from the PCIe standard. The edge fingers consist of 64 pins in the main connector (Table 8). - Page 17 ETH_FE0/2_RX- ETH_FE0/3_TX- ETH_FE0/3_RX+ ETH_FE0/3_TX+ ETH_FE0/3_RX- ETH_FE0/4_TX- ETH_FE0/4_RX+ ETH_FE0/4_TX+ ETH_FE0/4_RX- ETH_FE0/0_TX- ETH_FE0/0_RX+ ETH_FE0/0_TX+ ETH_FE0/0_RX- ETH_FE0/1_TX- ETH_FE0/1_RX+ ETH_FE0/1_TX+ ETH_FE0/1_RX- Note The FE0/0, FE0/1 are routed ports. FE0/2, FE0/3, and FE0/4 are switched ports. Cisco 5915 Embedded Services Router Hardware Technical Guide OL-24796-01...
-
Page 18: Pci Connector
The Cisco 5915 ESR is PCI-104 compliant and supports the standard PCI connector. Table 9 lists the pinout assignments. However, the Cisco 5915 ESR does not connect to the PCI bus because it is not used. The only electrical connections to the PCI connector are +5V, +3.3V, and GND. Note The Cisco 5915 ESR uses the variant of the PCI bus stacking connector, which is keyed on pin D30. -
Page 19: Obtaining Documentation And Submitting A Service Request
RSS Version 2.0. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. - Page 20 Obtaining Documentation and Submitting a Service Request Cisco 5915 Embedded Services Router Hardware Technical Guide OL-24796-01...