Radio Shack 42-4058 Owner's Manual page 35

Stereo This is a stereo phaser that modulates the
09
Phaser phase in accordance with a sine wave LFO.
This is a monaural phaser that modulates the
10 Phaser
phase in accordance with a sine wave LFO.
11 Rotary This is a rotary speaker simulator.
12 Drive Rotary This is an overdrive-rotary speaker simulator.
Enhances the outlines of the low range and
13 Enhancer
high range of the input signal.
This is a ring modulator (AM modulator) that
Ring makes it possible to modulate the frequency of
14
Modulator internal oscillator (OSC) in accordance with an
internal LFO.
This is an effector that reproduces a retro-type
Lo-Fi sound using Noise Generator 1 (phono-
graph record player type scratch noise
generator) and Noise Generator 2 (FM radio
15 Lo-Fi
type white noise and pink noise continuous
noise generator), and by using noise
modulation (amplitude modulation = AM) and
distortion of frequency characteristics.
1-Phase This is a monaural chorus in accordance with a
16
Chorus sine wave LFO.
Sin 2-Phase This is a stereo chorus in accordance with a
17
Chorus sine wave LFO.
3-Phase This is a 3-phase chorus in accordance with two
18
Chorus LFOs of with different sine wave rates.
Tri 2-Phase This is a stereo chorus in accordance with
19
Chorus triangular wave LFO.
Stereo
20 This is a delay of stereo input and output.
Delay 1
0: Resonance (0 to 127) – Adjusts the resonance of the sound.
1: Manual (-64 to 0 to +63) – Adjusts the phaser shift volume, which is used for
reference.
2: Rate (0 to 127) – Adjusts the rate of the LFO.
3: Depth (0 to 127) – Adjusts the depth of the LFO.
4: Wet Level (0 to 127) – Adjusts the volume level of the effect.
0: Resonance (0 to 127) – Adjusts the resonance of the sound.
1: Manual (-64 to 0 to +63) – Adjusts the phaser shift volume, which is used for
reference.
2: Rate (0 to 127) – Adjusts the rate of the LFO.
3: Depth (0 to 127) – Adjusts the depth of the LFO.
4: Wet Level (0 to 127) – Adjusts the level of the effect sound.
0: Speed (Slow, Fast) Switches the speed mode between fast and slow.
1: Break (Rotate, Stop) Stops speaker rotation.
2: Fall Accel (0 to 127) – Adjusts acceleration when the speed mode is switched
from fast to slow.
3: Rise Accel (0 to 127) – Adjusts acceleration when the speed mode is switched
from slow to fast.
4: Slow Rate (0 to 127) – Adjusts speaker rotation speed in the slow speed
mode.
5: Fast Rate (0 to 127) – Adjusts speaker rotation speed in the fast speed mode.
0: Overdrive Gain (0 to 127) – Adjusts overdrive gain.
1: Overdrive Level (0 to 127) – Adjusts the output level of the overdrive.
2: Speed (Slow, Fast) Switches the speed mode between fast and slow.
3: Break (Rotate, Stop) Stops speaker rotation.
4: Fall Accel (0 to 127) – Adjusts acceleration when the speed mode is switched
from fast to slow.
5: Rise Accel (0 to 127) – Adjusts acceleration when the speed mode is switched
from slow to fast.
6: Slow Rate (0 to 127) – Adjusts speaker rotation speed of the slow speed mode.
7: Fast Rate (0 to 127) – Adjusts speaker rotation speed of the fast speed mode.
0: Low Frequency (0 to 127) – Adjusts the low range enhancer frequency.
1: Low Gain (0 to 127) – Adjusts the low range enhancer gain.
2: High Frequency (0 to 127) – Adjusts the high range enhancer frequency.
3: High Gain (0 to 127) – Adjusts the high range enhancer gain.
0: OSC Frequency (0 to 127) Sets the reference frequency of the internal OSC.
1: LFO Rate (0 to 127) – Adjusts the rate of the LFO.
2: LFO Depth (0 to 127) – Adjusts the depth of the LFO.
3: Wet Level (0 to 127) – Adjusts the level of the effect sound.
4: Dry Level (0 to 127) – Adjusts the level of the original sound.
0: Noise Level 1 (0 to 127) – Adjusts the level of Noise Generator 1.
1: Noise Density 1 (0 to 127) – Adjusts the noise density of Noise Generator 1.
2: Noise Level 2 (0 to 127) – Adjusts the level of Noise Generator 2.
3: Noise Density 2 (0 to 127) – Adjusts the noise density of Noise Generator 2.
4: Tone (0 to 127) – Adjusts the tone.
5: Resonance (0 to 127) – Adjusts the resonance of the sound.
6: Bass (-64 to 0 to +63) – Adjusts the volume of low sounds.
7: Level (0 to 127) – Adjusts the output level.
0: LFO Rate (0 to 127) – Adjusts the rate of the LFO.
1: LFO Depth (0 to 127) – Adjusts the depth of the LFO.
2: Feedback (-64 to 0 to +63) – Adjusts the feedback of the sound.
3: Wet Level (0 to 127) – – Adjusts the level of the effect sound.
0: LFO Rate (0 to 127) – – Adjusts the rate of the LFO.
1: LFO Depth (0 to 127) – Adjusts the depth of the LFO.
2: Feedback (-64 to 0 to +63) – Adjusts the feedback of the sound.
3: Wet Level (0 to 127) – Adjusts the level of the effect sound.
0: Rate1 (Fast LFO Rate, 0 to 127) – Adjusts the rate of LFO1.
1: Depth1 (Fast LFO Depth, 0 to 127) – Adjusts the depth of LFO1.
2: Rate2 (Slow LFO Rate, 0 to 127) – Adjusts the rate of LFO2.
3: Depth2 (Slow LFO Depth, 0 to 127) – Adjusts the depth of LFO2.
4: Wet Level (0 to 127 – Adjusts the level of the effect sound.
0: LFO Rate (0 to 127) – Adjusts the rate of the LFO.
1: LFO Depth (0 to 127) – Adjusts the depth of the LFO.
2: Feedback (-64 to +63) – Adjusts the feedback of the sound.
3: Wet Level (0 to 127) – Adjusts the level of the effect sound.
0: Delay Time (0 to 127) – Adjusts the delay time.
1: Wet Level (0 to 127) – Adjusts the level of the effect sound.
2: Feedback (0 to 127) – Adjusts the repeat of the delay.
3: High Damp (0 to 127) – Adjusts damping of the high-range delay sound. The
smaller the value, the greater the damping of high-range delay sound.
4: Ratio L (0 to 127) – Adjusts the delay time of the left channel, proportional to
the value set for Delay Time.
5: Ratio R (0 to 127) – Adjusts the delay time of the right channel, proportional to
the value set for Delay Time.
35